5 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
15 compatible = "lantiq,fpi", "simple-bus";
16 ranges = <0x0 0x10000000 0xEEFFFFF>;
17 reg = <0x10000000 0xEF00000>;
22 compatible = "lantiq,localbus", "simple-bus";
27 compatible = "lantiq,spi-xway-broken";
28 reg = <0xE100800 0x100>;
29 interrupt-parent = <&icu0>;
30 interrupts = <22 23 24>;
37 compatible = "s25fl129p0";
39 linux,modalias = "m25p80", "mx25l3205d";
40 spi-max-frequency = <1000000>;
44 label = "SPI (RO) U-Boot Image";
49 reg = <0x20000 0x10000>;
55 reg = <0x30000 0x10000>;
61 reg = <0x40000 0x10000>;
67 reg = <0x50000 0x003a0000>;
73 gpio: pinmux@E100B10 {
74 compatible = "lantiq,pinctrl-xr9";
75 pinctrl-names = "default";
76 pinctrl-0 = <&state_default>;
78 interrupt-parent = <&icu0>;
79 interrupts = <166 135 66 40 41 42 38>;
83 reg = <0xE100B10 0xA0>;
85 state_default: pinmux {
87 lantiq,groups = "exin3";
88 lantiq,function = "exin";
91 lantiq,groups = "stp";
92 lantiq,function = "stp";
95 lantiq,groups = "spi", "spi_cs4";
96 lantiq,function = "spi";
99 lantiq,groups = "nand cle", "nand ale",
100 "nand rd", "nand rdy";
101 lantiq,function = "ebu";
104 lantiq,groups = "mdio";
105 lantiq,function = "mdio";
108 lantiq,groups = "gnt1", "req1";
109 lantiq,function = "pci";
112 lantiq,pins = "io24", "io13", "io49", /* nand cle, ale and rd */
113 "io4", "io5", "io6", /* stp */
121 lantiq,pins = "io38";
126 lantiq,pins = "io39", /* exin3 */
127 "io48"; /* nand rdy */
134 #address-cells = <1>;
136 compatible = "lantiq,xrx200-net";
137 reg = < 0xE108000 0x3000 /* switch */
138 0xE10B100 0x70 /* mdio */
139 0xE10B1D8 0x30 /* mii */
140 0xE10B308 0x30 /* pmac */
142 interrupt-parent = <&icu0>;
143 interrupts = <73 72>;
146 compatible = "lantiq,xrx200-pdi";
147 #address-cells = <1>;
150 mac-address = [ 00 11 22 33 44 55 ];
153 compatible = "lantiq,xrx200-pdi-port";
156 phy-handle = <&phy0>;
159 compatible = "lantiq,xrx200-pdi-port";
162 phy-handle = <&phy1>;
165 compatible = "lantiq,xrx200-pdi-port";
168 phy-handle = <&phy11>;
173 compatible = "lantiq,xrx200-pdi";
174 #address-cells = <1>;
177 mac-address = [ 00 11 22 33 44 56 ];
180 compatible = "lantiq,xrx200-pdi-port";
183 phy-handle = <&phy5>;
188 compatible = "lantiq,xrx200-pdi";
189 #address-cells = <1>;
192 mac-address = [ 00 11 22 33 44 57 ];
194 compatible = "lantiq,xrx200-pdi-port";
197 phy-handle = <&phy13>;
202 #address-cells = <1>;
204 compatible = "lantiq,xrx200-mdio";
205 phy0: ethernet-phy@0 {
207 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
208 lantiq,c45-reg-init = <1 0 0 0>;
210 phy1: ethernet-phy@1 {
212 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
213 lantiq,c45-reg-init = <1 0 0 0>;
215 phy5: ethernet-phy@5 {
217 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
218 lantiq,c45-reg-init = <1 0 0 0>;
220 phy11: ethernet-phy@11 {
222 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
223 lantiq,c45-reg-init = <1 0 0 0>;
225 phy13: ethernet-phy@13 {
227 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
228 lantiq,c45-reg-init = <1 0 0 0>;
234 compatible = "lantiq,gpio-stp-xway";
235 reg = <0xE100BB0 0x40>;
239 lantiq,shadow = <0xffff>;
240 lantiq,groups = <0x7>;
249 gpios = <&gpio 33 0>;
250 lantiq,portmask = <0x3>;
254 #address-cells = <3>;
256 #interrupt-cells = <1>;
257 compatible = "lantiq,pci-xway1";
258 bus-range = <0x0 0x0>;
259 ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000 /* pci memory */
260 0x1000000 0 0x00000000 0xAE00000 0 0x200000>; /* io space */
261 reg = <0x7000000 0x8000 /* config space */
262 0xE105400 0x400>; /* pci bridge */
263 lantiq,bus-clock = <33333333>;
264 /*lantiq,external-clock;*/
265 lantiq,delay-hi = <0>; /* 0ns delay */
266 lantiq,delay-lo = <0>; /* 0.0ns delay */
267 interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
269 0x7000 0 0 1 &icu0 29 1 // slot 14, irq 29
271 gpios-reset = <&gpio 21 0>;
272 req-mask = <0x1>; /* GNT1 */
277 compatible = "lantiq,phy-xrx200";
278 firmware = "lantiq/vr9_phy11g_a2x.bin";
283 compatible = "gpio-keys-polled";
284 #address-cells = <1>;
286 poll-interval = <100>;
290 linux,code = <0x198>;
294 gpios = <&gpio 11 1>;
295 linux,code = <0x100>;
300 compatible = "gpio-leds";
305 default-state = "on";