menu "x86 architecture" depends on X86 config SYS_ARCH default "x86" choice prompt "Mainboard vendor" default VENDOR_EMULATION config VENDOR_COREBOOT bool "coreboot" config VENDOR_EFI bool "efi" config VENDOR_EMULATION bool "emulation" config VENDOR_GOOGLE bool "Google" config VENDOR_INTEL bool "Intel" endchoice # board-specific options below source "board/coreboot/Kconfig" source "board/efi/Kconfig" source "board/emulation/Kconfig" source "board/google/Kconfig" source "board/intel/Kconfig" # platform-specific options below source "arch/x86/cpu/baytrail/Kconfig" source "arch/x86/cpu/coreboot/Kconfig" source "arch/x86/cpu/ivybridge/Kconfig" source "arch/x86/cpu/qemu/Kconfig" source "arch/x86/cpu/quark/Kconfig" source "arch/x86/cpu/queensbay/Kconfig" # architecture-specific options below config SYS_MALLOC_F_LEN default 0x800 config RAMBASE hex default 0x100000 config XIP_ROM_SIZE hex depends on X86_RESET_VECTOR default ROM_SIZE config CPU_ADDR_BITS int default 36 config HPET_ADDRESS hex default 0xfed00000 if !HPET_ADDRESS_OVERRIDE config SMM_TSEG bool default n config SMM_TSEG_SIZE hex config X86_RESET_VECTOR bool default n config RESET_SEG_START hex depends on X86_RESET_VECTOR default 0xffff0000 config RESET_SEG_SIZE hex depends on X86_RESET_VECTOR default 0x10000 config RESET_VEC_LOC hex depends on X86_RESET_VECTOR default 0xfffffff0 config SYS_X86_START16 hex depends on X86_RESET_VECTOR default 0xfffff800 config BOARD_ROMSIZE_KB_512 bool config BOARD_ROMSIZE_KB_1024 bool config BOARD_ROMSIZE_KB_2048 bool config BOARD_ROMSIZE_KB_4096 bool config BOARD_ROMSIZE_KB_8192 bool config BOARD_ROMSIZE_KB_16384 bool choice prompt "ROM chip size" depends on X86_RESET_VECTOR default UBOOT_ROMSIZE_KB_512 if BOARD_ROMSIZE_KB_512 default UBOOT_ROMSIZE_KB_1024 if BOARD_ROMSIZE_KB_1024 default UBOOT_ROMSIZE_KB_2048 if BOARD_ROMSIZE_KB_2048 default UBOOT_ROMSIZE_KB_4096 if BOARD_ROMSIZE_KB_4096 default UBOOT_ROMSIZE_KB_8192 if BOARD_ROMSIZE_KB_8192 default UBOOT_ROMSIZE_KB_16384 if BOARD_ROMSIZE_KB_16384 help Select the size of the ROM chip you intend to flash U-Boot on. The build system will take care of creating a u-boot.rom file of the matching size. config UBOOT_ROMSIZE_KB_512 bool "512 KB" help Choose this option if you have a 512 KB ROM chip. config UBOOT_ROMSIZE_KB_1024 bool "1024 KB (1 MB)" help Choose this option if you have a 1024 KB (1 MB) ROM chip. config UBOOT_ROMSIZE_KB_2048 bool "2048 KB (2 MB)" help Choose this option if you have a 2048 KB (2 MB) ROM chip. config UBOOT_ROMSIZE_KB_4096 bool "4096 KB (4 MB)" help Choose this option if you have a 4096 KB (4 MB) ROM chip. config UBOOT_ROMSIZE_KB_8192 bool "8192 KB (8 MB)" help Choose this option if you have a 8192 KB (8 MB) ROM chip. config UBOOT_ROMSIZE_KB_16384 bool "16384 KB (16 MB)" help Choose this option if you have a 16384 KB (16 MB) ROM chip. endchoice # Map the config names to an integer (KB). config UBOOT_ROMSIZE_KB int default 512 if UBOOT_ROMSIZE_KB_512 default 1024 if UBOOT_ROMSIZE_KB_1024 default 2048 if UBOOT_ROMSIZE_KB_2048 default 4096 if UBOOT_ROMSIZE_KB_4096 default 8192 if UBOOT_ROMSIZE_KB_8192 default 16384 if UBOOT_ROMSIZE_KB_16384 # Map the config names to a hex value (bytes). config ROM_SIZE hex default 0x80000 if UBOOT_ROMSIZE_KB_512 default 0x100000 if UBOOT_ROMSIZE_KB_1024 default 0x200000 if UBOOT_ROMSIZE_KB_2048 default 0x400000 if UBOOT_ROMSIZE_KB_4096 default 0x800000 if UBOOT_ROMSIZE_KB_8192 default 0xc00000 if UBOOT_ROMSIZE_KB_12288 default 0x1000000 if UBOOT_ROMSIZE_KB_16384 config HAVE_INTEL_ME bool "Platform requires Intel Management Engine" help Newer higher-end devices have an Intel Management Engine (ME) which is a very large binary blob (typically 1.5MB) which is required for the platform to work. This enforces a particular SPI flash format. You will need to supply the me.bin file in your board directory. config X86_RAMTEST bool "Perform a simple RAM test after SDRAM initialisation" help If there is something wrong with SDRAM then the platform