-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- *((uint *)BCSR1) &= ~BCSR1_PCCEN;
- return 0;
-}
-#endif /* CFG_CMD_PCMCIA */
-
-#endif /* (F)ADS */
-
-/* -------------------------------------------------------------------- */
-/* TQM8xxL Boards by TQ Components */
-/* SC8xx Boards by SinoVee Microsystems */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx)
-
-#if defined(CONFIG_TQM8xxL)
-#define PCMCIA_BOARD_MSG "TQM8xxL"
-#endif
-#if defined(CONFIG_SVM_SC8xx)
-#define PCMCIA_BOARD_MSG "SC8xx"
-#endif
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(slot);
- pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
-#ifndef NSCU_OE_INV
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-#endif
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
-#ifndef CONFIG_HMI10
-#ifndef CONFIG_NSCU
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable
- */
- immap->im_ioport.iop_pcpar &= ~(0x0002 | 0x0004);
- immap->im_ioport.iop_pcso &= ~(0x0002 | 0x0004);
- /* remove all power */
-
- immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004);
-#endif
-#else /* CONFIG_HMI10 */
- /*
- * Configure Port B pins for
- * 5 Volts Enable and 3 Volts enable
- */
- immap->im_cpm.cp_pbpar &= ~(0x00000300);
-
- /* remove all power */
- immap->im_cpm.cp_pbdat |= 0x00000300;
-#endif /* CONFIG_HMI10 */
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-#ifndef CONFIG_HMI10
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-#else
- if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
-#endif /* CONFIG_HMI10 */
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
-#ifndef CONFIG_NSCU
- if ((reg & mask) == mask) {
-#ifndef CONFIG_HMI10
- immap->im_ioport.iop_pcdat |= 0x0004;
-#else
- immap->im_cpm.cp_pbdat &= ~(0x0000100);
-#endif /* CONFIG_HMI10 */
- puts (" 5.0V card found: ");
- } else {
-#ifndef CONFIG_HMI10
- immap->im_ioport.iop_pcdat |= 0x0002;
-#else
- immap->im_cpm.cp_pbdat &= ~(0x0000200);
-#endif /* CONFIG_HMI10 */
- puts (" 3.3V card found: ");
- }
-#ifndef CONFIG_HMI10
- immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004);
-#else
- immap->im_cpm.cp_pbdir |= 0x00000300;
-#endif /* CONFIG_HMI10 */
-#else
- if ((reg & mask) == mask) {
- puts (" 5.0V card found: ");
- } else {
- puts (" 3.3V card found: ");
- }
-#endif
-#if 0
- /* VCC switch error flag, PCMCIA slot INPACK_ pin */
- cp->cp_pbdir &= ~(0x0020 | 0x0010);
- cp->cp_pbpar &= ~(0x0020 | 0x0010);
- udelay(500000);
-#endif
- udelay(1000);
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
-#ifndef NSCU_OE_INV
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
-#else
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-#endif
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
-#ifndef CONFIG_HMI10
-#ifndef CONFIG_NSCU
- /* remove all power */
- immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004);
-#endif
-#else /* CONFIG_HMI10 */
- immap->im_cpm.cp_pbdat |= 0x00000300;
-#endif /* CONFIG_HMI10 */
-
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
-#ifndef NSCU_OE_INV
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-#endif
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-#ifdef CONFIG_NSCU
-static int voltage_set(int slot, int vcc, int vpp)
-{
- return 0;
-}
-#else
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
-#ifndef NSCU_OE_INV
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-#else
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
-#endif
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
-#ifndef CONFIG_HMI10
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn off all power
- */
- debug ("PCMCIA power OFF\n");
- immap->im_ioport.iop_pcpar &= ~(0x0002 | 0x0004);
- immap->im_ioport.iop_pcso &= ~(0x0002 | 0x0004);
- immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004);
-
- reg = 0;
- switch(vcc) {
- case 0: break;
- case 33: reg |= 0x0002; break;
- case 50: reg |= 0x0004; break;
- default: goto done;
- }
-#else /* CONFIG_HMI10 */
- /*
- * Configure Port B pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn off all power
- */
- debug ("PCMCIA power OFF\n");
- immap->im_cpm.cp_pbpar &= ~(0x00000300);
- /* remove all power */
-
- immap->im_cpm.cp_pbdat |= 0x00000300;
-
- reg = 0;
- switch(vcc) {
- case 0: break;
- case 33: reg |= 0x00000200; break;
