2 * Copyright 2013 Gateworks Corporation
4 * The code contained herein is licensed under the GNU General Public
5 * License. You may obtain a copy of the GNU General Public License
6 * Version 2 or later at the following locations:
8 * http://www.opensource.org/licenses/gpl-license.html
9 * http://www.gnu.org/copyleft/gpl.html
16 model = "Gateworks Ventana GW5400-A";
17 compatible = "gw,imx6q-gw5400-a", "gw,ventana", "fsl,imx6q";
19 /* these are used by bootloader for disabling nodes */
38 bootargs = "console=ttymxc1,115200";
42 reg = <0x10000000 0x40000000>;
46 compatible = "gpio-leds";
50 gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */
52 linux,default-trigger = "heartbeat";
57 gpios = <&gpio4 10 0>; /* 106 -> MX6_PANLEDR */
58 default-state = "off";
63 gpios = <&gpio4 15 1>; /* 111 -> MX6_LOCLED# */
64 default-state = "off";
69 compatible = "simple-bus";
72 compatible = "regulator-fixed";
73 regulator-name = "1P0V";
74 regulator-min-microvolt = <1000000>;
75 regulator-max-microvolt = <1000000>;
80 compatible = "regulator-fixed";
81 regulator-name = "3P3V";
82 regulator-min-microvolt = <3300000>;
83 regulator-max-microvolt = <3300000>;
87 reg_usb_h1_vbus: usb_h1_vbus {
88 compatible = "regulator-fixed";
89 regulator-name = "usb_h1_vbus";
90 regulator-min-microvolt = <5000000>;
91 regulator-max-microvolt = <5000000>;
95 reg_usb_otg_vbus: usb_otg_vbus {
96 compatible = "regulator-fixed";
97 regulator-name = "usb_otg_vbus";
98 regulator-min-microvolt = <5000000>;
99 regulator-max-microvolt = <5000000>;
100 gpio = <&gpio3 22 0>;
106 compatible = "fsl,imx6q-sabrelite-sgtl5000",
107 "fsl,imx-audio-sgtl5000";
108 model = "imx6q-sabrelite-sgtl5000";
109 ssi-controller = <&ssi1>;
110 audio-codec = <&codec>;
112 "MIC_IN", "Mic Jack",
113 "Mic Jack", "Mic Bias",
114 "Headphone Jack", "HP_OUT";
121 pinctrl-names = "default";
122 pinctrl-0 = <&pinctrl_audmux_1>;
127 fsl,spi-num-chipselects = <1>;
128 cs-gpios = <&gpio3 19 0>;
129 pinctrl-names = "default";
130 pinctrl-0 = <&pinctrl_ecspi1_1>;
134 compatible = "sst,w25q256";
135 spi-max-frequency = <30000000>;
141 pinctrl-names = "default";
142 pinctrl-0 = <&pinctrl_enet_1>;
144 phy-reset-gpios = <&gpio1 30 0>;
149 clock-frequency = <100000>;
150 pinctrl-names = "default";
151 pinctrl-0 = <&pinctrl_i2c1_1>;
155 compatible = "atmel,24c02";
161 compatible = "atmel,24c02";
167 compatible = "atmel,24c02";
173 compatible = "atmel,24c02";
179 compatible = "nxp,pca9555";
186 compatible = "gw,gsp";
191 compatible = "dallas,ds1672";
197 clock-frequency = <100000>;
198 pinctrl-names = "default";
199 pinctrl-0 = <&pinctrl_i2c2_2>;
203 compatible = "fsl,pfuze100";
208 regulator-min-microvolt = <300000>;
209 regulator-max-microvolt = <1875000>;
212 regulator-ramp-delay = <6250>;
216 regulator-min-microvolt = <300000>;
217 regulator-max-microvolt = <1875000>;
220 regulator-ramp-delay = <6250>;
224 regulator-min-microvolt = <800000>;
225 regulator-max-microvolt = <3950000>;
231 regulator-min-microvolt = <400000>;
232 regulator-max-microvolt = <1975000>;
238 regulator-min-microvolt = <400000>;
