1 include $(TOPDIR)/rules.mk
2 include $(INCLUDE_DIR)/image.mk
4 DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
8 KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
9 KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
10 KERNEL_PREFIX := $$(IMAGE_PREFIX)
11 KERNEL_LOADADDR := 0x80208000
12 SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
13 IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
14 IMAGE/sysupgrade.bin/squashfs :=
17 define Device/FitImage
18 KERNEL_SUFFIX := -fit-uImage.itb
19 KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
23 define Device/FitImageLzma
24 KERNEL_SUFFIX := -fit-uImage.itb
25 KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
29 define Device/FitzImage
30 KERNEL_SUFFIX := -fit-zImage.itb
31 KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
37 IMAGES := nand-factory.ubi nand-sysupgrade.bin
38 IMAGE/nand-factory.ubi := append-ubi
39 IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
42 define Device/DniImage
43 KERNEL_SUFFIX := -fit-uImage.itb
44 KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
48 IMAGES := factory.img sysupgrade.bin
49 IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
50 IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | append-metadata
52 DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
55 -$(STAGING_DIR_HOST)/bin/mksenaofw \
56 -n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
57 -c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
63 define Device/8dev_jalapeno
64 $(call Device/FitImage)
66 DEVICE_VENDOR := 8devices
67 DEVICE_MODEL := Jalapeno
68 DEVICE_DTS := qcom-ipq4018-jalapeno
72 TARGET_DEVICES += 8dev_jalapeno
74 define Device/alfa-network_ap120c-ac
75 $(call Device/FitImage)
77 DEVICE_VENDOR := ALFA Network
78 DEVICE_MODEL := AP120C-AC
79 DEVICE_DTS := qcom-ipq4018-ap120c-ac
80 DEVICE_PACKAGES := kmod-usb-acm \
81 kmod-tpm-i2c-atmel uboot-envtools
85 IMAGES := nand-factory.bin nand-sysupgrade.bin
86 IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
88 TARGET_DEVICES += alfa-network_ap120c-ac
90 define Device/asus_map-ac2200
91 $(call Device/FitImageLzma)
93 DEVICE_MODEL := Lyra (MAP-AC2200)
94 DEVICE_DTS := qcom-ipq4019-map-ac2200
95 IMAGES := sysupgrade.bin
96 DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k
98 TARGET_DEVICES += asus_map-ac2200
100 define Device/asus_rt-ac58u
101 $(call Device/FitImageLzma)
102 DEVICE_VENDOR := ASUS
103 DEVICE_MODEL := RT-AC58U
104 DEVICE_DTS := qcom-ipq4018-rt-ac58u
108 IMAGE_SIZE := 20439364
109 FILESYSTEMS := squashfs
110 # Someone - in their infinite wisdom - decided to put the firmware
111 # version in front of the image name \03\00\00\04 => Version 3.0.0.4
112 # Since u-boot works with strings we either need another fixup step
113 # to add a version... or we are very careful not to add '\0' into that
114 # string and call it a day.... Yeah, we do the latter!
115 UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
116 IMAGES := sysupgrade.bin
117 DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
119 TARGET_DEVICES += asus_rt-ac58u
121 define Device/avm_fritzbox-4040
122 $(call Device/FitImageLzma)
124 DEVICE_MODEL := FRITZ!Box 4040
125 DEVICE_DTS := qcom-ipq4018-fritz4040
126 BOARD_NAME := fritz4040
128 UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
129 UBOOT_PARTITION_SIZE := 524288
130 IMAGES = eva.bin sysupgrade.bin
131 IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
132 IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
133 DEVICE_PACKAGES := fritz-tffs fritz-caldata
135 TARGET_DEVICES += avm_fritzbox-4040
137 define Device/avm_fritzbox-7530
138 $(call Device/FitImageLzma)
140 DEVICE_MODEL := FRITZ!Box 7530
141 DEVICE_DTS := qcom-ipq4019-fritzbox-7530
142 DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
143 IMAGES := sysupgrade.bin
145 TARGET_DEVICES += avm_fritzbox-7530
147 define Device/avm_fritzrepeater-1200
148 $(call Device/FitImageLzma)
150 DEVICE_MODEL := FRITZ!Repeater 1200
151 DEVICE_DTS := qcom-ipq4019-fritzrepeater-1200
152 DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-1200
153 IMAGES := sysupgrade.bin
155 TARGET_DEVICES += avm_fritzrepeater-1200
157 define Device/avm_fritzrepeater-3000
158 $(call Device/FitImageLzma)
160 DEVICE_MODEL := FRITZ!Repeater 3000