- case 50: reg |= 0x00000100; break;
- default: goto done;
-}
-#endif /* CONFIG_HMI10 */
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-#ifndef CONFIG_HMI10
- immap->im_ioport.iop_pcdat |= reg;
- immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004);
-#else
- immap->im_cpm.cp_pbdat &= !reg;
- immap->im_cpm.cp_pbdir |= 0x00000300;
-#endif /* CONFIG_HMI10 */
- if (reg) {
-#ifndef CONFIG_HMI10
- debug ("PCMCIA powered at %sV\n",
- (reg&0x0004) ? "5.0" : "3.3");
-#else
- debug ("PCMCIA powered at %sV\n",
- (reg&0x00000200) ? "5.0" : "3.3");
-#endif /* CONFIG_HMI10 */
- } else {
- debug ("PCMCIA powered down\n");
- }
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
-#ifndef NSCU_OE_INV
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
-#else
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-#endif
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-#endif
-
-#endif /* TQM8xxL */
-
-
-/* -------------------------------------------------------------------- */
-/* LWMON Board */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_LWMON)
-
-#define PCMCIA_BOARD_MSG "LWMON"
-
-/* #define's for MAX1604 Power Switch */
-#define MAX1604_OP_SUS 0x80
-#define MAX1604_VCCBON 0x40
-#define MAX1604_VCC_35 0x20
-#define MAX1604_VCCBHIZ 0x10
-#define MAX1604_VPPBON 0x08
-#define MAX1604_VPPBPBPGM 0x04
-#define MAX1604_VPPBHIZ 0x02
-/* reserved 0x01 */
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
- uchar val;
-
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- /* Switch on PCMCIA port in PIC register 0x60 */
- reg = pic_read (0x60);
- debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
- reg &= ~0x10;
- /* reg |= 0x08; Vpp not needed */
- pic_write (0x60, reg);
-#ifdef DEBUG
- reg = pic_read (0x60);
- printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
-#endif
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
- if ((reg & mask) == mask) {
- val = 0; /* VCCB3/5 = 0 ==> use Vx = 5.0 V */
- puts (" 5.0V card found: ");
- } else {
- val = MAX1604_VCC_35; /* VCCB3/5 = 1 ==> use Vy = 3.3 V */
- puts (" 3.3V card found: ");
- }
-
- /* switch VCC on */
- val |= MAX1604_OP_SUS | MAX1604_VCCBON;
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
- i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
- udelay(500000);
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
- uchar val;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* remove all power, put output in high impedance state */
- val = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
- i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- /* Switch off PCMCIA port in PIC register 0x60 */
- reg = pic_read (0x60);
- debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
- reg |= 0x10;
- reg &= ~0x08;
- pic_write (0x60, reg);
-#ifdef DEBUG
- reg = pic_read (0x60);
- printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
-#endif
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
- uchar val;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Turn off all power (switch to high impedance)
- */
- debug ("PCMCIA power OFF\n");
- val = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
- i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
- val = 0;
- switch(vcc) {
- case 0: break;
- case 33: val = MAX1604_VCC_35; break;
- case 50: break;
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
- if (val) {
- debug ("PCMCIA powered at %sV\n",
- (val & MAX1604_VCC_35) ? "3.3" : "5.0");
- } else {
- debug ("PCMCIA powered down\n");
- }
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-#endif /* LWMON */
-
-/* -------------------------------------------------------------------- */
-/* GTH board by Corelatus AB */
-/* -------------------------------------------------------------------- */
-#if defined(CONFIG_GTH)
-
-#define PCMCIA_BOARD_MSG "GTH COMPACT FLASH"
-
-static int voltage_set (int slot, int vcc, int vpp)
-{ /* Do nothing */
- return 0;
-}
-
-static int hardware_enable (int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: GTH Slot %c\n", 'A' + slot);
-
- immap = (immap_t *) CFG_IMMR;
- sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX (_slot_) = reg;
- udelay (500);
-
- /*
- * Make sure there is a card in the slot,
- * then configure the interface.
