target/linux/ramips/dts/F7C027.dts

   1 /dts-v1/;
   2
   3 #include "rt5350.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "belkin,f7c027", "ralink,rt5350-soc";
  10         model = "Belkin F7C027";
  11
  12         aliases {
  13                 led-status = &led_status_orange;
  14         };
  15
  16         gpio-leds {
  17                 compatible = "gpio-leds";
  18
  19                 status {
  20                         label = "f7c027:blue:status";
  21                         gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
  22                 };
  23
  24                 power {
  25                         label = "f7c027:blue:power";
  26                         gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  27                 };
  28
  29                 led_status_orange: orange {
  30                         label = "f7c027:orange:status";
  31                         gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
  32                 };
  33
  34                 relay {
  35                         label = "f7c027:device:relay";
  36                         gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
  37                 };
  38         };
  39
  40         gpio-keys-polled {
  41                 compatible = "gpio-keys-polled";
  42                 poll-interval = <20>;
  43
  44                 top {
  45                         label = "restore";
  46                         gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
  47                         linux,code = <KEY_RESTART>;
  48                 };
  49
  50                 power {
  51                         label = "power";
  52                         gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
  53                         linux,code = <KEY_RFKILL>;
  54                 };
  55
  56                 sensor {
  57                         label = "sensor";
  58                         gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
  59                         linux,code = <BTN_0>;
  60                 };
  61         };
  62 };
  63
  64 &spi0 {
  65         status = "okay";
  66
  67         m25p80@0 {
  68                 #address-cells = <1>;
  69                 #size-cells = <1>;
  70                 compatible = "jedec,spi-nor";
  71                 reg = <0>;
  72                 spi-max-frequency = <10000000>;
  73
  74                 partition@0 {
  75                         label = "u-boot";
  76                         reg = <0x0 0x30000>;
  77                         read-only;
  78                 };
  79
  80                 partition@30000 {
  81                         label = "u-boot-env";
  82                         reg = <0x30000 0x10000>;
  83                         read-only;
  84                 };
  85
  86                 factory: partition@40000 {
  87                         label = "factory";
  88                         reg = <0x40000 0x10000>;
  89                         read-only;
  90                 };
  91
  92                 partition@50000 {
  93                         label = "firmware";
  94                         reg = <0x50000 0x770000>;
  95                 };
  96
  97                 partition@7c0000 {
  98                         label = "firmware2";
  99                         reg = <0x7c0000 0x770000>;
 100                 };
 101
 102                 partition@f30000 {
 103                         label = "belkin_settings";
 104                         reg = <0xf30000 0xa0000>;
 105                 };
 106
 107                 partition@fd0000 {
 108                         label = "unknown";
 109                         reg = <0xfd0000 0x10000>;
 110                 };
 111
 112                 partition@fe0000 {
 113                         label = "nvram";
 114                         reg = <0xfe0000 0x10000>;
 115                 };
 116
 117                 partition@ff0000 {
 118                         label = "user_factory";
 119                         reg = <0xff0000 0x10000>;
 120                 };
 121         };
 122 };
 123
 124 &wmac {
 125         ralink,mtd-eeprom = <&factory 0>;
 126 };
 127
 128 &pinctrl {
 129         state_default: pinctrl0 {
 130                 gpio {
 131                         ralink,group = "i2c", "jtag", "uartf";
 132                         ralink,function = "gpio";
 133                 };
 134         };
 135 };