161 DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000
162 DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand
163 IMAGES := sysupgrade.bin
165 TARGET_DEVICES += avm_fritzrepeater-3000
167 define Device/compex_wpj419
168 $(call Device/FitImage)
169 $(call Device/UbiFit)
170 DEVICE_VENDOR := Compex
171 DEVICE_MODEL := WPJ419
172 DEVICE_DTS := qcom-ipq4019-wpj419
173 DEVICE_DTS_CONFIG := config@12
177 FILESYSTEMS := squashfs
179 TARGET_DEVICES += compex_wpj419
181 define Device/compex_wpj428
182 $(call Device/FitImage)
183 DEVICE_VENDOR := Compex
184 DEVICE_MODEL := WPJ428
185 DEVICE_DTS := qcom-ipq4028-wpj428
186 DEVICE_DTS_CONFIG := config@4
190 IMAGES = sysupgrade.bin
191 IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
192 DEVICE_PACKAGES := kmod-gpio-beeper
194 TARGET_DEVICES += compex_wpj428
196 define Device/engenius_eap1300
197 $(call Device/FitImage)
198 DEVICE_VENDOR := EnGenius
199 DEVICE_MODEL := EAP1300
200 DEVICE_DTS_CONFIG := config@4
201 BOARD_NAME := eap1300
202 DEVICE_DTS := qcom-ipq4018-eap1300
205 IMAGES := sysupgrade.bin
206 IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
208 TARGET_DEVICES += engenius_eap1300
210 define Device/engenius_ens620ext
211 $(call Device/FitImage)
212 DEVICE_VENDOR := EnGenius
213 DEVICE_MODEL := ENS620EXT
214 DEVICE_DTS := qcom-ipq4018-ens620ext
215 DEVICE_DTS_CONFIG := config@4
218 BOARD_NAME := ENS620EXT
221 PRODUCT_ID_NEW := 0xA4
228 FILESYSTEMS := squashfs
229 IMAGES := sysupgrade.bin factory_30.bin factory_35.bin
230 IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | append-metadata
231 IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
232 IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
234 TARGET_DEVICES += engenius_ens620ext
236 define Device/glinet_gl-b1300
237 $(call Device/FitImage)
238 DEVICE_VENDOR := GL.iNet
239 DEVICE_MODEL := GL-B1300
240 BOARD_NAME := gl-b1300
241 DEVICE_DTS := qcom-ipq4029-gl-b1300
244 IMAGES := sysupgrade.bin
245 IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
247 TARGET_DEVICES += glinet_gl-b1300
249 define Device/linksys_ea6350v3
250 # The Linksys EA6350v3 has a uboot bootloader that does not
251 # support either booting lzma kernel images nor booting UBI
252 # partitions. This uboot, however, supports raw kernel images and
255 # As for the time of writing this, the device will boot the kernel
256 # from a fixed address with a fixed length of 3MiB. Also, the
257 # device has a hard-coded kernel command line that requieres the
258 # rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
259 # Oh... and the kernel partition overlaps with the rootfs
260 # partition (the same for alt_kernel and alt_rootfs).
262 # If you are planing re-partitioning the device, you may want to
263 # keep those details in mind:
264 # 1. The kernel adresses you should honor are 0x00000000 and
265 # 0x02800000 respectively.
266 # 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
267 # 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
268 # 4. The kernel command line from uboot is harcoded to boot with
269 # rootfs either in mtd11 or mtd13.
270 $(call Device/FitzImage)
271 DEVICE_VENDOR := Linksys
272 DEVICE_MODEL := EA6350
274 DEVICE_DTS := qcom-ipq4018-ea6350v3
280 IMAGES := factory.bin sysupgrade.bin
281 IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA6350v3
282 DEVICE_PACKAGES := uboot-envtools
284 TARGET_DEVICES += linksys_ea6350v3
286 define Device/linksys_ea8300
287 $(call Device/FitzImage)
288 DEVICE_VENDOR := Linksys
289 DEVICE_MODEL := EA8300
290 DEVICE_DTS := qcom-ipq4019-linksys_ea8300
295 UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
296 IMAGES := sysupgrade.bin factory.bin
297 IMAGE/factory.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA8300
298 DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
300 TARGET_DEVICES += linksys_ea8300
302 define Device/meraki_mr33
303 $(call Device/FitImage)
304 DEVICE_VENDOR := Cisco Meraki
306 DEVICE_DTS := qcom-ipq4029-mr33
309 IMAGES = sysupgrade.bin
310 DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
312 TARGET_DEVICES += meraki_mr33
314 define Device/netgear_ex61x0v2
315 $(call Device/DniImage)
316 DEVICE_DTS_CONFIG := config@4
317 NETGEAR_BOARD_ID := EX6150v2series
318 NETGEAR_HW_ID := 29765285+16+0+128+2x2