- */
- udelay (10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__, __FUNCTION__,
- &(pcmp->pcmc_pipr), pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & 0x98000000) {
- printf (" No Card found\n");
- return (1);
- }
-
- mask = PCMCIA_VS1 (slot) | PCMCIA_VS2 (slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
- (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX (_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX (_slot_) = reg;
-
- udelay (250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return 0;
-}
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- return 0; /* No hardware to disable */
-}
-#endif /* CFG_CMD_PCMCIA */
-#endif /* CONFIG_GTH */
-
-/* -------------------------------------------------------------------- */
-/* ICU862 Boards by Cambridge Broadband Ltd. */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ICU862)
-
-#define PCMCIA_BOARD_MSG "ICU862"
-
-static void cfg_port_B (void);
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, pipr, mask;
- int i;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /* Configure Port B for TPS2205 PC-Card Power-Interface Switch */
- cfg_port_B ();
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- pipr = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- pipr,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
-
- reg = cp->cp_pbdat;
- if ((pipr & mask) == mask) {
- reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
- TPS2205_VCC3); /* 3V off */
- reg &= ~(TPS2205_VCC5); /* 5V on */
- puts (" 5.0V card found: ");
- } else {
- reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
- TPS2205_VCC5); /* 5V off */
- reg &= ~(TPS2205_VCC3); /* 3V on */
- puts (" 3.3V card found: ");
- }
-
- debug ("\nPB DAT: %08x -> 3.3V %s 5.0V %s VPP_PGM %s VPP_VCC %s\n",
- reg,
- (reg & TPS2205_VCC3) ? "off" : "on",
- (reg & TPS2205_VCC5) ? "off" : "on",
- (reg & TPS2205_VPP_PGM) ? "off" : "on",
- (reg & TPS2205_VPP_VCC) ? "off" : "on" );
-
- cp->cp_pbdat = reg;
-
- /* Wait 500 ms; use this to check for over-current */
- for (i=0; i<5000; ++i) {
- if ((cp->cp_pbdat & TPS2205_OC) == 0) {
- printf (" *** Overcurrent - Safety shutdown ***\n");
- cp->cp_pbdat &= ~(TPS2205_SHDN);
- return (1);
- }
- udelay (100);
- }
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* Shut down */
- cp->cp_pbdat &= ~(TPS2205_SHDN);
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn all power pins to Hi-Z
- */
- debug ("PCMCIA power OFF\n");
- cfg_port_B (); /* Enables switch, but all in Hi-Z */
-
- reg = cp->cp_pbdat;
-
- switch(vcc) {
- case 0: break; /* Switch off */
- case 33: reg &= ~TPS2205_VCC3; break; /* Switch on 3.3V */
- case 50: reg &= ~TPS2205_VCC5; break; /* Switch on 5.0V */
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- cp->cp_pbdat = reg;
-
-#ifdef DEBUG
- {
- char *s;
-
- if ((reg & TPS2205_VCC3) == 0) {
- s = "at 3.3V";
- } else if ((reg & TPS2205_VCC5) == 0) {
- s = "at 5.0V";
- } else {
- s = "down";
- }
- printf ("PCMCIA powered %s\n", s);
- }
-#endif
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-static void cfg_port_B (void)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- uint reg;
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure Port B for TPS2205 PC-Card Power-Interface Switch
- *
- * Switch off all voltages, assert shutdown
- */
- reg = cp->cp_pbdat;
- reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
- TPS2205_VCC3 | TPS2205_VCC5 | /* VAVCC => Hi-Z */
- TPS2205_SHDN); /* enable switch */
- cp->cp_pbdat = reg;
-
- cp->cp_pbpar &= ~(TPS2205_INPUTS | TPS2205_OUTPUTS);
-
- reg = cp->cp_pbdir & ~(TPS2205_INPUTS);
- cp->cp_pbdir = reg | TPS2205_OUTPUTS;
-
- debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
- cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
-}
-
-#endif /* ICU862 */
-
-
-/* -------------------------------------------------------------------- */
-/* C2MON Boards by TTTech Computertechnik AG */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_C2MON)
-
-#define PCMCIA_BOARD_MSG "C2MON"
-
-static void cfg_ports (void);
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, pipr, mask;
- ushort sreg;
- int i;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
- cfg_ports ();
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- pipr = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- pipr,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
-
- sreg = immap->im_ioport.iop_pcdat;
- if ((pipr & mask) == mask) {
- sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1 | /* VAVPP => Hi-Z */
- TPS2211_VCCD1); /* 5V on */
- sreg &= ~(TPS2211_VCCD0); /* 3V off */
- puts (" 5.0V card found: ");
- } else {
- sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1 | /* VAVPP => Hi-Z */
- TPS2211_VCCD0); /* 3V on */
- sreg &= ~(TPS2211_VCCD1); /* 5V off */
- puts (" 3.3V card found: ");
- }
-
- debug ("\nPC DAT: %04x -> 3.3V %s 5.0V %s\n",
- sreg,
- ( (sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) ? "on" : "off",
- (!(sreg & TPS2211_VCCD0) && (sreg & TPS2211_VCCD1)) ? "on" : "off"
- );
-
- immap->im_ioport.iop_pcdat = sreg;
-
- /* Wait 500 ms; use this to check for over-current */
- for (i=0; i<5000; ++i) {
