target/linux/brcm2708/patches-4.9/0045-lirc-added-support-for-RaspberryPi-GPIO.patch

   1 From 277c109833c1d78543bec0723ab42f4c79937df9 Mon Sep 17 00:00:00 2001
   2 From: Aron Szabo <aron@aron.ws>
   3 Date: Sat, 16 Jun 2012 12:15:55 +0200
   4 Subject: [PATCH] lirc: added support for RaspberryPi GPIO
   5
   6 lirc_rpi: Use read_current_timer to determine transmitter delay. Thanks to jjmz and others
   7 See: https://github.com/raspberrypi/linux/issues/525
   8
   9 lirc: Remove restriction on gpio pins that can be used with lirc
  10
  11 Compute Module, for example could use different pins
  12
  13 lirc_rpi: Add parameter to specify input pin pull
  14
  15 Depending on the connected IR circuitry it might be desirable to change the
  16 gpios internal pull from it pull-down default behaviour. Add a module
  17 parameter to allow the user to set it explicitly.
  18
  19 Signed-off-by: Julian Scheel <julian@jusst.de>
  20
  21 lirc-rpi: Use the higher-level irq control functions
  22
  23 This module used to access the irq_chip methods of the
  24 gpio controller directly, rather than going through the
  25 standard enable_irq/irq_set_irq_type functions. This
  26 caused problems on pinctrl-bcm2835 which only implements
  27 the irq_enable/disable methods and not irq_unmask/mask.
  28
  29 lirc-rpi: Correct the interrupt usage
  30
  31 1) Correct the use of enable_irq (i.e. don't call it so often)
  32 2) Correct the shutdown sequence.
  33 3) Avoid a bcm2708_gpio driver quirk by setting the irq flags earlier
  34
  35 lirc-rpi: use getnstimeofday instead of read_current_timer
  36
  37 read_current_timer isn't guaranteed to return values in
  38 microseconds, and indeed it doesn't on a Pi2.
  39
  40 Issue: linux#827
  41
  42 lirc-rpi: Add device tree support, and a suitable overlay
  43
  44 The overlay supports DT parameters that match the old module
  45 parameters, except that gpio_in_pull should be set using the
  46 strings "up", "down" or "off".
  47
  48 lirc-rpi: Also support pinctrl-bcm2835 in non-DT mode
  49
  50 fix auto-sense in lirc_rpi driver
  51
  52 On a Raspberry Pi 2, the lirc_rpi driver might receive spurious
  53 interrupts and change it's low-active / high-active setting.
  54 When this happens, the IR remote control stops working.
  55
  56 This patch disables this auto-detection if the 'sense' parameter
  57 was set in the device tree, making the driver robust to such
  58 spurious interrupts.
  59 ---
  60  drivers/staging/media/lirc/Kconfig    |   6 +
  61  drivers/staging/media/lirc/Makefile   |   1 +
  62  drivers/staging/media/lirc/lirc_rpi.c | 734 ++++++++++++++++++++++++++++++++++
  63  include/linux/platform_data/bcm2708.h |  23 ++
  64  4 files changed, 764 insertions(+)
  65  create mode 100644 drivers/staging/media/lirc/lirc_rpi.c
  66  create mode 100644 include/linux/platform_data/bcm2708.h
  67
  68 --- a/drivers/staging/media/lirc/Kconfig
  69 +++ b/drivers/staging/media/lirc/Kconfig
  70 @@ -32,6 +32,12 @@ config LIRC_PARALLEL
  71         help
  72           Driver for Homebrew Parallel Port Receivers
  73
  74 +config LIRC_RPI
  75 +       tristate "Homebrew GPIO Port Receiver/Transmitter for the RaspberryPi"
  76 +       depends on LIRC
  77 +       help
  78 +         Driver for Homebrew GPIO Port Receiver/Transmitter for the RaspberryPi
  79 +
  80  config LIRC_SASEM
  81         tristate "Sasem USB IR Remote"
  82         depends on LIRC && USB
  83 --- a/drivers/staging/media/lirc/Makefile
  84 +++ b/drivers/staging/media/lirc/Makefile
  85 @@ -6,6 +6,7 @@
  86  obj-$(CONFIG_LIRC_BT829)       += lirc_bt829.o
  87  obj-$(CONFIG_LIRC_IMON)                += lirc_imon.o
  88  obj-$(CONFIG_LIRC_PARALLEL)    += lirc_parallel.o
  89 +obj-$(CONFIG_LIRC_RPI)         += lirc_rpi.o
  90  obj-$(CONFIG_LIRC_SASEM)       += lirc_sasem.o
  91  obj-$(CONFIG_LIRC_SERIAL)      += lirc_serial.o
  92  obj-$(CONFIG_LIRC_SIR)         += lirc_sir.o
  93 --- /dev/null
  94 +++ b/drivers/staging/media/lirc/lirc_rpi.c
  95 @@ -0,0 +1,734 @@
  96 +/*
  97 + * lirc_rpi.c
  98 + *
  99 + * lirc_rpi - Device driver that records pulse- and pause-lengths
 100 + *           (space-lengths) (just like the lirc_serial driver does)
 101 + *           between GPIO interrupt events on the Raspberry Pi.