321 define Device/netgear_ex6100v2
322 $(call Device/netgear_ex61x0v2)
323 DEVICE_VENDOR := Netgear
324 DEVICE_MODEL := EX6100
326 DEVICE_DTS := qcom-ipq4018-ex6100v2
328 TARGET_DEVICES += netgear_ex6100v2
330 define Device/netgear_ex6150v2
331 $(call Device/netgear_ex61x0v2)
332 DEVICE_VENDOR := Netgear
333 DEVICE_MODEL := EX6150
335 DEVICE_DTS := qcom-ipq4018-ex6150v2
337 TARGET_DEVICES += netgear_ex6150v2
339 define Device/openmesh_a42
340 $(call Device/FitImageLzma)
341 DEVICE_VENDOR := OpenMesh
343 DEVICE_DTS := qcom-ipq4018-a42
344 DEVICE_DTS_CONFIG := config@om.a42
346 KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
348 IMAGES = factory.bin sysupgrade.bin
349 IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
350 IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
351 DEVICE_PACKAGES := uboot-envtools
353 TARGET_DEVICES += openmesh_a42
355 define Device/openmesh_a62
356 $(call Device/FitImageLzma)
357 DEVICE_VENDOR := OpenMesh
359 DEVICE_DTS := qcom-ipq4019-a62
360 DEVICE_DTS_CONFIG := config@om.a62
362 KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
364 IMAGES = factory.bin sysupgrade.bin
365 IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
366 IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
367 DEVICE_PACKAGES := ath10k-firmware-qca9888-ct uboot-envtools
370 TARGET_DEVICES += openmesh_a62
372 define Device/qcom_ap-dk01.1-c1
373 DEVICE_VENDOR := Qualcomm Atheros
374 DEVICE_MODEL := AP-DK01.1
376 BOARD_NAME := ap-dk01.1-c1
377 DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
381 $(call Device/FitImage)
382 IMAGES := sysupgrade.bin
383 IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
385 TARGET_DEVICES += qcom_ap-dk01.1-c1
387 define Device/qcom_ap-dk04.1-c1
388 $(call Device/FitImage)
389 $(call Device/UbiFit)
390 DEVICE_VENDOR := Qualcomm Atheros
391 DEVICE_MODEL := AP-DK04.1
393 DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
398 BOARD_NAME := ap-dk04.1-c1
400 TARGET_DEVICES += qcom_ap-dk04.1-c1
402 define Device/qxwlan_e2600ac-c1
403 $(call Device/FitImage)
404 DEVICE_VENDOR := Qxwlan
405 DEVICE_MODEL := E2600AC
407 BOARD_NAME := e2600ac-c1
408 DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c1
411 IMAGES := sysupgrade.bin
412 IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
413 DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
415 TARGET_DEVICES += qxwlan_e2600ac-c1
417 define Device/qxwlan_e2600ac-c2
418 $(call Device/FitImage)
419 $(call Device/UbiFit)
420 DEVICE_VENDOR := Qxwlan
421 DEVICE_MODEL := E2600AC
423 DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c2
427 DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
429 TARGET_DEVICES += qxwlan_e2600ac-c2
431 define Device/unielec_u4019-32m
432 $(call Device/FitImage)
433 DEVICE_VENDOR := Unielec
434 DEVICE_MODEL := U4019
435 DEVICE_VARIANT := 32M
436 BOARD_NAME := u4019-32m
437 DEVICE_DTS := qcom-ipq4019-unielec-u4019-32m
440 IMAGES := sysupgrade.bin
441 IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
443 TARGET_DEVICES += unielec_u4019-32m
445 define Device/zyxel_nbg6617
446 $(call Device/FitImageLzma)
447 DEVICE_VENDOR := ZyXEL
448 DEVICE_MODEL := NBG6617
449 DEVICE_DTS := qcom-ipq4018-nbg6617
450 ROOTFS_SIZE := 24960k
452 RAS_ROOTFS_SIZE := 19840k
453 RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
454 IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
455 IMAGES := sysupgrade.bin factory.bin
456 # The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
457 # at least as large as the one of the initial firmware image (not the current
458 # one on the device). This only applies to the Web-UI, the bootlaoder ignores
459 # this minimum-size. However, the larger image can be flashed both ways.
460 IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
461 IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
462 DEVICE_PACKAGES := uboot-envtools kmod-usb-ledtrig-usbport
464 TARGET_DEVICES += zyxel_nbg6617
466 define Device/zyxel_wre6606
467 $(call Device/FitImage)
468 DEVICE_VENDOR := ZyXEL
469 DEVICE_MODEL := WRE6606
470 DEVICE_DTS_CONFIG := config@4
471 DEVICE_DTS := qcom-ipq4018-wre6606
472 IMAGES := sysupgrade.bin
473 IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
475 TARGET_DEVICES += zyxel_wre6606
477 $(eval $(call BuildImage))