1 #include "qcom-ipq8065.dtsi"
3 #include <dt-bindings/input/input.h>
6 model = "ZyXEL NBG6817";
7 compatible = "zyxel,nbg6817", "qcom,ipq8065", "qcom,ipq8064";
10 reg = <0x42000000 0x1e000000>;
11 device_type = "memory";
19 reg = <0x41200000 0x300000>;
25 serial0 = &gsbi4_serial;
30 led-failsafe = &power;
36 bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd";
37 stdout-path = "serial0:115200n8";
38 append-rootblock = "root=/dev/mmcblk0p";
43 button_pins: button_pins {
45 pins = "gpio53", "gpio54", "gpio65";
52 i2c4_pins: i2c4_pinmux {
54 pins = "gpio12", "gpio13";
56 drive-strength = <12>;
63 pins = "gpio9", "gpio26", "gpio33", "gpio64";
70 mdio0_pins: mdio0_pins {
72 pins = "gpio0", "gpio1";
84 rgmii2_pins: rgmii2_pins {
86 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
87 "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
94 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
101 pins = "gpio18", "gpio19", "gpio21";
103 drive-strength = <10>;
109 drive-strength = <12>;
113 usb0_pwr_en_pins: usb0_pwr_en_pins {
115 pins = "gpio16", "gpio17";
117 drive-strength = <12>;
132 usb1_pwr_en_pins: usb1_pwr_en_pins {
134 pins = "gpio14", "gpio15";
136 drive-strength = <12>;
153 qcom,mode = <GSBI_PROT_I2C_UART>;
159 * The i2c device on gsbi4 should not be enabled.
160 * On ipq806x designs gsbi4 i2c is meant for exclusive
161 * RPM usage. Turning this on in kernel manifests as
162 * i2c failure for the RPM.
166 gsbi5: gsbi@1a200000 {
167 qcom,mode = <GSBI_PROT_SPI>;
173 pinctrl-0 = <&spi_pins>;
174 pinctrl-names = "default";
176 cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
179 compatible = "jedec,spi-nor";
180 #address-cells = <1>;
182 spi-max-frequency = <51200000>;
186 compatible = "qcom,smem";
192 usb3_0: usb3@110f8800 {
195 pinctrl-0 = <&usb0_pwr_en_pins>;
196 pinctrl-names = "default";
199 usb3_1: usb3@100f8800 {
202 pinctrl-0 = <&usb1_pwr_en_pins>;
203 pinctrl-names = "default";
206 pcie0: pci@1b500000 {
208 reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
209 pinctrl-0 = <&pcie0_pins>;
210 pinctrl-names = "default";
213 pcie1: pci@1b700000 {
215 reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
216 pinctrl-0 = <&pcie1_pins>;
217 pinctrl-names = "default";
222 compatible = "virtual,mdio-gpio";
223 #address-cells = <1>;
225 gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
226 <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
227 pinctrl-0 = <&mdio0_pins>;
228 pinctrl-names = "default";
230 phy0: ethernet-phy@0 {
232 qca,ar8327-initvals = <
233 0x00004 0x7600000 /* PAD0_MODE */
234 0x00008 0x1000000 /* PAD5_MODE */
235 0x0000c 0x80 /* PAD6_MODE */
236 0x000e4 0xaa545 /* MAC_POWER_SEL */
237 0x000e0 0xc74164de /* SGMII_CTRL */
238 0x0007c 0x4e /* PORT0_STATUS */
239 0x00094 0x4e /* PORT6_STATUS */
240 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
241 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
242 0x00978 0x19008643 /* QM_PORT1_CTRL0 */
243 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
244 0x00980 0x19008643 /* QM_PORT2_CTRL0 */
245 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
246 0x00988 0x19008643 /* QM_PORT3_CTRL0 */
247 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
248 0x00990 0x19008643 /* QM_PORT4_CTRL0 */
249 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
250 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
251 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
252 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
253 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
257 phy4: ethernet-phy@4 {
259 qca,ar8327-initvals = <
260 0x000e4 0x6a545 /* MAC_POWER_SEL */
261 0x0000c 0x80 /* PAD6_MODE */
266 gmac1: ethernet@37200000 {
270 qcom,phy_mdio_addr = <4>;
271 qcom,poll_required = <0>;
272 qcom,rgmii_delay = <1>;
273 qcom,phy_mii_type = <0>;
274 qcom,emulation = <0>;
278 pinctrl-0 = <&rgmii2_pins>;
279 pinctrl-names = "default";
287 gmac2: ethernet@37400000 {
291 qcom,phy_mdio_addr = <0>; /* none */
292 qcom,poll_required = <0>; /* no polling */
293 qcom,rgmii_delay = <0>;
294 qcom,phy_mii_type = <1>;
295 qcom,emulation = <0>;
306 sdcc1: sdcc@12400000 {
313 compatible = "gpio-keys";
314 pinctrl-0 = <&button_pins>;
315 pinctrl-names = "default";
319 gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>;
320 linux,code = <KEY_RFKILL>;
321 linux,input-type = <EV_SW>;
326 gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
327 linux,code = <KEY_RESTART>;
332 gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
333 linux,code = <KEY_WPS_BUTTON>;
338 compatible = "gpio-leds";
339 pinctrl-0 = <&led_pins>;
340 pinctrl-names = "default";
343 label = "nbg6817:white:internet";
344 gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
348 label = "nbg6817:white:power";
349 gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
350 default-state = "keep";
354 label = "nbg6817:amber:wifi2g";
355 gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
358 /* wifi2g amber from the manual is missing */
361 label = "nbg6817:amber:wifi5g";
362 gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
365 /* wifi5g amber from the manual is missing */