 102 + *           Lots of code has been taken from the lirc_serial module,
 103 + *           so I would like say thanks to the authors.
 104 + *
 105 + * Copyright (C) 2012 Aron Robert Szabo <aron@reon.hu>,
 106 + *                   Michael Bishop <cleverca22@gmail.com>
 107 + *  This program is free software; you can redistribute it and/or modify
 108 + *  it under the terms of the GNU General Public License as published by
 109 + *  the Free Software Foundation; either version 2 of the License, or
 110 + *  (at your option) any later version.
 111 + *
 112 + *  This program is distributed in the hope that it will be useful,
 113 + *  but WITHOUT ANY WARRANTY; without even the implied warranty of
 114 + *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 115 + *  GNU General Public License for more details.
 116 + *
 117 + *  You should have received a copy of the GNU General Public License
 118 + *  along with this program; if not, write to the Free Software
 119 + *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 120 + */
 121 +
 122 +#include <linux/module.h>
 123 +#include <linux/errno.h>
 124 +#include <linux/interrupt.h>
 125 +#include <linux/sched.h>
 126 +#include <linux/kernel.h>
 127 +#include <linux/time.h>
 128 +#include <linux/timex.h>
 129 +#include <linux/timekeeping.h>
 130 +#include <linux/string.h>
 131 +#include <linux/delay.h>
 132 +#include <linux/platform_device.h>
 133 +#include <linux/irq.h>
 134 +#include <linux/spinlock.h>
 135 +#include <media/lirc.h>
 136 +#include <media/lirc_dev.h>
 137 +#include <linux/gpio.h>
 138 +#include <linux/of_platform.h>
 139 +#include <linux/platform_data/bcm2708.h>
 140 +
 141 +#define LIRC_DRIVER_NAME "lirc_rpi"
 142 +#define RBUF_LEN 256
 143 +#define LIRC_TRANSMITTER_LATENCY 50
 144 +
 145 +#ifndef MAX_UDELAY_MS
 146 +#define MAX_UDELAY_US 5000
 147 +#else
 148 +#define MAX_UDELAY_US (MAX_UDELAY_MS*1000)
 149 +#endif
 150 +
 151 +#define dprintk(fmt, args...)                                  \
 152 +       do {                                                    \
 153 +               if (debug)                                      \
 154 +                       printk(KERN_DEBUG LIRC_DRIVER_NAME ": " \
 155 +                              fmt, ## args);                   \
 156 +       } while (0)
 157 +
 158 +/* module parameters */
 159 +
 160 +/* set the default GPIO input pin */
 161 +static int gpio_in_pin = 18;
 162 +/* set the default pull behaviour for input pin */
 163 +static int gpio_in_pull = BCM2708_PULL_DOWN;
 164 +/* set the default GPIO output pin */
 165 +static int gpio_out_pin = 17;
 166 +/* enable debugging messages */
 167 +static bool debug;
 168 +/* -1 = auto, 0 = active high, 1 = active low */
 169 +static int sense = -1;
 170 +/* use softcarrier by default */
 171 +static bool softcarrier = 1;
 172 +/* 0 = do not invert output, 1 = invert output */
 173 +static bool invert = 0;
 174 +
 175 +struct gpio_chip *gpiochip;
 176 +static int irq_num;
 177 +static int auto_sense = 1;
 178 +
 179 +/* forward declarations */
 180 +static long send_pulse(unsigned long length);
 181 +static void send_space(long length);
 182 +static void lirc_rpi_exit(void);
 183 +
 184 +static struct platform_device *lirc_rpi_dev;
 185 +static struct timeval lasttv = { 0, 0 };
 186 +static struct lirc_buffer rbuf;
 187 +static spinlock_t lock;
 188 +
 189 +/* initialized/set in init_timing_params() */
 190 +static unsigned int freq = 38000;
 191 +static unsigned int duty_cycle = 50;
 192 +static unsigned long period;
 193 +static unsigned long pulse_width;
