target/linux/ramips/dts/DAP-1522-A1.dts

   1 /dts-v1/;
   2
   3 #include "rt2880.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "dlink,dap-1522-a1", "ralink,rt2880-soc";
  10         model = "D-Link DAP-1522 A1";
  11
  12         cfi@bc400000 {
  13                 compatible = "cfi-flash";
  14                 reg = <0xbc400000 0x800000>;
  15                 bank-width = <2>;
  16                 device-width = <2>;
  17                 #address-cells = <1>;
  18                 #size-cells = <1>;
  19
  20                 partition@0 {
  21                         label = "uboot";
  22                         reg = <0x0 0x30000>;
  23                         read-only;
  24                 };
  25
  26                 factory: partition@30000 {
  27                         label = "factory";
  28                         reg = <0x30000 0x10000>;
  29                         read-only;
  30                 };
  31
  32                 partition@40000 {
  33                         label = "firmware";
  34                         reg = <0x40000 0x3a0000>;
  35                 };
  36         };
  37
  38         rtl8366s {
  39                 compatible = "realtek,rtl8366s";
  40                 gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
  41                 gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
  42         };
  43
  44         gpio-keys-polled {
  45                 compatible = "gpio-keys-polled";
  46                 #address-cells = <1>;
  47                 #size-cells = <0>;
  48                 poll-interval = <100>;
  49
  50                 reset {
  51                         label = "reset";
  52                         gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  53                         linux,code = <KEY_RESTART>;
  54                 };
  55
  56                 wps {
  57                         label = "wps";
  58                         gpios = <&gpio2 16 GPIO_ACTIVE_LOW>;
  59                         linux,code = <KEY_WPS_BUTTON>;
  60                 };
  61
  62                 ap {
  63                         label = "ap";
  64                         gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
  65                         linux,code = <BTN_0>;
  66                         linux,input-type = <EV_SW>;
  67                 };
  68
  69                 bridge {
  70                         label = "bridge";
  71                         gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
  72                         linux,code = <BTN_1>;
  73                         linux,input-type = <EV_SW>;
  74                 };
  75         };
  76
  77         gpio-leds {
  78                 compatible = "gpio-leds";
  79
  80                 wps {
  81                         label = "dap-1522-a1:blue:wps";
  82                         gpios = <&gpio2 17 GPIO_ACTIVE_LOW>;
  83                 };
  84
  85                 ap {
  86                         label = "dap-1522-a1:blue:ap";
  87                         gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
  88                 };
  89
  90                 sta {
  91                         label = "dap-1522-a1:red:sta";
  92                         gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
  93                 };
  94
  95                 status {
  96                         label = "dap-1522-a1:blue:status";
  97                         gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
  98                 };
  99         };
 100 };
 101
 102 &gpio0 {
 103         status = "okay";
 104 };
 105
 106 &gpio2 {
 107         status = "okay";
 108 };
 109
 110 &pinctrl {
 111         state_default: pinctrl0 {
 112                 gpio {
 113                         ralink,group = "i2c", "uartlite", "pci";
 114                         ralink,function = "gpio";
 115                 };
 116         };
 117 };
 118
 119 &ethernet {
 120         status = "okay";
 121         mtd-mac-address = <&factory 0x2004>;
 122
 123         port@0 {
 124                 mediatek,fixed-link = <1000 1 1 1>;
 125         };
 126
 127         mdio-bus {
 128                 status = "okay";
 129
 130                 phy0: ethernet-phy@0 {
 131                         phy-mode = "mii";
 132                         reg = <0>;
 133                 };
 134         };
 135 };
 136
 137 &wmac {
 138         ralink,mtd-eeprom = <&factory 0x2000>;
 139 };