5 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
8 /* the power led can't be controlled, use the wps led instead */
20 reg = <0x0 0x4000000>;
24 gpio: pinmux@E100B10 {
25 pinctrl-names = "default";
26 pinctrl-0 = <&state_default>;
28 state_default: pinmux {
30 lantiq,groups = "mdio";
31 lantiq,function = "mdio";
34 lantiq,groups = "gphy0 led1", "gphy1 led1";
35 lantiq,function = "gphy";
37 lantiq,open-drain = <0>;
43 lantiq,open-drain = <0>;
47 lantiq,groups = "spi", "spi_cs4";
48 lantiq,function = "spi";
61 compatible = "lantiq,xrx200-net";
62 reg = < 0xE108000 0x3000 /* switch */
63 0xE10B100 0x70 /* mdio */
64 0xE10B1D8 0x30 /* mii */
65 0xE10B308 0x30 /* pmac */
67 interrupt-parent = <&icu0>;
71 compatible = "lantiq,xrx200-pdi";
75 mtd-mac-address = <&ath9k_cal 0xf100>;
79 compatible = "lantiq,xrx200-pdi-port";
83 // gpios = <&gpio 42 1>;
86 compatible = "lantiq,xrx200-pdi-port";
92 compatible = "lantiq,xrx200-pdi-port";
95 phy-handle = <&phy11>;
98 compatible = "lantiq,xrx200-pdi-port";
101 phy-handle = <&phy13>;
106 #address-cells = <1>;
108 compatible = "lantiq,xrx200-mdio";
109 phy0: ethernet-phy@0 {
111 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
113 phy5: ethernet-phy@5 {
115 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
117 phy11: ethernet-phy@11 {
119 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
121 phy13: ethernet-phy@13 {
123 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
130 gpios = <&gpio 33 0>;
131 lantiq,portmask = <0x3>;
136 gpios = <&gpio 33 0>;
141 compatible = "lantiq,phy-xrx200";
142 firmware = "lantiq/vr9_phy11g_a2x.bin";
147 compatible = "lantiq,pcie-xway";
151 compatible = "ath9k,eeprom";
152 ath,eep-flash = <&ath9k_cal 0x21000>;
153 ath,mac-offset = <0xf100>;
161 compatible = "gpio-keys-polled";
162 #address-cells = <1>;
164 poll-interval = <100>;
168 linux,code = <0x198>;
175 linux,input-type = <5>; /* EV_SW */
180 gpios = <&gpio 39 1>;
181 linux,code = <0x211>;
186 compatible = "gpio-leds";
188 power is not controllable via gpio
191 label = "tdw89x0:green:dsl";
195 label = "tdw89x0:green:internet";
199 label = "tdw89x0:green:usb";
200 gpios = <&gpio 19 0>;
203 label = "tdw89x0:green:usb2";
204 gpios = <&gpio 20 0>;
207 label = "tdw89x0:green:wps";
208 gpios = <&gpio 37 0>;
217 #address-cells = <1>;
219 compatible = "jedec,spi-nor";
221 spi-max-frequency = <33250000>;
231 reg = <0x20000 0x7a0000>;
236 reg = <0x7c0000 0x10000>;
241 ath9k_cal: partition@7d0000 {
242 reg = <0x7d0000 0x30000>;
243 label = "boardconfig";