- if ((cp->cp_pbdat & TPS2211_OC) == 0) {
- printf (" *** Overcurrent - Safety shutdown ***\n");
- immap->im_ioport.iop_pcdat &= ~(TPS2211_VCCD0|TPS2211_VCCD1);
- return (1);
- }
- udelay (100);
- }
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- /* ALl voltages off / Hi-Z */
- immap->im_ioport.iop_pcdat |= (TPS2211_VPPD0 | TPS2211_VPPD1 |
- TPS2211_VCCD0 | TPS2211_VCCD1 );
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
- ushort sreg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn all power pins to Hi-Z
- */
- debug ("PCMCIA power OFF\n");
- cfg_ports (); /* Enables switch, but all in Hi-Z */
-
- sreg = immap->im_ioport.iop_pcdat;
- sreg |= TPS2211_VPPD0 | TPS2211_VPPD1; /* VAVPP always Hi-Z */
-
- switch(vcc) {
- case 0: break; /* Switch off */
- case 33: sreg |= TPS2211_VCCD0; /* Switch on 3.3V */
- sreg &= ~TPS2211_VCCD1;
- break;
- case 50: sreg &= ~TPS2211_VCCD0; /* Switch on 5.0V */
- sreg |= TPS2211_VCCD1;
- break;
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- immap->im_ioport.iop_pcdat = sreg;
-
-#ifdef DEBUG
- {
- char *s;
-
- if ((sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) {
- s = "at 3.3V";
- } else if (!(sreg & TPS2211_VCCD0) && (sreg & TPS2211_VCCD1)) {
- s = "at 5.0V";
- } else {
- s = "down";
- }
- printf ("PCMCIA powered %s\n", s);
- }
-#endif
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-static void cfg_ports (void)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- ushort sreg;
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure Port C for TPS2211 PC-Card Power-Interface Switch
- *
- * Switch off all voltages, assert shutdown
- */
- sreg = immap->im_ioport.iop_pcdat;
- sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1); /* VAVPP => Hi-Z */
- sreg &= ~(TPS2211_VCCD0 | TPS2211_VCCD1); /* 3V and 5V off */
- immap->im_ioport.iop_pcdat = sreg;
-
- immap->im_ioport.iop_pcpar &= ~(TPS2211_OUTPUTS);
- immap->im_ioport.iop_pcdir |= TPS2211_OUTPUTS;
-
- debug ("Set Port C: PAR: %04x DIR: %04x DAT: %04x\n",
- immap->im_ioport.iop_pcpar,
- immap->im_ioport.iop_pcdir,
- immap->im_ioport.iop_pcdat);
-
- /*
- * Configure Port B for TPS2211 PC-Card Power-Interface Switch
- *
- * Over-Current Input only
- */
- cp->cp_pbpar &= ~(TPS2211_INPUTS);
- cp->cp_pbdir &= ~(TPS2211_INPUTS);
-
- debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
- cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
-}
-
-#endif /* C2MON */
-
-/* -------------------------------------------------------------------- */
-/* MBX board from Morotola */
-/* -------------------------------------------------------------------- */
-
-#if defined( CONFIG_MBX )
-#include <../board/mbx8xx/csr.h>
-
-/* A lot of this has been taken from the RPX code in this file it works from me.
- I have added the voltage selection for the MBX board. */
-
-/* MBX voltage bit in control register #2 */
-#define CR2_VPP12 ((uchar)0x10)
-#define CR2_VPPVDD ((uchar)0x20)
-#define CR2_VDD5 ((uchar)0x40)
-#define CR2_VDD3 ((uchar)0x80)
-
-#define PCMCIA_BOARD_MSG "MBX860"
-
-static int voltage_set (int slot, int vcc, int vpp)
-{
- uchar reg = 0;
-
- debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10);
-
- switch (vcc) {
- case 0:
- break;
- case 33:
- reg |= CR2_VDD3;
- break;
- case 50:
- reg |= CR2_VDD5;
- break;
- default:
- return 1;
- }
-
- switch (vpp) {
- case 0:
- break;
- case 33:
- case 50:
- if (vcc == vpp) {
- reg |= CR2_VPPVDD;
- } else {
- return 1;
- }
- break;
- case 120:
- reg |= CR2_VPP12;
- break;
- default:
- return 1;
- }
-
- /* first, turn off all power */
- MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL);
-
- /* enable new powersettings */
- MBX_CSR2 |= reg;
- debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2);
-
- return (0);
-}
-
-static int hardware_enable (int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n",
- 'A' + slot);
-
- udelay (10000);
-
- immap = (immap_t *) CFG_IMMR;
- sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX (_slot_) = reg;
- udelay (500);
-
- /* remove all power */
- voltage_set (slot, 0, 0);
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-#ifndef CONFIG_HMI10
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-#else
- if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
-#endif /* CONFIG_HMI10 */
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
- (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
- (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
-
- if ((reg & mask) == mask) {
- voltage_set (_slot_, 50, 0);
- printf (" 5.0V card found: ");
- } else {
- voltage_set (_slot_, 33, 0);
- printf (" 3.3V card found: ");
- }
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX (_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX (_slot_) = reg;
-
- udelay (250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable (int slot)
-{
- return 0; /* No hardware to disable */
-}
-#endif /* CFG_CMD_PCMCIA */
-#endif /* CONFIG_MBX */
-/* -------------------------------------------------------------------- */
-/* R360MPI Board */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_R360MPI)
-
-#define PCMCIA_BOARD_MSG "R360MPI"
-
