target/linux/ramips/dts/WZR-AGL300NH.dts

   1 /dts-v1/;
   2
   3 #include "rt2880.dtsi"
   4
   5 / {
   6         #address-cells = <1>;
   7         #size-cells = <1>;
   8         compatible = "WZR-AGL300NH", "ralink,rt2880-soc";
   9         model = "Buffalo WZR-AGL300NH";
  10
  11         pci@440000 {
  12                 compatible = "ralink,rt288x-pci";
  13                 reg = <0x00440000 0x20000>;
  14                 #address-cells = <1>;
  15                 #size-cells = <1>;
  16                 status = "ok";
  17         };
  18
  19         cfi@1f000000 {
  20                 compatible = "cfi-flash";
  21                 reg = <0x1f000000 0x800000>;
  22                 bank-width = <2>;
  23                 device-width = <2>;
  24                 #address-cells = <1>;
  25                 #size-cells = <1>;
  26
  27                 partition@0 {
  28                         label = "uboot";
  29                         reg = <0x0 0x30000>;
  30                         read-only;
  31                 };
  32
  33                 partition@30000 {
  34                         label = "uboot-env";
  35                         reg = <0x30000 0x10000>;
  36                         read-only;
  37                 };
  38
  39                 factory: partition@40000 {
  40                         label = "factory";
  41                         reg = <0x40000 0x10000>;
  42                         read-only;
  43                 };
  44
  45                 partition@50000 {
  46                         label = "firmware";
  47                         reg = <0x50000 0x3b0000>;
  48                 };
  49         };
  50
  51         rtl8366s {
  52                 compatible = "realtek,rtl8366s";
  53                 gpio-sda = <&gpio0 1 0>;
  54                 gpio-sck = <&gpio0 2 0>;
  55         };
  56
  57         gpio-keys-polled {
  58                 compatible = "gpio-keys-polled";
  59                 #address-cells = <1>;
  60                 #size-cells = <0>;
  61                 poll-interval = <100>;
  62
  63                 wps {
  64                         label = "wps";
  65                         gpios = <&gpio0 0 1>;
  66                         linux,code = <0x211>;
  67                 };
  68
  69                 router {
  70                         label = "router_switch";
  71                         gpios = <&gpio0 7 0>;
  72                         linux,code = <0x100>;
  73                 };
  74
  75                 reset {
  76                         label = "reset";
  77                         gpios = <&gpio0 9 1>;
  78                         linux,code = <0x198>;
  79                 };
  80         };
  81
  82         gpio-leds {
  83                 compatible = "gpio-leds";
  84
  85                 router {
  86                         label = "wzr-agl300nh:green:router";
  87                         gpios = <&gpio0 8 1>;
  88                 };
  89
  90                 diag {
  91                         label = "wzr-agl300nh:red:diag";
  92                         gpios = <&gpio0 12 1>;
  93                 };
  94
  95                 security_g {
  96                         label = "wzr-agl300nh:orange:security_g";
  97                         gpios = <&gpio0 11 1>;
  98                 };
  99
 100                 security_n {
 101                         label = "wzr-agl300nh:orange:security_n";
 102                         gpios = <&gpio0 13 1>;
 103                 };
 104         };
 105 };
 106
 107 &gpio0 {
 108         status = "okay";
 109 };
 110
 111 &pinctrl {
 112         state_default: pinctrl0 {
 113                 gpio {
 114                         ralink,group = "i2c", "uartlite", "mdio";
 115                         ralink,function = "gpio";
 116                 };
 117         };
 118 };
 119
 120 &ethernet {
 121         status = "okay";
 122         mtd-mac-address = <&factory 0x4>;
 123
 124         port@0 {
 125                 mediatek,fixed-link = <1000 1 1 1>;
 126         };
 127
 128         mdio-bus {
 129                 status = "okay";
 130
 131                 phy0: ethernet-phy@0 {
 132                         phy-mode = "mii";
 133                         reg = <0>;
 134                 };
 135         };
 136 };
 137
 138 &wmac {
 139         ralink,mtd-eeprom = <&factory 0>;
 140 };