will often crash within U-Boot or the kernel. This option enables a very simple RAM test that quickly checks whether the SDRAM seems to work correctly. It is not exhaustive but can save time by detecting obvious failures. config HAVE_FSP bool "Add an Firmware Support Package binary" depends on !EFI help Select this option to add an Firmware Support Package binary to the resulting U-Boot image. It is a binary blob which U-Boot uses to set up SDRAM and other chipset specific initialization. Note: Without this binary U-Boot will not be able to set up its SDRAM so will not boot. config FSP_FILE string "Firmware Support Package binary filename" depends on HAVE_FSP default "fsp.bin" help The filename of the file to use as Firmware Support Package binary in the board directory. config FSP_ADDR hex "Firmware Support Package binary location" depends on HAVE_FSP default 0xfffc0000 help FSP is not Position Independent Code (PIC) and the whole FSP has to be rebased if it is placed at a location which is different from the perferred base address specified during the FSP build. Use Intel's Binary Configuration Tool (BCT) to do the rebase. The default base address of 0xfffc0000 indicates that the binary must be located at offset 0xc0000 from the beginning of a 1MB flash device. config FSP_TEMP_RAM_ADDR hex depends on HAVE_FSP default 0x2000000 help Stack top address which is used in fsp_init() after DRAM is ready and CAR is disabled. config FSP_SYS_MALLOC_F_LEN hex depends on HAVE_FSP default 0x100000 help Additional size of malloc() pool before relocation. config ENABLE_MRC_CACHE bool "Enable MRC cache" depends on !EFI && !SYS_COREBOOT help Enable this feature to cause MRC data to be cached in NV storage to be used for speeding up boot time on future reboots and/or power cycles. config SMP bool "Enable Symmetric Multiprocessing" default n help Enable use of more than one CPU in U-Boot and the Operating System when loaded. Each CPU will be started up and information can be obtained using the 'cpu' command. If this option is disabled, then only one CPU will be enabled regardless of the number of CPUs available. config MAX_CPUS int "Maximum number of CPUs permitted" depends on SMP default 4 help When using multi-CPU chips it is possible for U-Boot to start up more than one CPU. The stack memory used by all of these CPUs is pre-allocated so at present U-Boot wants to know the maximum number of CPUs that may be present. Set this to at least as high as the number of CPUs in your system (it uses about 4KB of RAM for each CPU). config AP_STACK_SIZE hex depends on SMP default 0x1000 help Each additional CPU started by U-Boot requires its own stack. This option sets the stack size used by each CPU and directly affects the memory used by this initialisation process. Typically 4KB is enough space. config TSC_CALIBRATION_BYPASS bool "Bypass Time-Stamp Counter (TSC) calibration" default n help By default U-Boot automatically calibrates Time-Stamp Counter (TSC) running frequency via Model-Specific Register (MSR) and Programmable Interval Timer (PIT). If the calibration does not work on your board, select this option and provide a hardcoded TSC running frequency with CONFIG_TSC_FREQ_IN_MHZ below. Normally this option should be turned on in a simulation environment like qemu. config TSC_FREQ_IN_MHZ int "Time-Stamp Counter (TSC) running frequency in MHz" depends on TSC_CALIBRATION_BYPASS default 1000 help The running frequency in MHz of Time-Stamp Counter (TSC). config HAVE_VGA_BIOS bool "Add a VGA BIOS image" help Select this option if you have a VGA BIOS image that you would like to add to your ROM. config VGA_BIOS_FILE string "VGA BIOS image filename" depends on HAVE_VGA_BIOS default "vga.bin" help The filename of the VGA BIOS image in the board directory. config VGA_BIOS_ADDR hex "VGA BIOS image location" depends on HAVE_VGA_BIOS default 0xfff90000 help The location of VGA BIOS image in the SPI flash. For example, base address of 0xfff90000 indicates