 194 +static unsigned long space_width;
 195 +
 196 +static void safe_udelay(unsigned long usecs)
 197 +{
 198 +       while (usecs > MAX_UDELAY_US) {
 199 +               udelay(MAX_UDELAY_US);
 200 +               usecs -= MAX_UDELAY_US;
 201 +       }
 202 +       udelay(usecs);
 203 +}
 204 +
 205 +static unsigned long read_current_us(void)
 206 +{
 207 +       struct timespec now;
 208 +       getnstimeofday(&now);
 209 +       return (now.tv_sec * 1000000) + (now.tv_nsec/1000);
 210 +}
 211 +
 212 +static int init_timing_params(unsigned int new_duty_cycle,
 213 +       unsigned int new_freq)
 214 +{
 215 +       if (1000 * 1000000L / new_freq * new_duty_cycle / 100 <=
 216 +           LIRC_TRANSMITTER_LATENCY)
 217 +               return -EINVAL;
 218 +       if (1000 * 1000000L / new_freq * (100 - new_duty_cycle) / 100 <=
 219 +           LIRC_TRANSMITTER_LATENCY)
 220 +               return -EINVAL;
 221 +       duty_cycle = new_duty_cycle;
 222 +       freq = new_freq;
 223 +       period = 1000 * 1000000L / freq;
 224 +       pulse_width = period * duty_cycle / 100;
 225 +       space_width = period - pulse_width;
 226 +       dprintk("in init_timing_params, freq=%d pulse=%ld, "
 227 +               "space=%ld\n", freq, pulse_width, space_width);
 228 +       return 0;
 229 +}
 230 +
 231 +static long send_pulse_softcarrier(unsigned long length)
 232 +{
 233 +       int flag;
 234 +       unsigned long actual, target;
 235 +       unsigned long actual_us, initial_us, target_us;
 236 +
 237 +       length *= 1000;
 238 +
 239 +       actual = 0; target = 0; flag = 0;
 240 +       actual_us = read_current_us();
 241 +
 242 +       while (actual < length) {
 243 +               if (flag) {
 244 +                       gpiochip->set(gpiochip, gpio_out_pin, invert);
 245 +                       target += space_width;
 246 +               } else {
 247 +                       gpiochip->set(gpiochip, gpio_out_pin, !invert);
 248 +                       target += pulse_width;
 249 +               }
 250 +               initial_us = actual_us;
 251 +               target_us = actual_us + (target - actual) / 1000;
 252 +               /*
 253 +                * Note - we've checked in ioctl that the pulse/space
 254 +                * widths are big enough so that d is > 0
 255 +                */
 256 +               if  ((int)(target_us - actual_us) > 0)
 257 +                       udelay(target_us - actual_us);
 258 +               actual_us = read_current_us();
 259 +               actual += (actual_us - initial_us) * 1000;
 260 +               flag = !flag;
 261 +       }
 262 +       return (actual-length) / 1000;
 263 +}
 264 +
 265 +static long send_pulse(unsigned long length)
 266 +{
 267 +       if (length <= 0)
 268 +               return 0;
 269 +
 270 +       if (softcarrier) {
 271 +               return send_pulse_softcarrier(length);
 272 +       } else {
 273 +               gpiochip->set(gpiochip, gpio_out_pin, !invert);
 274 +               safe_udelay(length);
 275 +               return 0;
 276 +       }
 277 +}
 278 +
 279 +static void send_space(long length)
 280 +{
 281 +       gpiochip->set(gpiochip, gpio_out_pin, invert);
 282 +       if (length <= 0)
 283 +               return;
 284 +       safe_udelay(length);
 285 +}
 286 +
 287 +static void rbwrite(int l)
 288 +{
 289 +       if (lirc_buffer_full(&rbuf)) {
 290 +               /* no new signals will be accepted */
 291 +               dprintk("Buffer overrun\n");
 292 +               return;
 293 +       }
 294 +       lirc_buffer_write(&rbuf, (void *)&l);
