usb: host: dwc3: Add support for multiple PHYs

[oweals/u-boot.git] / drivers / bootcount / Kconfig

diff --git a/drivers/bootcount/Kconfig b/drivers/bootcount/Kconfig
index 8c19ae610bb3493a9da6b49dcc41c7c6cd456e15..d335ed14b96172a5bbd29768546cf863d2f7bb8e 100644 (file)
--- a/drivers/bootcount/Kconfig
+++ b/drivers/bootcount/Kconfig
@@ -13,6 +13,17 @@ if BOOTCOUNT_LIMIT
 choice
        prompt "Boot count device"
        default BOOTCOUNT_AM33XX if AM33XX || SOC_DA8XX
 choice
        prompt "Boot count device"
        default BOOTCOUNT_AM33XX if AM33XX || SOC_DA8XX

+       default BOOTCOUNT_AT91 if AT91SAM9XE
+       default BOOTCOUNT_GENERIC
+
+config BOOTCOUNT_GENERIC
+       bool "Generic default boot counter"
+       help
+         Generic bootcount stored at SYS_BOOTCOUNT_ADDR.
+
+         SYS_BOOTCOUNT_ADDR:
+           Set to the address where the bootcount and bootcount magic
+           will be stored.

 
 config BOOTCOUNT_EXT
        bool "Boot counter on EXT filesystem"
 
 config BOOTCOUNT_EXT
        bool "Boot counter on EXT filesystem"


@@ -23,6 +34,7 @@ config BOOTCOUNT_EXT
 config BOOTCOUNT_AM33XX
        bool "Boot counter in AM33XX RTC IP block"
        depends on AM33XX || SOC_DA8XX
 config BOOTCOUNT_AM33XX
        bool "Boot counter in AM33XX RTC IP block"
        depends on AM33XX || SOC_DA8XX

+       select SPL_AM33XX_ENABLE_RTC32K_OSC if AM33XX

        help
          A bootcount driver for the RTC IP block found on many TI platforms.
          This requires the RTC clocks, etc, to be enabled prior to use and
        help
          A bootcount driver for the RTC IP block found on many TI platforms.
          This requires the RTC clocks, etc, to be enabled prior to use and


@@ -53,12 +65,24 @@ config BOOTCOUNT_I2C
          CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
          CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
                                      the bootcounter.
          CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
          CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
                                      the bootcounter.

-         CONFIG_BOOTCOUNT_ALEN = address len
+
+config BOOTCOUNT_AT91
+       bool "Boot counter for Atmel AT91SAM9XE"
+       depends on AT91SAM9XE

 
 endchoice
 
 
 endchoice
 

+config BOOTCOUNT_ALEN
+       int "I2C address length"
+       default 1
+       depends on BOOTCOUNT_I2C
+       help
+         Length of the the I2C address at SYS_BOOTCOUNT_ADDR for storing
+         the boot counter.
+

 config SYS_BOOTCOUNT_SINGLEWORD
        bool "Use single word to pack boot count and magic value"
 config SYS_BOOTCOUNT_SINGLEWORD
        bool "Use single word to pack boot count and magic value"

+       depends on BOOTCOUNT_GENERIC

        help
          This option enables packing boot count magic value and boot count
          into single word (32 bits).
        help
          This option enables packing boot count magic value and boot count
          into single word (32 bits).


@@ -88,8 +112,10 @@ config SYS_BOOTCOUNT_EXT_NAME
 
 config SYS_BOOTCOUNT_ADDR
        hex "RAM address used for reading and writing the boot counter"
 
 config SYS_BOOTCOUNT_ADDR
        hex "RAM address used for reading and writing the boot counter"

-       default 0x7000A000
-       depends on BOOTCOUNT_EXT
+       default 0x44E3E000 if BOOTCOUNT_AM33XX
+       default 0xE0115FF8 if ARCH_LS1043A || ARCH_LS1021A
+       depends on BOOTCOUNT_AM33XX || BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \
+                  BOOTCOUNT_I2C

        help
          Set the address used for reading and writing the boot counter.
 
        help
          Set the address used for reading and writing the boot counter.