-int print_cpuinfo (void);
-
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-init_fnc_t *init_sequence[] = {
-#if defined(CONFIG_ARCH_CPU_INIT)
- arch_cpu_init, /* basic arch cpu dependent setup */
-#endif
- board_init, /* basic board dependent setup */
-#if defined(CONFIG_USE_IRQ)
- interrupt_init, /* set up exceptions */
-#endif
- timer_init, /* initialize timer */
-#ifdef CONFIG_FSL_ESDHC
- get_clocks,
-#endif
- env_init, /* initialize environment */
- init_baudrate, /* initialze baudrate settings */
- serial_init, /* serial communications setup */
- console_init_f, /* stage 1 init of console */
- display_banner, /* say that we are here */
-#if defined(CONFIG_DISPLAY_CPUINFO)
- print_cpuinfo, /* display cpu info (and speed) */
-#endif
-#if defined(CONFIG_DISPLAY_BOARDINFO)
- checkboard, /* display board info */
-#endif
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
- init_func_i2c,
-#endif
- dram_init, /* configure available RAM banks */
-#if defined(CONFIG_CMD_PCI) || defined (CONFIG_PCI)
- arm_pci_init,
-#endif
- display_dram_config,
- NULL,
-};
-
-void start_armboot (void)
-{
- init_fnc_t **init_fnc_ptr;
- char *s;
-#if defined(CONFIG_VFD) || defined(CONFIG_LCD)
- unsigned long addr;
-#endif
-
- /* Pointer is writable since we allocated a register for it */
- gd = (gd_t*)(_armboot_start - CONFIG_SYS_MALLOC_LEN - sizeof(gd_t));
- /* compiler optimization barrier needed for GCC >= 3.4 */
- __asm__ __volatile__("": : :"memory");
-
- memset ((void*)gd, 0, sizeof (gd_t));
- gd->bd = (bd_t*)((char*)gd - sizeof(bd_t));
- memset (gd->bd, 0, sizeof (bd_t));
-
- gd->flags |= GD_FLG_RELOC;
-
- monitor_flash_len = _bss_start - _armboot_start;
-
- for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {
- if ((*init_fnc_ptr)() != 0) {
- hang ();
- }
- }
-
- /* armboot_start is defined in the board-specific linker script */
- mem_malloc_init (_armboot_start - CONFIG_SYS_MALLOC_LEN,
- CONFIG_SYS_MALLOC_LEN);
-
-#ifndef CONFIG_SYS_NO_FLASH
- /* configure available FLASH banks */
- display_flash_config (flash_init ());
-#endif /* CONFIG_SYS_NO_FLASH */
-
-#ifdef CONFIG_VFD
-# ifndef PAGE_SIZE
-# define PAGE_SIZE 4096
-# endif
- /*
- * reserve memory for VFD display (always full pages)
- */
- /* bss_end is defined in the board-specific linker script */
- addr = (_bss_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
- vfd_setmem (addr);
- gd->fb_base = addr;
-#endif /* CONFIG_VFD */
-
-#ifdef CONFIG_LCD
- /* board init may have inited fb_base */
- if (!gd->fb_base) {
-# ifndef PAGE_SIZE
-# define PAGE_SIZE 4096
-# endif
- /*
- * reserve memory for LCD display (always full pages)
- */
- /* bss_end is defined in the board-specific linker script */
- addr = (_bss_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
- lcd_setmem (addr);
- gd->fb_base = addr;
- }
-#endif /* CONFIG_LCD */
-
-#if defined(CONFIG_CMD_NAND)
- puts ("NAND: ");
- nand_init(); /* go init the NAND */
-#endif
-
-#if defined(CONFIG_CMD_ONENAND)
- onenand_init();
-#endif
-
-#ifdef CONFIG_HAS_DATAFLASH
- AT91F_DataflashInit();
- dataflash_print_info();
-#endif
-
-#ifdef CONFIG_GENERIC_MMC
-/*
- * MMC initialization is called before relocating env.
- * Thus It is required that operations like pin multiplexer
- * be put in board_init.
- */
- puts ("MMC: ");
- mmc_initialize (gd->bd);
-#endif
-
- /* initialize environment */
- env_relocate ();
-
-#ifdef CONFIG_VFD
- /* must do this after the framebuffer is allocated */
- drv_vfd_init();
-#endif /* CONFIG_VFD */
-
-#ifdef CONFIG_SERIAL_MULTI
- serial_initialize();
-#endif
-
- /* IP Address */
- gd->bd->bi_ip_addr = getenv_IPaddr ("ipaddr");