target/linux/ramips/dts/mt7620a_zbtlink_zbt-ape522ii.dts

   1 /dts-v1/;
   2
   3 #include "mt7620a.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "zbtlink,zbt-ape522ii", "ralink,mt7620a-soc";
  10         model = "Zbtlink ZBT-APE522II";
  11
  12         chosen {
  13                 bootargs = "console=ttyS0,115200";
  14         };
  15
  16         leds {
  17                 compatible = "gpio-leds";
  18
  19                 sys1 {
  20                         label = "zbt-ape522ii:green:sys1";
  21                         gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
  22                 };
  23
  24                 sys2 {
  25                         label = "zbt-ape522ii:green:sys2";
  26                         gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
  27                 };
  28
  29                 sys3 {
  30                         label = "zbt-ape522ii:green:sys3";
  31                         gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  32                 };
  33
  34                 sys4 {
  35                         label = "zbt-ape522ii:green:sys4";
  36                         gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
  37                 };
  38
  39                 wlan2g4 {
  40                         label = "zbt-ape522ii:green:wlan2g4";
  41                         gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
  42                 };
  43         };
  44
  45         keys {
  46                 compatible = "gpio-keys";
  47
  48                 reset {
  49                         label = "reset";
  50                         gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
  51                         linux,code = <KEY_RESTART>;
  52                 };
  53         };
  54 };
  55
  56 &gpio0 {
  57         status = "okay";
  58 };
  59
  60 &gpio1 {
  61         status = "okay";
  62 };
  63
  64 &gpio2 {
  65         status = "okay";
  66 };
  67
  68 &gpio3 {
  69         status = "okay";
  70 };
  71
  72 &spi0 {
  73         status = "okay";
  74
  75         m25p80@0 {
  76                 compatible = "jedec,spi-nor";
  77                 reg = <0>;
  78                 spi-max-frequency = <10000000>;
  79
  80                 partitions {
  81                         compatible = "fixed-partitions";
  82                         #address-cells = <1>;
  83                         #size-cells = <1>;
  84
  85                         partition@0 {
  86                                 label = "u-boot";
  87                                 reg = <0x0 0x30000>;
  88                         };
  89
  90                         partition@30000 {
  91                                 label = "u-boot-env";
  92                                 reg = <0x30000 0x10000>;
  93                                 read-only;
  94                         };
  95
  96                         factory: partition@40000 {
  97                                 label = "factory";
  98                                 reg = <0x40000 0x10000>;
  99                                 read-only;
 100                         };
 101
 102                         partition@50000 {
 103                                 compatible = "denx,uimage";
 104                                 label = "firmware";
 105                                 reg = <0x50000 0xf80000>;
 106                         };
 107                 };
 108         };
 109 };
 110
 111 &ethernet {
 112         pinctrl-names = "default";
 113         pinctrl-0 = <&ephy_pins>;
 114         mtd-mac-address = <&factory 0x4>;
 115         mediatek,portmap = "wllll";
 116 };
 117
 118 &wmac {
 119         ralink,mtd-eeprom = <&factory 0>;
 120         pinctrl-names = "default";
 121         pinctrl-0 = <&pa_pins>;
 122 };
 123
 124 &pcie {
 125         status = "okay";
 126 };
 127
 128 &pcie0 {
 129         mt76@0,0 {
 130                 reg = <0x0000 0 0 0 0>;
 131                 mediatek,mtd-eeprom = <&factory 0x8000>;
 132                 ieee80211-freq-limit = <5000000 6000000>;
 133         };
 134 };
 135
 136 &state_default {
 137         gpio {
 138                 groups = "wled", "i2c", "uartf", "wdt";
 139                 function = "gpio";
 140         };
 141 };