Merge tag 'u-boot-imx-20190101' of git://www.denx.de/git/u-boot-imx

[oweals/u-boot.git] / drivers / net / phy / Kconfig

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 1afd8097b2fa7d8bcafbb30b16190c3e4e061bff..3dc0822d9c21cfa83591be5791fcdd7a5066a7c6 100644 (file)
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -7,11 +7,44 @@ config MV88E6352_SWITCH
 
 menuconfig PHYLIB
        bool "Ethernet PHY (physical media interface) support"
 
 menuconfig PHYLIB
        bool "Ethernet PHY (physical media interface) support"

+       depends on NET

        help
          Enable Ethernet PHY (physical media interface) support.
 
 if PHYLIB
 
        help
          Enable Ethernet PHY (physical media interface) support.
 
 if PHYLIB
 

+config PHY_ADDR_ENABLE
+       bool "Limit phy address"
+       default y if ARCH_SUNXI
+       help
+         Select this if you want to control which phy address is used
+
+if PHY_ADDR_ENABLE
+config PHY_ADDR
+       int "PHY address"
+       default 1 if ARCH_SUNXI
+       default 0
+       help
+         The address of PHY on MII bus. Usually in range of 0 to 31.
+endif
+
+config B53_SWITCH
+       bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support."
+       help
+         Enable support for Broadcom BCM53xx (RoboSwitch) Ethernet switches.
+         This currently supports BCM53125 and similar models.
+
+if B53_SWITCH
+
+config B53_CPU_PORT
+       int "CPU port"
+       default 8
+
+config B53_PHY_PORTS
+       hex "Bitmask of PHY ports"
+
+endif # B53_SWITCH
+

 config MV88E61XX_SWITCH
        bool "Marvel MV88E61xx Ethernet switch PHY support."
 
 config MV88E61XX_SWITCH
        bool "Marvel MV88E61xx Ethernet switch PHY support."
 


@@ -31,8 +64,32 @@ endif # MV88E61XX_SWITCH
 config PHYLIB_10G
        bool "Generic 10G PHY support"
 
 config PHYLIB_10G
        bool "Generic 10G PHY support"
 

-config PHY_AQUANTIA
+menuconfig PHY_AQUANTIA

        bool "Aquantia Ethernet PHYs support"
        bool "Aquantia Ethernet PHYs support"

+       select PHY_GIGE
+       select PHYLIB_10G
+
+config PHY_AQUANTIA_UPLOAD_FW
+       bool "Aquantia firmware loading support"
+       default n
+       depends on PHY_AQUANTIA
+       help
+               Aquantia PHYs use firmware which can be either loaded automatically
+               from storage directly attached to the phy or loaded by the boot loader
+               via MDIO commands.  The firmware is loaded from a file, specified by
+               the PHY_AQUANTIA_FW_PART and PHY_AQUANTIA_FW_NAME options.
+
+config PHY_AQUANTIA_FW_PART
+       string "Aquantia firmware partition"
+       depends on PHY_AQUANTIA_UPLOAD_FW
+       help
+               Partition containing the firmware file.
+
+config PHY_AQUANTIA_FW_NAME
+       string "Aquantia firmware filename"
+       depends on PHY_AQUANTIA_UPLOAD_FW
+       help
+               Firmware filename.

 
 config PHY_ATHEROS
        bool "Atheros Ethernet PHYs support"
 
 config PHY_ATHEROS
        bool "Atheros Ethernet PHYs support"


@@ -55,6 +112,9 @@ config PHY_LXT
 config PHY_MARVELL
        bool "Marvell Ethernet PHYs support"
 
 config PHY_MARVELL
        bool "Marvell Ethernet PHYs support"
 

+config PHY_MESON_GXL
+       bool "Amlogic Meson GXL Internal PHY support"
+

 config PHY_MICREL
        bool "Micrel Ethernet PHYs support"
        help
 config PHY_MICREL
        bool "Micrel Ethernet PHYs support"
        help


@@ -67,28 +127,38 @@ config PHY_MICREL
 if PHY_MICREL
 
 config PHY_MICREL_KSZ9021
 if PHY_MICREL
 
 config PHY_MICREL_KSZ9021

-       bool "Micrel KSZ9021 family support"
+       bool

        select PHY_GIGE
        select PHY_GIGE

-       help
-         Enable support for the Micrel KSZ9021 GbE PHY family.  If
-         enabled, the extended register read/write for KSZ9021 PHYs
-         is supported through the 'mdio' command and any RGMII signal
-         delays configured in the device tree will be applied to the
-         PHY during initialisation.
-
-         Note that the KSZ9021 uses the same part number os the
-         KSZ8921BL, so enabling this option disables support for the
-         KSZ8721BL.
+       select PHY_MICREL_KSZ90X1

 
 config PHY_MICREL_KSZ9031
 
 config PHY_MICREL_KSZ9031

-       bool "Micrel KSZ9031 family support"
+       bool
+       select PHY_GIGE
+       select PHY_MICREL_KSZ90X1
+
+config PHY_MICREL_KSZ90X1
+       bool "Micrel KSZ90x1 family support"

        select PHY_GIGE
        help
        select PHY_GIGE
        help

-         Enable support for the Micrel KSZ9031 GbE PHY family.  If
-         enabled, the extended register read/write for KSZ9021 PHYs
+         Enable support for the Micrel KSZ9021 and KSZ9031 GbE PHYs. If
+         enabled, the extended register read/write for KSZ90x1 PHYs

          is supported through the 'mdio' command and any RGMII signal
          delays configured in the device tree will be applied to the
          is supported through the 'mdio' command and any RGMII signal
          delays configured in the device tree will be applied to the

-         PHY during initialisatioin.
+         PHY during initialization.
+
+         This should not be enabled at the same time with PHY_MICREL_KSZ8XXX
+         as the KSZ9021 and KS8721 share the same ID.
+
+config PHY_MICREL_KSZ8XXX
+       bool "Micrel KSZ8xxx family support"
+       default y if !PHY_MICREL_KSZ90X1
+       help
+         Enable support for the 8000 series GbE PHYs manufactured by Micrel
+         (now a part of Microchip). This includes drivers for the KSZ804,
+         KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, and KSZ8721.
+
+         This should not be enabled at the same time with PHY_MICREL_KSZ90X1
+         as the KSZ9021 and KS8721 share the same ID.

 
 endif # PHY_MICREL
 
 
 endif # PHY_MICREL
 


@@ -101,6 +171,16 @@ config PHY_NATSEMI
 config PHY_REALTEK
        bool "Realtek Ethernet PHYs support"
 
 config PHY_REALTEK
        bool "Realtek Ethernet PHYs support"
 

+config RTL8211E_PINE64_GIGABIT_FIX
+       bool "Fix gigabit throughput on some Pine64+ models"
+       depends on PHY_REALTEK
+       help
+         Configure the Realtek RTL8211E found on some Pine64+ models differently to
+         fix throughput on Gigabit links, turning off all internal delays in the
+         process. The settings that this touches are not documented in the CONFREG
+         section of the RTL8211E datasheet, but come from Realtek by way of the
+         Pine64 engineering team.
+

 config RTL8211X_PHY_FORCE_MASTER
        bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
        depends on PHY_REALTEK
 config RTL8211X_PHY_FORCE_MASTER
        bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
        depends on PHY_REALTEK