6 model = "BTHOMEHUBV5A - BT Home Hub 5A";
9 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
13 led-boot = &power_green;
14 led-failsafe = &power_red;
15 led-running = &power_blue;
17 led-internet = &broadband_blue;
18 led-wifi = &wireless_blue;
22 reg = <0x0 0x8000000>;
28 compatible = "gen_nand", "lantiq,nand-xway";
31 reg = <0x1 0x0 0x2000000>;
36 compatible = "fixed-partitions";
47 reg = <0x40000 0x40000>;
49 caldata: partition@80000 {
51 reg = <0x80000 0x20000>;
56 reg = <0xa0000 0x200000>;
60 reg = <0x2a0000 0x7d60000>;
66 gpio: pinmux@E100B10 {
67 pinctrl-names = "default";
68 pinctrl-0 = <&state_default>;
70 interrupt-parent = <&icu0>;
71 interrupts = <166 135 66 40 41 42 38>;
73 state_default: pinmux {
75 lantiq,groups = "mdio";
76 lantiq,function = "mdio";
92 lantiq,open-drain = <0>;
96 lantiq,groups = "nand cle", "nand ale";
97 lantiq,function = "ebu";
99 lantiq,open-drain = <0>;
103 lantiq,groups = "nand cs1";
104 lantiq,function = "ebu";
105 lantiq,open-drain = <0>;
113 gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
118 lantiq,bus-clock = <33333333>;
119 interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
120 interrupt-map = <0x7000 0 0 1 &icu0 30 1>;
121 gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
126 compatible = "lantiq,phy-xrx200";
127 firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
128 firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
133 compatible = "ath9k,eeprom";
134 ath,eep-flash = <&caldata 0x1000>;
135 ath,mac-offset = <0x110c>;
136 ath,mac-increment = <2>;
137 ath,pci-slot = <0xe>; /* 14 */
141 compatible = "gpio-keys-polled";
142 #address-cells = <1>;
144 poll-interval = <100>;
148 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
149 linux,code = <KEY_RESTART>;
154 gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
155 linux,code = <KEY_WPS_BUTTON>;
160 gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
161 linux,code = <KEY_POWER>;
166 compatible = "gpio-leds";
168 /* broadband-* is a single RGB led */
170 label = "bthomehubv5a:red:broadband";
171 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
174 label = "bthomehubv5a:green:broadband";
175 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
177 broadband_blue: broadband-blue {
178 label = "bthomehubv5a:blue:broadband";
179 gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
182 /* wireless-* is a single RGB led */
184 label = "bthomehubv5a:red:wireless";
185 gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
188 label = "bthomehubv5a:green:wireless";
189 gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
191 wireless_blue: wireless-blue {
192 label = "bthomehubv5a:blue:wireless";
193 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
196 /* power-* is a single RGB led */
197 power_red: power-red {
198 label = "bthomehubv5a:red:power";
199 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
201 power_green: power-green {
202 label = "bthomehubv5a:green:power";
203 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
204 default-state = "keep";
206 power_blue: power-blue {
207 label = "bthomehubv5a:blue:power";
208 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
213 gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
220 compatible = "lantiq,xrx200-pdi";
221 #address-cells = <1>;
224 mtd-mac-address = <&caldata 0x110c>;
228 compatible = "lantiq,xrx200-pdi-port";
231 phy-handle = <&phy0>;
234 compatible = "lantiq,xrx200-pdi-port";
237 phy-handle = <&phy1>;
240 compatible = "lantiq,xrx200-pdi-port";
243 phy-handle = <&phy11>;
246 compatible = "lantiq,xrx200-pdi-port";
249 phy-handle = <&phy13>;
254 compatible = "lantiq,xrx200-pdi";
255 #address-cells = <1>;
258 mtd-mac-address = <&caldata 0x110c>;
259 mtd-mac-address-increment = <4>;
263 compatible = "lantiq,xrx200-pdi-port";
266 phy-handle = <&phy5>;
271 #address-cells = <1>;
273 compatible = "lantiq,xrx200-mdio";
275 phy0: ethernet-phy@0 {
277 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
279 phy1: ethernet-phy@1 {
281 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
283 phy5: ethernet-phy@5 {
285 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
287 phy11: ethernet-phy@11 {
289 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
291 phy13: ethernet-phy@13 {
293 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";