+config NAND_OMAP_GPMC
+ bool "Support OMAP GPMC NAND controller"
+ depends on ARCH_OMAP2PLUS
+ help
+ Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms.
+ GPMC controller is used for parallel NAND flash devices, and can
+ do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8
+ and BCH16 ECC algorithms.
+
+config NAND_OMAP_GPMC_PREFETCH
+ bool "Enable GPMC Prefetch"
+ depends on NAND_OMAP_GPMC
+ default y
+ help
+ On OMAP platforms that use the GPMC controller
+ (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that
+ uses the prefetch mode to speed up read operations.
+
+config NAND_OMAP_ELM
+ bool "Enable ELM driver for OMAPxx and AMxx platforms."
+ depends on NAND_OMAP_GPMC && !OMAP34XX
+ help
+ ELM controller is used for ECC error detection (not ECC calculation)
+ of BCH4, BCH8 and BCH16 ECC algorithms.
+ Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
+ thus such SoC platforms need to depend on software library for ECC error
+ detection. However ECC calculation on such plaforms would still be
+ done by GPMC controller.
+
+config NAND_VF610_NFC
+ bool "Support for Freescale NFC for VF610"
+ select SYS_NAND_SELF_INIT
+ imply CMD_NAND
+ help
+ Enables support for NAND Flash Controller on some Freescale
+ processors like the VF610, MCF54418 or Kinetis K70.
+ The driver supports a maximum 2k page size. The driver
+ currently does not support hardware ECC.
+
+choice
+ prompt "Hardware ECC strength"
+ depends on NAND_VF610_NFC
+ default SYS_NAND_VF610_NFC_45_ECC_BYTES
+ help
+ Select the ECC strength used in the hardware BCH ECC block.
+
+config SYS_NAND_VF610_NFC_45_ECC_BYTES
+ bool "24-error correction (45 ECC bytes)"
+
+config SYS_NAND_VF610_NFC_60_ECC_BYTES
+ bool "32-error correction (60 ECC bytes)"
+
+endchoice
+
+config NAND_PXA3XX
+ bool "Support for NAND on PXA3xx and Armada 370/XP/38x"
+ select SYS_NAND_SELF_INIT
+ imply CMD_NAND
+ help
+ This enables the driver for the NAND flash device found on
+ PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
+
+config NAND_SUNXI
+ bool "Support for NAND on Allwinner SoCs"
+ depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
+ select SYS_NAND_SELF_INIT
+ select SYS_NAND_U_BOOT_LOCATIONS
+ imply CMD_NAND
+ ---help---
+ Enable support for NAND. This option enables the standard and
+ SPL drivers.
+ The SPL driver only supports reading from the NAND using DMA
+ transfers.
+
+if NAND_SUNXI
+
+config NAND_SUNXI_SPL_ECC_STRENGTH
+ int "Allwinner NAND SPL ECC Strength"
+ default 64
+
+config NAND_SUNXI_SPL_ECC_SIZE
+ int "Allwinner NAND SPL ECC Step Size"
+ default 1024
+
+config NAND_SUNXI_SPL_USABLE_PAGE_SIZE
+ int "Allwinner NAND SPL Usable Page Size"
+ default 1024
+
+endif
+
+config NAND_ARASAN
+ bool "Configure Arasan Nand"
+ select SYS_NAND_SELF_INIT
+ imply CMD_NAND
+ help
+ This enables Nand driver support for Arasan nand flash
+ controller. This uses the hardware ECC for read and
+ write operations.
+
+config NAND_MXC
+ bool "MXC NAND support"
+ depends on CPU_ARM926EJS || CPU_ARM1136 || MX5
+ imply CMD_NAND
+ help
+ This enables the NAND driver for the NAND flash controller on the
+ i.MX27 / i.MX31 / i.MX5 rocessors.
+
+config NAND_MXS
+ bool "MXS NAND support"
+ depends on MX6 || MX7
+ imply CMD_NAND
+ help
+ This enables NAND driver for the NAND flash controller on the
+ MXS processors.
+
+config NAND_ZYNQ
+ bool "Support for Zynq Nand controller"
+ select SYS_NAND_SELF_INIT
+ imply CMD_NAND
+ help
+ This enables Nand driver support for Nand flash controller
+ found on Zynq SoC.
+
+config NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS
+ bool "Enable use of 1st stage bootloader timing for NAND"
+ depends on NAND_ZYNQ
+ help
+ This flag prevent U-boot reconfigure NAND flash controller and reuse
+ the NAND timing from 1st stage bootloader.
+
+comment "Generic NAND options"
+
+# Enhance depends when converting drivers to Kconfig which use this config
+# option (mxc_nand, ndfc, omap_gpmc).
+config SYS_NAND_BUSWIDTH_16BIT
+ bool "Use 16-bit NAND interface"
+ depends on NAND_VF610_NFC || NAND_OMAP_GPMC || NAND_MXC || ARCH_DAVINCI
+ help
+ Indicates that NAND device has 16-bit wide data-bus. In absence of this
+ config, bus-width of NAND device is assumed to be either 8-bit and later
+ determined by reading ONFI params.
+ Above config is useful when NAND device's bus-width information cannot
+ be determined from on-chip ONFI params, like in following scenarios:
+ - SPL boot does not support reading of ONFI parameters. This is done to
+ keep SPL code foot-print small.
+ - In current U-Boot flow using nand_init(), driver initialization
+ happens in board_nand_init() which is called before any device probe
+ (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are
+ not available while configuring controller. So a static CONFIG_NAND_xx
+ is needed to know the device's bus-width in advance.
+
projects / oweals / u-boot.git / blobdiff