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Ports A, B & C pins for
- * 5 Volts Enable and 3 Volts enable
- */
- immap->im_ioport.iop_pcpar &= ~(0x0400);
- immap->im_ioport.iop_pcso &= ~(0x0400);/*
- immap->im_ioport.iop_pcdir |= 0x0400;*/
-
- immap->im_ioport.iop_papar &= ~(0x0200);/*
- immap->im_ioport.iop_padir |= 0x0200;*/
-#if 0
- immap->im_ioport.iop_pbpar &= ~(0xC000);
- immap->im_ioport.iop_pbdir &= ~(0xC000);
-#endif
- /* remove all power */
-
- immap->im_ioport.iop_pcdat |= 0x0400;
- immap->im_ioport.iop_padat |= 0x0200;
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
- if ((reg & mask) == mask) {
- immap->im_ioport.iop_pcdat &= ~(0x4000);
- puts (" 5.0V card found: ");
- } else {
- immap->im_ioport.iop_padat &= ~(0x0002);
- puts (" 3.3V card found: ");
- }
- immap->im_ioport.iop_pcdir |= 0x0400;
- immap->im_ioport.iop_padir |= 0x0200;
-#if 0
- /* VCC switch error flag, PCMCIA slot INPACK_ pin */
- cp->cp_pbdir &= ~(0x0020 | 0x0010);
- cp->cp_pbpar &= ~(0x0020 | 0x0010);
- udelay(500000);
-#endif
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* remove all power */
- immap->im_ioport.iop_pcdat |= 0x0400;
- immap->im_ioport.iop_padat |= 0x0200;
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Ports A & C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn off all power
- */
- debug ("PCMCIA power OFF\n");
- immap->im_ioport.iop_pcpar &= ~(0x0400);
- immap->im_ioport.iop_pcso &= ~(0x0400);/*
- immap->im_ioport.iop_pcdir |= 0x0400;*/
-
- immap->im_ioport.iop_papar &= ~(0x0200);/*
- immap->im_ioport.iop_padir |= 0x0200;*/
-
- immap->im_ioport.iop_pcdat |= 0x0400;
- immap->im_ioport.iop_padat |= 0x0200;
-
- reg = 0;
- switch(vcc) {
- case 0: break;
- case 33: reg |= 0x0200; break;
- case 50: reg |= 0x0400; break;
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- if (reg & 0x0200)
- immap->im_ioport.iop_pcdat &= !reg;
- if (reg & 0x0400)
- immap->im_ioport.iop_padat &= !reg;
- immap->im_ioport.iop_pcdir |= 0x0200;
- immap->im_ioport.iop_padir |= 0x0400;
- if (reg) {
- debug ("PCMCIA powered at %sV\n",
- (reg&0x0400) ? "5.0" : "3.3");
- } else {
- debug ("PCMCIA powered down\n");
- }
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-#endif /* R360MPI */
-
-/* -------------------------------------------------------------------- */
-/* KUP4K and KUP4X Boards */
-/* -------------------------------------------------------------------- */
-#if defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
-
-#define PCMCIA_BOARD_MSG "KUP"
-
-#define KUP4K_PCMCIA_B_3V3 (0x00020000)
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(slot);
- pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(slot) = reg;
- udelay(2500);
-
- /*
- * Configure Port B pins for
- * 3 Volts enable
- */
- if (slot) { /* Slot A is built-in */
- cp->cp_pbdir |= KUP4K_PCMCIA_B_3V3;
- cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
- /* remove all power */
- cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3; /* active low */
- }
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- printf("%s Slot %c:", slot ? "" : "\n", 'A' + slot);
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
- if ((reg & mask) == mask) {
- puts (" 5.0V card found: NOT SUPPORTED !!!\n");
- } else {
- if(slot)
- cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
- puts (" 3.3V card found: ");
- }
-#if 0
- /* VCC switch error flag, PCMCIA slot INPACK_ pin */
- cp->cp_pbdir &= ~(0x0020 | 0x0010);
- cp->cp_pbpar &= ~(0x0020 | 0x0010);
- udelay(500000);
-#endif
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /* remove all power */
- if (slot)
- cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3;
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: " \
- PCMCIA_BOARD_MSG \
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- if (!slot) /* Slot A is not configurable */
- return 0;
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- debug ("PCMCIA power OFF\n");
- /*
- * Configure Port B pins for
- * 3 Volts enable
- */
- cp->cp_pbdir |= KUP4K_PCMCIA_B_3V3;
- cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
- /* remove all power */
- cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3; /* active low */
-
- switch(vcc) {
- case 0: break;
- case 33:
- cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
- debug ("PCMCIA powered at 3.3V\n");
- break;
- case 50:
- debug ("PCMCIA: 5Volt vcc not supported\n");
- break;
- default:
- puts("PCMCIA: vcc not supported");
- break;
- }
- udelay(10000);
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & (0x80000000 >> (slot << 4)))
- ? "only 5 V --> NOT SUPPORTED"
- : "can do 3.3V");
-
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-#endif /* KUP4K || KUP4X */
-
-
-/* -------------------------------------------------------------------- */
-/* End of Board Specific Stuff */
-/* -------------------------------------------------------------------- */
-
-
-/* -------------------------------------------------------------------- */
-/* MPC8xx Specific Stuff - should go to MPC8xx directory */
-/* -------------------------------------------------------------------- */
-
-/*
- * Search this table to see if the windowsize is
- * supported...