239 regulator-max-microvolt = <1975000>;
245 regulator-min-microvolt = <800000>;
246 regulator-max-microvolt = <3300000>;
250 regulator-min-microvolt = <5000000>;
251 regulator-max-microvolt = <5150000>;
255 regulator-min-microvolt = <1000000>;
256 regulator-max-microvolt = <3000000>;
267 regulator-min-microvolt = <800000>;
268 regulator-max-microvolt = <1550000>;
272 regulator-min-microvolt = <800000>;
273 regulator-max-microvolt = <1550000>;
277 regulator-min-microvolt = <1800000>;
278 regulator-max-microvolt = <3300000>;
282 regulator-min-microvolt = <1800000>;
283 regulator-max-microvolt = <3300000>;
288 regulator-min-microvolt = <1800000>;
289 regulator-max-microvolt = <3300000>;
294 regulator-min-microvolt = <1800000>;
295 regulator-max-microvolt = <3300000>;
301 pciswitch: pex8609@3f {
302 compatible = "plx,pex8609";
306 pciclkgen: si52147@6b {
307 compatible = "sil,si52147";
313 clock-frequency = <100000>;
314 pinctrl-names = "default";
315 pinctrl-0 = <&pinctrl_i2c3_2>;
318 accelerometer: mma8450@1c {
319 compatible = "fsl,mma8450";
324 compatible = "fsl,sgtl5000";
326 clocks = <&clks 169>;
327 VDDA-supply = <&sw4_reg>;
328 VDDIO-supply = <®_3p3v>;
332 compatible = "adi,adv7611";
336 touchscreen: egalax_ts@04 {
337 compatible = "eeti,egalax_ts";
339 interrupt-parent = <&gpio7>;
340 interrupts = <12 2>; /* gpio7_12 active low */
341 wakeup-gpios = <&gpio7 12 0>;
344 videoout: adv7393@2a {
345 compatible = "adi,adv7393";
349 videoin: adv7180@20 {
350 compatible = "adi,adv7180";
356 pinctrl-names = "default";
357 pinctrl-0 = <&pinctrl_hog>;
360 pinctrl_hog: hoggrp {
362 MX6Q_PAD_EIM_D22__GPIO3_IO22 0x80000000 /* OTG_PWR_EN */
363 MX6Q_PAD_EIM_D19__GPIO3_IO19 0x80000000 /* SPINOR_CS0# */
364 MX6Q_PAD_ENET_TX_EN__GPIO1_IO28 0x80000000 /* PCIE IRQ */
365 MX6Q_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 /* PCIE RST */
366 MX6Q_PAD_GPIO_0__CCM_CLKO1 0x000130b0 /* AUD4_MCK */
367 MX6Q_PAD_GPIO_17__GPIO7_IO12 0x80000000 /* TOUCH_IRQ# */
368 MX6Q_PAD_KEY_COL0__GPIO4_IO06 0x80000000 /* user1 led */
369 MX6Q_PAD_KEY_COL2__GPIO4_IO10 0x80000000 /* user2 led */
370 MX6Q_PAD_KEY_ROW4__GPIO4_IO15 0x80000000 /* user3 led */
371 MX6Q_PAD_SD1_DAT0__GPIO1_IO16 0x80000000 /* USBHUB_RST# */
372 MX6Q_PAD_SD1_DAT3__GPIO1_IO21 0x80000000 /* MIPI_DIO */
381 crtcs = <&ipu1 0>, <&ipu1 1>, <&ipu2 0>, <&ipu2 1>;
386 reset-gpio = <&gpio1 29 0>;
389 eth1: sky2@8 { /* MAC/PHY on bus 8 */
390 compatible = "marvell,sky2";
391 /* Filled in by U-Boot */
392 mac-address = [ 00 00 00 00 00 00 ];
397 fsl,mode = "i2s-slave";
402 pinctrl-names = "default";
403 pinctrl-0 = <&pinctrl_uart1_2>;
408 pinctrl-names = "default";
409 pinctrl-0 = <&pinctrl_uart2_2>;
414 pinctrl-names = "default";
415 pinctrl-0 = <&pinctrl_uart3_1>;
420 pinctrl-names = "default";
421 pinctrl-0 = <&pinctrl_uart5_1>;
426 vbus-supply = <®_usb_otg_vbus>;
427 pinctrl-names = "default";
428 pinctrl-0 = <&pinctrl_usbotg_1>;
429 disable-over-current;
434 vbus-supply = <®_usb_h1_vbus>;
439 pinctrl-names = "default";
440 pinctrl-0 = <&pinctrl_usdhc3_2>;
441 cd-gpios = <&gpio7 0 0>;
442 vmmc-supply = <®_3p3v>;