6 model = "BTHOMEHUBV5A - BT Home Hub 5A";
9 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
13 failsafe = &power_red;
14 running = &power_blue;
16 internet = &broadband_blue;
17 wifi = &wireless_blue;
22 reg = <0x0 0x8000000>;
28 compatible = "gen_nand", "lantiq,nand-xway";
31 reg = <0x1 0x0 0x2000000>;
42 reg = <0x40000 0x40000>;
44 caldata: partition@80000 {
46 reg = <0x80000 0x20000>;
51 reg = <0xa0000 0x200000>;
55 reg = <0x2a0000 0x7d60000>;
60 gpio: pinmux@E100B10 {
61 pinctrl-names = "default";
62 pinctrl-0 = <&state_default>;
64 interrupt-parent = <&icu0>;
65 interrupts = <166 135 66 40 41 42 38>;
67 state_default: pinmux {
69 lantiq,groups = "mdio";
70 lantiq,function = "mdio";
86 lantiq,open-drain = <0>;
90 lantiq,groups = "nand cle", "nand ale";
91 lantiq,function = "ebu";
93 lantiq,open-drain = <0>;
97 lantiq,groups = "nand cs1";
98 lantiq,function = "ebu";
99 lantiq,open-drain = <0>;
107 gpios = <&gpio 33 0>;
112 lantiq,bus-clock = <33333333>;
113 interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
114 interrupt-map = <0x7000 0 0 1 &icu0 30 1>;
115 gpio-reset = <&gpio 21 0>;
120 compatible = "lantiq,phy-xrx200";
121 firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
122 firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
127 compatible = "ath9k,eeprom";
128 ath,eep-flash = <&caldata 0x1000>;
129 ath,mac-offset = <0x110c>;
130 ath,mac-increment = <2>;
131 ath,pci-slot = <0xe>; /* 14 */
135 compatible = "gpio-keys-polled";
136 #address-cells = <1>;
138 poll-interval = <100>;
143 linux,code = <0x198>;
148 gpios = <&gpio 25 1>;
149 linux,code = <0x211>;
154 gpios = <&gpio 39 1>;
155 linux,code = <0x198>;
160 compatible = "gpio-leds";
162 /* broadband-* is a single RGB led */
164 label = "bthomehubv5a:red:broadband";
168 label = "bthomehubv5a:green:broadband";
171 broadband_blue: broadband-blue {
172 label = "bthomehubv5a:blue:broadband";
176 /* wireless-* is a single RGB led */
178 label = "bthomehubv5a:red:wireless";
182 label = "bthomehubv5a:green:wireless";
183 gpios = <&gpio 10 1>;
185 wireless_blue: wireless-blue {
186 label = "bthomehubv5a:blue:wireless";
187 gpios = <&gpio 11 1>;
190 /* power-* is a single RGB led */
191 power_red: power-red {
192 label = "bthomehubv5a:red:power";
193 gpios = <&gpio 12 1>;
195 power_green: power-green {
196 label = "bthomehubv5a:green:power";
197 gpios = <&gpio 14 1>;
198 default-state = "keep";
200 power_blue: power-blue {
201 label = "bthomehubv5a:blue:power";
202 gpios = <&gpio 15 1>;
207 gpios = <&gpio 19 0>;
214 compatible = "lantiq,xrx200-pdi";
215 #address-cells = <1>;
218 mtd-mac-address = <&caldata 0x110c>;
222 compatible = "lantiq,xrx200-pdi-port";
225 phy-handle = <&phy0>;
228 compatible = "lantiq,xrx200-pdi-port";
231 phy-handle = <&phy1>;
234 compatible = "lantiq,xrx200-pdi-port";
237 phy-handle = <&phy11>;
240 compatible = "lantiq,xrx200-pdi-port";
243 phy-handle = <&phy13>;
248 compatible = "lantiq,xrx200-pdi";
249 #address-cells = <1>;
252 mtd-mac-address = <&caldata 0x110c>;
253 mtd-mac-address-increment = <4>;
257 compatible = "lantiq,xrx200-pdi-port";
260 phy-handle = <&phy5>;
265 #address-cells = <1>;
267 compatible = "lantiq,xrx200-mdio";
269 phy0: ethernet-phy@0 {
271 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
273 phy1: ethernet-phy@1 {
275 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
277 phy5: ethernet-phy@5 {
279 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
281 phy11: ethernet-phy@11 {
283 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
285 phy13: ethernet-phy@13 {
287 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";