- */
-
-#define M8XX_SIZES_NO 32
-
-static const u_int m8xx_size_to_gray[M8XX_SIZES_NO] =
-{ 0x00000001, 0x00000002, 0x00000008, 0x00000004,
- 0x00000080, 0x00000040, 0x00000010, 0x00000020,
- 0x00008000, 0x00004000, 0x00001000, 0x00002000,
- 0x00000100, 0x00000200, 0x00000800, 0x00000400,
-
- 0x0fffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- 0x01000000, 0x02000000, 0xffffffff, 0x04000000,
- 0x00010000, 0x00020000, 0x00080000, 0x00040000,
- 0x00800000, 0x00400000, 0x00100000, 0x00200000 };
-
-
-/* -------------------------------------------------------------------- */
-
-#if ( ! defined(CONFIG_I82365) && ! defined(CONFIG_PXA_PCMCIA) )
-
-static u_int m8xx_get_graycode(u_int size)
-{
- u_int k;
-
- for (k = 0; k < M8XX_SIZES_NO; k++) {
- if(m8xx_size_to_gray[k] == size)
- break;
- }
-
- if((k == M8XX_SIZES_NO) || (m8xx_size_to_gray[k] == -1))
- k = -1;
-
- return k;
-}
-
-#endif /* CONFIG_I82365 */
-
-/* -------------------------------------------------------------------- */
-
-#if 0
-static u_int m8xx_get_speed(u_int ns, u_int is_io)
-{
- u_int reg, clocks, psst, psl, psht;
-
- if(!ns) {
-
- /*
- * We get called with IO maps setup to 0ns
- * if not specified by the user.
- * They should be 255ns.
- */
-
- if(is_io)
- ns = 255;
- else
- ns = 100; /* fast memory if 0 */
- }
-
- /*
- * In PSST, PSL, PSHT fields we tell the controller
- * timing parameters in CLKOUT clock cycles.
- * CLKOUT is the same as GCLK2_50.
- */
-
-/* how we want to adjust the timing - in percent */
-
-#define ADJ 180 /* 80 % longer accesstime - to be sure */
-
- clocks = ((M8XX_BUSFREQ / 1000) * ns) / 1000;
- clocks = (clocks * ADJ) / (100*1000);
-
- if(clocks >= PCMCIA_BMT_LIMIT) {
- DEBUG(0, "Max access time limit reached\n");
- clocks = PCMCIA_BMT_LIMIT-1;
- }
-
- psst = clocks / 7; /* setup time */
- psht = clocks / 7; /* hold time */
- psl = (clocks * 5) / 7; /* strobe length */
-
- psst += clocks - (psst + psht + psl);
-
- reg = psst << 12;
- reg |= psl << 7;
- reg |= psht << 16;
-
- return reg;
-}
-#endif
-
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
-static void print_funcid (int func)
-{
- puts (indent);
- switch (func) {
- case CISTPL_FUNCID_MULTI:
- puts (" Multi-Function");
- break;
- case CISTPL_FUNCID_MEMORY:
- puts (" Memory");
- break;
- case CISTPL_FUNCID_SERIAL:
- puts (" Serial Port");
- break;
- case CISTPL_FUNCID_PARALLEL:
- puts (" Parallel Port");
- break;
- case CISTPL_FUNCID_FIXED:
- puts (" Fixed Disk");
- break;
- case CISTPL_FUNCID_VIDEO:
- puts (" Video Adapter");
- break;
- case CISTPL_FUNCID_NETWORK:
- puts (" Network Adapter");
- break;
- case CISTPL_FUNCID_AIMS:
- puts (" AIMS Card");
- break;
- case CISTPL_FUNCID_SCSI:
- puts (" SCSI Adapter");
- break;
- default:
- puts (" Unknown");
- break;
- }
- puts (" Card\n");
-}
-#endif /* CONFIG_IDE_8xx_PCCARD */
-
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
-static void print_fixed (volatile uchar *p)
-{
- if (p == NULL)
- return;
-
- puts(indent);
-
- switch (*p) {
- case CISTPL_FUNCE_IDE_IFACE:
- { uchar iface = *(p+2);
-
- puts ((iface == CISTPL_IDE_INTERFACE) ? " IDE" : " unknown");
- puts (" interface ");
- break;
- }
- case CISTPL_FUNCE_IDE_MASTER:
- case CISTPL_FUNCE_IDE_SLAVE:
- { uchar f1 = *(p+2);
- uchar f2 = *(p+4);
-
- puts ((f1 & CISTPL_IDE_SILICON) ? " [silicon]" : " [rotating]");
-
- if (f1 & CISTPL_IDE_UNIQUE)
- puts (" [unique]");
-
