target/linux/ramips/dts/F7C027.dts

   1 /dts-v1/;
   2
   3 #include "rt5350.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "belkin,f7c027", "ralink,rt5350-soc";
  10         model = "Belkin F7C027";
  11
  12         aliases {
  13                 led-status = &led_status_orange;
  14         };
  15
  16         gpio-leds {
  17                 compatible = "gpio-leds";
  18
  19                 status {
  20                         label = "f7c027:blue:status";
  21                         gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
  22                 };
  23
  24                 power {
  25                         label = "f7c027:blue:power";
  26                         gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  27                 };
  28
  29                 led_status_orange: orange {
  30                         label = "f7c027:orange:status";
  31                         gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
  32                 };
  33
  34                 relay {
  35                         label = "f7c027:device:relay";
  36                         gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
  37                 };
  38         };
  39
  40         gpio-keys-polled {
  41                 compatible = "gpio-keys-polled";
  42                 #address-cells = <1>;
  43                 #size-cells = <0>;
  44                 poll-interval = <20>;
  45
  46                 top {
  47                         label = "restore";
  48                         gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
  49                         linux,code = <KEY_RESTART>;
  50                 };
  51
  52                 power {
  53                         label = "power";
  54                         gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
  55                         linux,code = <KEY_RFKILL>;
  56                 };
  57
  58                 sensor {
  59                         label = "sensor";
  60                         gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
  61                         linux,code = <BTN_0>;
  62                 };
  63         };
  64 };
  65
  66 &spi0 {
  67         status = "okay";
  68
  69         m25p80@0 {
  70                 #address-cells = <1>;
  71                 #size-cells = <1>;
  72                 compatible = "jedec,spi-nor";
  73                 reg = <0>;
  74                 spi-max-frequency = <10000000>;
  75
  76                 partition@0 {
  77                         label = "u-boot";
  78                         reg = <0x0 0x30000>;
  79                         read-only;
  80                 };
  81
  82                 partition@30000 {
  83                         label = "u-boot-env";
  84                         reg = <0x30000 0x10000>;
  85                         read-only;
  86                 };
  87
  88                 factory: partition@40000 {
  89                         label = "factory";
  90                         reg = <0x40000 0x10000>;
  91                         read-only;
  92                 };
  93
  94                 partition@50000 {
  95                         label = "firmware";
  96                         reg = <0x50000 0x770000>;
  97                 };
  98
  99                 partition@7c0000 {
 100                         label = "firmware2";
 101                         reg = <0x7c0000 0x770000>;
 102                 };
 103
 104                 partition@f30000 {
 105                         label = "belkin_settings";
 106                         reg = <0xf30000 0xa0000>;
 107                 };
 108
 109                 partition@fd0000 {
 110                         label = "unknown";
 111                         reg = <0xfd0000 0x10000>;
 112                 };
 113
 114                 partition@fe0000 {
 115                         label = "nvram";
 116                         reg = <0xfe0000 0x10000>;
 117                 };
 118
 119                 partition@ff0000 {
 120                         label = "user_factory";
 121                         reg = <0xff0000 0x10000>;
 122                 };
 123         };
 124 };
 125
 126 &wmac {
 127         ralink,mtd-eeprom = <&factory 0>;
 128 };
 129
 130 &pinctrl {
 131         state_default: pinctrl0 {
 132                 gpio {
 133                         ralink,group = "i2c", "jtag", "uartf";
 134                         ralink,function = "gpio";
 135                 };
 136         };
 137 };