 295 +}
 296 +
 297 +static void frbwrite(int l)
 298 +{
 299 +       /* simple noise filter */
 300 +       static int pulse, space;
 301 +       static unsigned int ptr;
 302 +
 303 +       if (ptr > 0 && (l & PULSE_BIT)) {
 304 +               pulse += l & PULSE_MASK;
 305 +               if (pulse > 250) {
 306 +                       rbwrite(space);
 307 +                       rbwrite(pulse | PULSE_BIT);
 308 +                       ptr = 0;
 309 +                       pulse = 0;
 310 +               }
 311 +               return;
 312 +       }
 313 +       if (!(l & PULSE_BIT)) {
 314 +               if (ptr == 0) {
 315 +                       if (l > 20000) {
 316 +                               space = l;
 317 +                               ptr++;
 318 +                               return;
 319 +                       }
 320 +               } else {
 321 +                       if (l > 20000) {
 322 +                               space += pulse;
 323 +                               if (space > PULSE_MASK)
 324 +                                       space = PULSE_MASK;
 325 +                               space += l;
 326 +                               if (space > PULSE_MASK)
 327 +                                       space = PULSE_MASK;
 328 +                               pulse = 0;
 329 +                               return;
 330 +                       }
 331 +                       rbwrite(space);
 332 +                       rbwrite(pulse | PULSE_BIT);
 333 +                       ptr = 0;
 334 +                       pulse = 0;
 335 +               }
 336 +       }
 337 +       rbwrite(l);
 338 +}
 339 +
 340 +static irqreturn_t irq_handler(int i, void *blah, struct pt_regs *regs)
 341 +{
 342 +       struct timeval tv;
 343 +       long deltv;
 344 +       int data;
 345 +       int signal;
 346 +
 347 +       /* use the GPIO signal level */
 348 +       signal = gpiochip->get(gpiochip, gpio_in_pin);
 349 +
 350 +       if (sense != -1) {
 351 +               /* get current time */
 352 +               do_gettimeofday(&tv);
 353 +
 354 +               /* calc time since last interrupt in microseconds */
 355 +               deltv = tv.tv_sec-lasttv.tv_sec;
 356 +               if (tv.tv_sec < lasttv.tv_sec ||
 357 +                   (tv.tv_sec == lasttv.tv_sec &&
 358 +                    tv.tv_usec < lasttv.tv_usec)) {
 359 +                       printk(KERN_WARNING LIRC_DRIVER_NAME
 360 +                              ": AIEEEE: your clock just jumped backwards\n");
 361 +                       printk(KERN_WARNING LIRC_DRIVER_NAME
 362 +                              ": %d %d %lx %lx %lx %lx\n", signal, sense,
 363 +                              tv.tv_sec, lasttv.tv_sec,
 364 +                              tv.tv_usec, lasttv.tv_usec);
 365 +                       data = PULSE_MASK;
 366 +               } else if (deltv > 15) {
 367 +                       data = PULSE_MASK; /* really long time */
 368 +                       if (!(signal^sense)) {
 369 +                               /* sanity check */
 370 +                               printk(KERN_DEBUG LIRC_DRIVER_NAME
 371 +                                      ": AIEEEE: %d %d %lx %lx %lx %lx\n",
 372 +                                      signal, sense, tv.tv_sec, lasttv.tv_sec,
 373 +                                      tv.tv_usec, lasttv.tv_usec);
 374 +                               /*
 375 +                                * detecting pulse while this
 376 +                                * MUST be a space!
