target/linux/ramips/dts/WZR-AGL300NH.dts

   1 /dts-v1/;
   2
   3 #include "rt2880.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         #address-cells = <1>;
  10         #size-cells = <1>;
  11         compatible = "buffalo,wzr-agl300nh", "ralink,rt2880-soc";
  12         model = "Buffalo WZR-AGL300NH";
  13
  14         aliases {
  15                 led-boot = &led_router;
  16                 led-failsafe = &led_router;
  17                 led-running = &led_router;
  18                 led-upgrade = &led_router;
  19         };
  20
  21         cfi@1f000000 {
  22                 compatible = "cfi-flash";
  23                 reg = <0x1f000000 0x800000>;
  24                 bank-width = <2>;
  25                 device-width = <2>;
  26
  27                 partitions {
  28                         compatible = "fixed-partitions";
  29                         #address-cells = <1>;
  30                         #size-cells = <1>;
  31
  32                         partition@0 {
  33                                 label = "uboot";
  34                                 reg = <0x0 0x30000>;
  35                                 read-only;
  36                         };
  37
  38                         partition@30000 {
  39                                 label = "uboot-env";
  40                                 reg = <0x30000 0x10000>;
  41                                 read-only;
  42                         };
  43
  44                         factory: partition@40000 {
  45                                 label = "factory";
  46                                 reg = <0x40000 0x10000>;
  47                                 read-only;
  48                         };
  49
  50                         partition@50000 {
  51                                 label = "firmware";
  52                                 reg = <0x50000 0x3b0000>;
  53                         };
  54                 };
  55         };
  56
  57         rtl8366s {
  58                 compatible = "realtek,rtl8366s";
  59                 gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
  60                 gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
  61         };
  62
  63         gpio-keys-polled {
  64                 compatible = "gpio-keys-polled";
  65                 poll-interval = <100>;
  66
  67                 wps {
  68                         label = "wps";
  69                         gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
  70                         linux,code = <KEY_WPS_BUTTON>;
  71                 };
  72
  73                 router {
  74                         label = "router_switch";
  75                         gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
  76                         linux,code = <BTN_0>;
  77                 };
  78
  79                 reset {
  80                         label = "reset";
  81                         gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  82                         linux,code = <KEY_RESTART>;
  83                 };
  84         };
  85
  86         gpio-leds {
  87                 compatible = "gpio-leds";
  88
  89                 led_router: router {
  90                         label = "wzr-agl300nh:green:router";
  91                         gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
  92                 };
  93
  94                 diag {
  95                         label = "wzr-agl300nh:red:diag";
  96                         gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
  97                 };
  98
  99                 security_g {
 100                         label = "wzr-agl300nh:orange:security_g";
 101                         gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
 102                 };
 103
 104                 security_n {
 105                         label = "wzr-agl300nh:orange:security_n";
 106                         gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
 107                 };
 108         };
 109 };
 110
 111 &gpio0 {
 112         status = "okay";
 113 };
 114
 115 &pinctrl {
 116         state_default: pinctrl0 {
 117                 gpio {
 118                         ralink,group = "i2c", "uartlite", "mdio";
 119                         ralink,function = "gpio";
 120                 };
 121         };
 122 };
 123
 124 &ethernet {
 125         status = "okay";
 126         mtd-mac-address = <&factory 0x4>;
 127
 128         port@0 {
 129                 mediatek,fixed-link = <1000 1 1 1>;
 130         };
 131
 132         mdio-bus {
 133                 status = "okay";
 134
 135                 phy0: ethernet-phy@0 {
 136                         phy-mode = "mii";
 137                         reg = <0>;
 138                 };
 139         };
 140 };
 141
 142 &pci {
 143         status = "okay";
 144 };
 145
 146 &wmac {
 147         ralink,mtd-eeprom = <&factory 0>;
 148 };