if ARCH_ZYNQMP config SPL_FS_FAT default y config SPL_LIBCOMMON_SUPPORT default y config SPL_LIBDISK_SUPPORT default y config SPL_LIBGENERIC_SUPPORT default y config SPL_MMC_SUPPORT default y if MMC_SDHCI_ZYNQ config SPL_SERIAL_SUPPORT default y config SPL_SPI_FLASH_SUPPORT default y if ZYNQ_QSPI config SPL_SPI_SUPPORT default y if ZYNQ_QSPI config SYS_BOARD default "zynqmp" config SYS_VENDOR string "Vendor name" default "xilinx" config SYS_SOC default "zynqmp" config SYS_CONFIG_NAME string "Board configuration name" default "xilinx_zynqmp" help This option contains information about board configuration name. Based on this option include/configs/.h header will be used for board configuration. config SYS_MEM_RSVD_FOR_MMU bool "Reserve memory for MMU Table" help If defined this option is used to setup different space for MMU table than the one which will be allocated during relocation. config BOOT_INIT_FILE string "boot.bin init register filename" depends on SPL default "" help Add register writes to boot.bin format (max 256 pairs). Expect a table of register-value pairs, e.g. "0x12345678 0x4321" config PMUFW_INIT_FILE string "PMU firmware" depends on SPL default "" help Include external PMUFW (Platform Management Unit FirmWare) to a Xilinx bootable image (boot.bin). config ZYNQMP_SPL_PM_CFG_OBJ_FILE string "PMU firmware configuration object to load at runtime by SPL" depends on SPL help Path to a binary PMU firmware configuration object to be linked into U-Boot SPL and loaded at runtime into the PMU firmware. The ZynqMP Power Management Unit (PMU) needs a configuration object for most SoC peripherals to work. To have it loaded by U-Boot SPL set here the file name (absolute path or relative to the top source tree) of your configuration, which must be a binary blob. It will be linked in the SPL binary and loaded into the PMU firmware by U-Boot SPL during board initialization. Leave this option empty if your PMU firmware has a hard-coded configuration object or you are loading it by any other means. config ZYNQMP_USB bool "Configure ZynqMP USB" config ZYNQMP_NO_DDR bool "Disable DDR MMU mapping" help This option configures MMU with no DDR to avoid speculative access to DDR memory where DDR is not present. config SYS_MALLOC_F_LEN default 0x600 config DEFINE_TCM_OCM_MMAP bool "Define TCM and OCM memory in MMU Table" default y if MP help This option if enabled defines the TCM and OCM memory and its memory attributes in MMU table entry. config ZYNQMP_PSU_INIT_ENABLED bool "Include psu_init" help Include psu_init to full u-boot. SPL include psu_init by default. config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED bool "Overwrite SPL bootmode" depends on SPL help Overwrite bootmode selected via boot mode pins to tell SPL what should be the next boot device. config ZYNQ_SDHCI_MAX_FREQ default 200000000 config SPL_ZYNQMP_ALT_BOOTMODE hex default 0x0 if JTAG_MODE default 0x1 if QSPI_MODE_24BIT default 0x2 if QSPI_MODE_32BIT default 0x3 if SD_MODE default 0x4 if NAND_MODE default 0x5 if SD_MODE1 default 0x6 if EMMC_MODE default 0x7 if USB_MODE default 0xa if SW_USBHOST_MODE default 0xb if SW_SATA_MODE default 0xe if SD1_LSHFT_MODE choice prompt "Boot mode" depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED default JTAG_MODE config JTAG_MODE bool "JTAG_MODE" config QSPI_MODE_24BIT bool "QSPI_MODE_24BIT" config QSPI_MODE_32BIT bool "QSPI_MODE_32BIT" config SD_MODE bool "SD_MODE" config SD_MODE1 bool "SD_MODE1" config NAND_MODE bool "NAND_MODE" config EMMC_MODE bool "EMMC_MODE" config USB_MODE bool "USB" config SW_USBHOST_MODE bool "SW USBHOST_MODE" config SW_SATA_MODE bool "SW SATA_MODE" config SD1_LSHFT_MODE bool "SD1_LSHFT_MODE" endchoice endif