that the image will be put at offset 0x90000 from the beginning of a 1MB flash device. menu "System tables" depends on !EFI && !SYS_COREBOOT config GENERATE_PIRQ_TABLE bool "Generate a PIRQ table" default n help Generate a PIRQ routing table for this board. The PIRQ routing table is generated by U-Boot in the system memory from 0xf0000 to 0xfffff at every 16-byte boundary with a PCI IRQ routing signature ("$PIR"). It specifies the interrupt router information as well how all the PCI devices' interrupt pins are wired to PIRQs. config GENERATE_SFI_TABLE bool "Generate a SFI (Simple Firmware Interface) table" help The Simple Firmware Interface (SFI) provides a lightweight method for platform firmware to pass information to the operating system via static tables in memory. Kernel SFI support is required to boot on SFI-only platforms. If you have ACPI tables then these are used instead. U-Boot writes this table in write_sfi_table() just before booting the OS. For more information, see http://simplefirmware.org config GENERATE_MP_TABLE bool "Generate an MP (Multi-Processor) table" default n help Generate an MP (Multi-Processor) table for this board. The MP table provides a way for the operating system to support for symmetric multiprocessing as well as symmetric I/O interrupt handling with the local APIC and I/O APIC. config GENERATE_ACPI_TABLE bool "Generate an ACPI (Advanced Configuration and Power Interface) table" default n help The Advanced Configuration and Power Interface (ACPI) specification provides an open standard for device configuration and management by the operating system. It defines platform-independent interfaces for configuration and power management monitoring. config GENERATE_SMBIOS_TABLE bool "Generate an SMBIOS (System Management BIOS) table" default y help The System Management BIOS (SMBIOS) specification addresses how motherboard and system vendors present management information about their products in a standard format by extending the BIOS interface on Intel architecture systems. Check http://www.dmtf.org/standards/smbios for details. endmenu config MAX_PIRQ_LINKS int default 8 help This variable specifies the number of PIRQ interrupt links which are routable. On most older chipsets, this is 4, PIRQA through PIRQD. Some newer chipsets offer more than four links, commonly up to PIRQH. config IRQ_SLOT_COUNT int default 128 help U-Boot can support up to 254 IRQ slot info in the PIRQ routing table which in turns forms a table of exact 4KiB. The default value 128 should be enough for most boards. If this does not fit your board, change it according to your needs. config PCIE_ECAM_BASE hex default 0xe0000000 help This is the memory-mapped address of PCI configuration space, which is only available through the Enhanced Configuration Access Mechanism (ECAM) with PCI Express. It can be set up almost anywhere. Before it is set up, it is possible to access PCI configuration space through I/O access, but memory access is more convenient. Using this, PCI can be scanned and configured. This should be set to a region that does not conflict with memory assigned to PCI devices - i.e. the memory and prefetch regions, as passed to pci_set_region(). config PCIE_ECAM_SIZE hex default 0x10000000 help This is the size of memory-mapped address of PCI configuration space, which is only available through the Enhanced Configuration Access Mechanism (ECAM) with PCI Express. Each bus consumes 1 MiB memory, so a default 0x10000000 size covers all of the 256 buses which is the maximum number of PCI buses as defined by the PCI specification. config I8259_PIC bool default y help Intel 8259 ISA compatible chipset incorporates two 8259 (master and slave) interrupt controllers. Include this to have U-Boot set up the interrupt correctly. config I8254_TIMER bool default y help Intel 8254 timer contains three counters which have fixed uses. Include this to have U-Boot set up the timer correctly. source "arch/x86/lib/efi/Kconfig" endmenu