- puts ((f1 & CISTPL_IDE_DUAL) ? " [dual]" : " [single]");
-
- if (f2 & CISTPL_IDE_HAS_SLEEP)
- puts (" [sleep]");
-
- if (f2 & CISTPL_IDE_HAS_STANDBY)
- puts (" [standby]");
-
- if (f2 & CISTPL_IDE_HAS_IDLE)
- puts (" [idle]");
-
- if (f2 & CISTPL_IDE_LOW_POWER)
- puts (" [low power]");
-
- if (f2 & CISTPL_IDE_REG_INHIBIT)
- puts (" [reg inhibit]");
-
- if (f2 & CISTPL_IDE_HAS_INDEX)
- puts (" [index]");
-
- if (f2 & CISTPL_IDE_IOIS16)
- puts (" [IOis16]");
-
- break;
- }
- }
- putc ('\n');
-}
-#endif /* CONFIG_IDE_8xx_PCCARD */
-
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
-
-#define MAX_IDENT_CHARS 64
-#define MAX_IDENT_FIELDS 4
-
-static uchar *known_cards[] = {
- "ARGOSY PnPIDE D5",
- NULL
-};
-
-static int identify (volatile uchar *p)
-{
- uchar id_str[MAX_IDENT_CHARS];
- uchar data;
- uchar *t;
- uchar **card;
- int i, done;
-
- if (p == NULL)
- return (0); /* Don't know */
-
- t = id_str;
- done =0;
-
- for (i=0; i<=4 && !done; ++i, p+=2) {
- while ((data = *p) != '\0') {
- if (data == 0xFF) {
- done = 1;
- break;
- }
- *t++ = data;
- if (t == &id_str[MAX_IDENT_CHARS-1]) {
- done = 1;
- break;
- }
- p += 2;
- }
- if (!done)
- *t++ = ' ';
- }
- *t = '\0';
- while (--t > id_str) {
- if (*t == ' ')
- *t = '\0';
- else
- break;
- }
- puts (id_str);
- putc ('\n');
-
- for (card=known_cards; *card; ++card) {
- debug ("## Compare against \"%s\"\n", *card);
- if (strcmp(*card, id_str) == 0) { /* found! */
- debug ("## CARD FOUND ##\n");
- return (1);
- }
- }
-
- return (0); /* don't know */
-}
-#endif /* CONFIG_IDE_8xx_PCCARD */
-
-/* -------------------------------------------------------------------- */
-/* NETTA board by Intracom S.A. */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_NETTA)
-
-/* some sane bit macros */
-#define _BD(_b) (1U << (31-(_b)))
-#define _BDR(_l, _h) (((((1U << (31-(_l))) - 1) << 1) | 1) & ~((1U << (31-(_h))) - 1))
-
-#define _BW(_b) (1U << (15-(_b)))
-#define _BWR(_l, _h) (((((1U << (15-(_l))) - 1) << 1) | 1) & ~((1U << (15-(_h))) - 1))
-
-#define _BB(_b) (1U << (7-(_b)))
-#define _BBR(_l, _h) (((((1U << (7-(_l))) - 1) << 1) | 1) & ~((1U << (7-(_h))) - 1))
-
-#define _B(_b) _BD(_b)
-#define _BR(_l, _h) _BDR(_l, _h)
-
-#define PCMCIA_BOARD_MSG "NETTA"
-
-static const unsigned short vppd_masks[2] = { _BW(14), _BW(15) };
-
-static void cfg_vppd(int no)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
- return;
-
- mask = vppd_masks[no];
-
- immap->im_ioport.iop_papar &= ~mask;
- immap->im_ioport.iop_paodr &= ~mask;
- immap->im_ioport.iop_padir |= mask;
-}
-
-static void set_vppd(int no, int what)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
- return;
-
- mask = vppd_masks[no];
-
- if (what)
- immap->im_ioport.iop_padat |= mask;
- else
- immap->im_ioport.iop_padat &= ~mask;
-}
-
-static const unsigned short vccd_masks[2] = { _BW(10), _BW(6) };
-
-static void cfg_vccd(int no)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
- return;
-
- mask = vccd_masks[no];
-
- immap->im_ioport.iop_papar &= ~mask;
- immap->im_ioport.iop_paodr &= ~mask;
- immap->im_ioport.iop_padir |= mask;
-}
-
-static void set_vccd(int no, int what)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
- return;
-
- mask = vccd_masks[no];
-
- if (what)
- immap->im_ioport.iop_padat |= mask;
- else
- immap->im_ioport.iop_padat &= ~mask;
-}
-
-static const unsigned short oc_mask = _BW(8);
-
