Fix incorrect use of getenv() before relocation

[oweals/u-boot.git] / README

diff --git a/README b/README
index ba4fdd44a3e7f60dac0096dc09a9f42c03e0222c..68dab2d1e3c4f1484f3d0dd4a81008b650b803a6 100644 (file)
--- a/README
+++ b/README
@@ -356,6 +356,13 @@ The following options need to be configured:
                Define this option if you want to enable the
                ICache only when Code runs from RAM.
 
                Define this option if you want to enable the
                ICache only when Code runs from RAM.
 

+- 85xx CPU Options:
+               CONFIG_SYS_FSL_TBCLK_DIV
+
+               Defines the core time base clock divider ratio compared to the
+               system clock.  On most PQ3 devices this is 8, on newer QorIQ
+               devices it can be 16 or 32.  The ratio varies from SoC to Soc.
+

 - Intel Monahans options:
                CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
 
 - Intel Monahans options:
                CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
 


@@ -468,6 +475,18 @@ The following options need to be configured:
                define this to a list of base addresses for each (supported)
                port. See e.g. include/configs/versatile.h
 
                define this to a list of base addresses for each (supported)
                port. See e.g. include/configs/versatile.h
 

+               CONFIG_PL011_SERIAL_RLCR
+
+               Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
+               have separate receive and transmit line control registers.  Set
+               this variable to initialize the extra register.
+
+               CONFIG_PL011_SERIAL_FLUSH_ON_INIT
+
+               On some platforms (e.g. U8500) U-Boot is loaded by a second stage
+               boot loader that has already initialized the UART.  Define this
+               variable to flush the UART at init time.
+

 
 - Console Interface:
                Depending on board, define exactly one serial port
 
 - Console Interface:
                Depending on board, define exactly one serial port


@@ -646,6 +665,7 @@ The following options need to be configured:
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support
                CONFIG_CMD_GO           * the 'go' command (exec code)
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support
                CONFIG_CMD_GO           * the 'go' command (exec code)

+               CONFIG_CMD_GREPENV      * search environment

                CONFIG_CMD_HWFLOW       * RTS/CTS hw flow control
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support
                CONFIG_CMD_HWFLOW       * RTS/CTS hw flow control
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support


@@ -1095,13 +1115,10 @@ The following options need to be configured:
                        CONFIG_VIDEO_LOGO
                        CONFIG_VIDEO_BMP_LOGO
 
                        CONFIG_VIDEO_LOGO
                        CONFIG_VIDEO_BMP_LOGO
 

-               The DIU driver will look for the 'monitor' environment variable,
-               and if defined, enable the DIU as a console during boot.  This
-               variable should be set to one of these values:
-
-                       '0'     Output video to the DVI connector
-                       '1'     Output video to the LVDS connector
-                       '2'     Output video to the Dual-Link LVDS connector
+               The DIU driver will look for the 'video-mode' environment
+               variable, and if defined, enable the DIU as a console during
+               boot.  See the documentation file README.video for a
+               description of this variable.

 
 - Keyboard Support:
                CONFIG_KEYBOARD
 
 - Keyboard Support:
                CONFIG_KEYBOARD


@@ -1305,7 +1322,6 @@ The following options need to be configured:
                driver in use must provide a function: mcast() to join/leave a
                multicast group.
 
                driver in use must provide a function: mcast() to join/leave a
                multicast group.
 

-               CONFIG_BOOTP_RANDOM_DELAY

 - BOOTP Recovery Mode:
                CONFIG_BOOTP_RANDOM_DELAY
 
 - BOOTP Recovery Mode:
                CONFIG_BOOTP_RANDOM_DELAY
 


@@ -2362,7 +2378,10 @@ Configuration Settings:
                used) must be put below this limit, unless "bootm_low"
                enviroment variable is defined and non-zero. In such case
                all data for the Linux kernel must be between "bootm_low"
                used) must be put below this limit, unless "bootm_low"
                enviroment variable is defined and non-zero. In such case
                all data for the Linux kernel must be between "bootm_low"

-               and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.
+               and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.  The environment
+               variable "bootm_mapsize" will override the value of
+               CONFIG_SYS_BOOTMAPSZ.  If CONFIG_SYS_BOOTMAPSZ is undefined,
+               then the value in "bootm_size" will be used instead.

 
 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
                Enable initrd_high functionality.  If defined then the
 
 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
                Enable initrd_high functionality.  If defined then the


@@ -2750,6 +2769,14 @@ Low Level (hardware related) configuration options:
                source code. It is used to make hardware dependant
                initializations.
 
                source code. It is used to make hardware dependant
                initializations.
 

+- CONFIG_IDE_AHB:
+               Most IDE controllers were designed to be connected with PCI
+               interface. Only few of them were designed for AHB interface.
+               When software is doing ATA command and data transfer to
+               IDE devices through IDE-AHB controller, some additional
+               registers accessing to these kind of IDE-AHB controller
+               is requierd.
+

 - CONFIG_SYS_IMMR:     Physical address of the Internal Memory.
                DO NOT CHANGE unless you know exactly what you're
                doing! (11-4) [MPC8xx/82xx systems only]
 - CONFIG_SYS_IMMR:     Physical address of the Internal Memory.
                DO NOT CHANGE unless you know exactly what you're
                doing! (11-4) [MPC8xx/82xx systems only]


@@ -3204,7 +3231,16 @@ List of environment variables (most likely not complete):
                  for use by the bootm command. See also "bootm_size"
                  environment variable. Address defined by "bootm_low" is
                  also the base of the initial memory mapping for the Linux
                  for use by the bootm command. See also "bootm_size"
                  environment variable. Address defined by "bootm_low" is
                  also the base of the initial memory mapping for the Linux

-                 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ.
+                 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
+                 bootm_mapsize.
+
+  bootm_mapsize        - Size of the initial memory mapping for the Linux kernel.
+                 This variable is given as a hexadecimal number and it
+                 defines the size of the memory region starting at base
+                 address bootm_low that is accessible by the Linux kernel
+                 during early boot.  If unset, CONFIG_SYS_BOOTMAPSZ is used
+                 as the default value if it is defined, and bootm_size is
+                 used otherwise.

 
   bootm_size   - Memory range available for image processing in the bootm
                  command can be restricted. This variable is given as
 
   bootm_size   - Memory range available for image processing in the bootm
                  command can be restricted. This variable is given as