Devkit8000: Switch over to enable_gpmc_cs_config

[oweals/u-boot.git] / README

diff --git a/README b/README
index 07f1d11e5feb2565df5422f3ccf940f1174a747d..79167777973ba665e75e44237a11ebc66e20ae10 100644 (file)
--- a/README
+++ b/README
@@ -564,7 +564,7 @@ The following options need to be configured:
 
                CONFIG_CFB_CONSOLE
                Enables console device for a color framebuffer. Needs following
 
                CONFIG_CFB_CONSOLE
                Enables console device for a color framebuffer. Needs following

-               defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
+               defines (cf. smiLynxEM, i8042)

                        VIDEO_FB_LITTLE_ENDIAN  graphic memory organisation
                                                (default big endian)
                        VIDEO_HW_RECTFILL       graphic chip supports
                        VIDEO_FB_LITTLE_ENDIAN  graphic memory organisation
                                                (default big endian)
                        VIDEO_HW_RECTFILL       graphic chip supports


@@ -638,6 +638,32 @@ The following options need to be configured:
                'Sane' compilers will generate smaller code if
                CONFIG_PRE_CON_BUF_SZ is a power of 2
 
                'Sane' compilers will generate smaller code if
                CONFIG_PRE_CON_BUF_SZ is a power of 2
 

+- Pre-console putc():
+               Prior to the console being initialised, console output is
+               normally silently discarded. This can be annoying if a
+               panic() happens in this time.
+
+               If the CONFIG_PRE_CONSOLE_PUTC option is defined, then
+               U-Boot will call board_pre_console_putc() for each output
+               character in this case, This function should try to output
+               the character if possible, perhaps on all available UARTs
+               (it will need to do this directly, since the console code
+               is not functional yet). Note that if the panic happens
+               early enough, then it is possible that board_init_f()
+               (or even arch_cpu_init() on ARM) has not been called yet.
+               You should init all clocks, GPIOs, etc. that are needed
+               to get the character out. Baud rates will need to default
+               to something sensible.
+
+- Safe printf() functions
+               Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
+               the printf() functions. These are defined in
+               include/vsprintf.h and include snprintf(), vsnprintf() and
+               so on. Code size increase is approximately 300-500 bytes.
+               If this option is not given then these functions will
+               silently discard their buffer size argument - this means
+               you are not getting any overflow checking in this case.
+

 - Boot Delay:  CONFIG_BOOTDELAY - in seconds
                Delay before automatically booting the default image;
                set to -1 to disable autoboot.
 - Boot Delay:  CONFIG_BOOTDELAY - in seconds
                Delay before automatically booting the default image;
                set to -1 to disable autoboot.


@@ -1072,6 +1098,16 @@ The following options need to be configured:
                        CONFIG_SH_ETHER_CACHE_WRITEBACK
                        If this option is set, the driver enables cache flush.
 
                        CONFIG_SH_ETHER_CACHE_WRITEBACK
                        If this option is set, the driver enables cache flush.
 

+- TPM Support:
+               CONFIG_GENERIC_LPC_TPM
+               Support for generic parallel port TPM devices. Only one device
+               per system is supported at this time.
+
+                       CONFIG_TPM_TIS_BASE_ADDRESS
+                       Base address where the generic TPM device is mapped
+                       to. Contemporary x86 systems usually map it at
+                       0xfed40000.
+

 - USB Support:
                At the moment only the UHCI host controller is
                supported (PIP405, MIP405, MPC5200); define
 - USB Support:
                At the moment only the UHCI host controller is
                supported (PIP405, MIP405, MPC5200); define


@@ -1158,6 +1194,14 @@ The following options need to be configured:
                        for your device
                        - CONFIG_USBD_PRODUCTID 0xFFFF
 
                        for your device
                        - CONFIG_USBD_PRODUCTID 0xFFFF
 

+- ULPI Layer Support:
+               The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
+               the generic ULPI layer. The generic layer accesses the ULPI PHY
+               via the platform viewport, so you need both the genric layer and
+               the viewport enabled. Currently only Chipidea/ARC based
+               viewport is supported.
+               To enable the ULPI layer support, define CONFIG_USB_ULPI and
+               CONFIG_USB_ULPI_VIEWPORT in your board configuration file.

 
 - MMC Support:
                The MMC controller on the Intel PXA is supported. To
 
 - MMC Support:
                The MMC controller on the Intel PXA is supported. To


@@ -3274,6 +3318,44 @@ Low Level (hardware related) configuration options:
                be used if available. These functions may be faster under some
                conditions but may increase the binary size.
 
                be used if available. These functions may be faster under some
                conditions but may increase the binary size.
 

+Freescale QE/FMAN Firmware Support:
+-----------------------------------
+
+The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
+loading of "firmware", which is encoded in the QE firmware binary format.
+This firmware often needs to be loaded during U-Boot booting, so macros
+are used to identify the storage device (NOR flash, SPI, etc) and the address
+within that device.
+
+- CONFIG_SYS_QE_FMAN_FW_ADDR
+       The address in the storage device where the firmware is located.  The
+       meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+       is also specified.
+
+- CONFIG_SYS_QE_FMAN_FW_LENGTH
+       The maximum possible size of the firmware.  The firmware binary format
+       has a field that specifies the actual size of the firmware, but it
+       might not be possible to read any part of the firmware unless some
+       local storage is allocated to hold the entire firmware first.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_NOR
+       Specifies that QE/FMAN firmware is located in NOR flash, mapped as
+       normal addressable memory via the LBC.  CONFIG_SYS_FMAN_FW_ADDR is the
+       virtual address in NOR flash.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_NAND
+       Specifies that QE/FMAN firmware is located in NAND flash.
+       CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_MMC
+       Specifies that QE/FMAN firmware is located on the primary SD/MMC
+       device.  CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
+       Specifies that QE/FMAN firmware is located on the primary SPI
+       device.  CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+
+

 Building the Software:
 ======================
 
 Building the Software:
 ======================