-static void cfg_oc(void)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask = oc_mask;
-
- immap->im_ioport.iop_pcdir &= ~mask;
- immap->im_ioport.iop_pcso &= ~mask;
- immap->im_ioport.iop_pcint &= ~mask;
- immap->im_ioport.iop_pcpar &= ~mask;
-}
-
-static int get_oc(void)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask = oc_mask;
- int what;
-
- what = !!(immap->im_ioport.iop_pcdat & mask);;
- return what;
-}
-
-static const unsigned short shdn_mask = _BW(12);
-
-static void cfg_shdn(void)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- mask = shdn_mask;
-
- immap->im_ioport.iop_papar &= ~mask;
- immap->im_ioport.iop_paodr &= ~mask;
- immap->im_ioport.iop_padir |= mask;
-}
-
-static void set_shdn(int what)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- mask = shdn_mask;
-
- if (what)
- immap->im_ioport.iop_padat |= mask;
- else
- immap->im_ioport.iop_padat &= ~mask;
-}
-
-static void cfg_ports (void);
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, pipr, mask;
- int i;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
- cfg_ports ();
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- pipr = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- pipr,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
-
- if ((pipr & mask) == mask) {
- set_vppd(0, 1); set_vppd(1, 1); /* VAVPP => Hi-Z */
- set_vccd(0, 0); set_vccd(1, 1); /* 5V on, 3V off */
- puts (" 5.0V card found: ");
- } else {
- set_vppd(0, 1); set_vppd(1, 1); /* VAVPP => Hi-Z */
- set_vccd(0, 1); set_vccd(1, 0); /* 5V off, 3V on */
- puts (" 3.3V card found: ");
- }
-
- /* Wait 500 ms; use this to check for over-current */
- for (i=0; i<5000; ++i) {
- if (!get_oc()) {
- printf (" *** Overcurrent - Safety shutdown ***\n");
- set_vccd(0, 0); set_vccd(1, 0); /* VAVPP => Hi-Z */
- return (1);
- }
- udelay (100);
- }
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- /* All voltages off / Hi-Z */
- set_vppd(0, 1); set_vppd(1, 1);
- set_vccd(0, 1); set_vccd(1, 1);
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
- ushort sreg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn all power pins to Hi-Z
- */
- debug ("PCMCIA power OFF\n");
- cfg_ports (); /* Enables switch, but all in Hi-Z */
-
- sreg = immap->im_ioport.iop_pcdat;
- set_vppd(0, 1); set_vppd(1, 1);
-
- switch(vcc) {
- case 0:
- break; /* Switch off */
-
- case 33:
- set_vccd(0, 1); set_vccd(1, 0);
- break;
-
- case 50:
- set_vccd(0, 0); set_vccd(1, 1);
- break;
-
- default:
- goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-static void cfg_ports (void)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-
- cfg_vppd(0); cfg_vppd(1); /* VPPD0,VPPD1 VAVPP => Hi-Z */
- cfg_vccd(0); cfg_vccd(1); /* 3V and 5V off */
- cfg_shdn();
- cfg_oc();
-
- /*
- * Configure Port A for TPS2211 PC-Card Power-Interface Switch
- *
- * Switch off all voltages, assert shutdown
- */
- set_vppd(0, 1); set_vppd(1, 1);
- set_vccd(0, 0); set_vccd(1, 0);
- set_shdn(1);
-
- udelay(100000);
-}
-
-#endif /* NETTA */
-
-
-/* -------------------------------------------------------------------- */
-
-#endif /* CFG_CMD_PCMCIA || (CFG_CMD_IDE && CONFIG_IDE_8xx_PCCARD) */
-
-/**************************************************/
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-U_BOOT_CMD(
- pinit, 2, 1, do_pinit,
- "pinit - PCMCIA sub-system\n",
- "on - power on PCMCIA socket\n"
- "pinit off - power off PCMCIA socket\n"
-);
-#endif