 377 +                                */
 378 +                               if (auto_sense) {
 379 +                                       sense = sense ? 0 : 1;
 380 +                               }
 381 +                       }
 382 +               } else {
 383 +                       data = (int) (deltv*1000000 +
 384 +                                     (tv.tv_usec - lasttv.tv_usec));
 385 +               }
 386 +               frbwrite(signal^sense ? data : (data|PULSE_BIT));
 387 +               lasttv = tv;
 388 +               wake_up_interruptible(&rbuf.wait_poll);
 389 +       }
 390 +
 391 +       return IRQ_HANDLED;
 392 +}
 393 +
 394 +static int is_right_chip(struct gpio_chip *chip, void *data)
 395 +{
 396 +       dprintk("is_right_chip %s %d\n", chip->label, strcmp(data, chip->label));
 397 +
 398 +       if (strcmp(data, chip->label) == 0)
 399 +               return 1;
 400 +       return 0;
 401 +}
 402 +
 403 +static inline int read_bool_property(const struct device_node *np,
 404 +                                    const char *propname,
 405 +                                    bool *out_value)
 406 +{
 407 +       u32 value = 0;
 408 +       int err = of_property_read_u32(np, propname, &value);
 409 +       if (err == 0)
 410 +               *out_value = (value != 0);
 411 +       return err;
 412 +}
 413 +
 414 +static void read_pin_settings(struct device_node *node)
 415 +{
 416 +       u32 pin;
 417 +       int index;
 418 +
 419 +       for (index = 0;
 420 +            of_property_read_u32_index(
 421 +                    node,
 422 +                    "brcm,pins",
 423 +                    index,
 424 +                    &pin) == 0;
 425 +            index++) {
 426 +               u32 function;
 427 +               int err;
 428 +               err = of_property_read_u32_index(
 429 +                       node,
 430 +                       "brcm,function",
 431 +                       index,
 432 +                       &function);
 433 +               if (err == 0) {
 434 +                       if (function == 1) /* Output */
 435 +                               gpio_out_pin = pin;
 436 +                       else if (function == 0) /* Input */
 437 +                               gpio_in_pin = pin;
 438 +               }
 439 +       }
 440 +}
 441 +
 442 +static int init_port(void)
 443 +{
 444 +       int i, nlow, nhigh;
 445 +       struct device_node *node;
 446 +
 447 +       node = lirc_rpi_dev->dev.of_node;
 448 +
 449 +       gpiochip = gpiochip_find("bcm2708_gpio", is_right_chip);
 450 +
 451 +       /*
 452 +        * Because of the lack of a setpull function, only support
 453 +        * pinctrl-bcm2835 if using device tree.
 454 +       */
 455 +       if (!gpiochip && node)
 456 +               gpiochip = gpiochip_find("pinctrl-bcm2835", is_right_chip);
 457 +
 458 +       if (!gpiochip) {
 459 +               pr_err(LIRC_DRIVER_NAME ": gpio chip not found!\n");
 460 +               return -ENODEV;
 461 +       }
 462 +
 463 +       if (node) {
 464 +               struct device_node *pins_node;
 465 +
 466 +               pins_node = of_parse_phandle(node, "pinctrl-0", 0);
 467 +               if (!pins_node) {
 468 +                       printk(KERN_ERR LIRC_DRIVER_NAME
 469 +                              ": pinctrl settings not found!\n");
 470 +                       return -EINVAL;
 471 +               }
 472 +
 473 +               read_pin_settings(pins_node);
 474 +
 475 +               of_property_read_u32(node, "rpi,sense", &sense);
 476 +
 477 +               read_bool_property(node, "rpi,softcarrier", &softcarrier);
 478 +
 479 +               read_bool_property(node, "rpi,invert", &invert);
 480 +
 481 +               read_bool_property(node, "rpi,debug", &debug);
 482 +
 483 +       } else {
 484 +               return -EINVAL;
 485 +       }
 486 +
 487 +       gpiochip->set(gpiochip, gpio_out_pin, invert);
 488 +
 489 +       irq_num = gpiochip->to_irq(gpiochip, gpio_in_pin);
 490 +       dprintk("to_irq %d\n", irq_num);
 491 +
 492 +       /* if pin is high, then this must be an active low receiver. */
 493 +       if (sense == -1) {
 494 +               /* wait 1/2 sec for the power supply */
 495 +               msleep(500);
 496 +
 497 +               /*
 498 +                * probe 9 times every 0.04s, collect "votes" for
 499 +                * active high/low
 500 +                */
 501 +               nlow = 0;
 502 +               nhigh = 0;
 503 +               for (i = 0; i < 9; i++) {
 504 +                       if (gpiochip->get(gpiochip, gpio_in_pin))
 505 +                               nlow++;
 506 +                       else
 507 +                               nhigh++;
 508 +                       msleep(40);
 509 +               }
 510 +               sense = (nlow >= nhigh ? 1 : 0);
 511 +               printk(KERN_INFO LIRC_DRIVER_NAME
 512 +                      ": auto-detected active %s receiver on GPIO pin %d\n",
 513 +                      sense ? "low" : "high", gpio_in_pin);
 514 +       } else {
 515 +               printk(KERN_INFO LIRC_DRIVER_NAME
 516 +                      ": manually using active %s receiver on GPIO pin %d\n",
 517 +                      sense ? "low" : "high", gpio_in_pin);
 518 +               auto_sense = 0;
 519 +       }
 520 +
 521 +       return 0;
 522 +}
 523 +
 524 +// called when the character device is opened
 525 +static int set_use_inc(void *data)
 526 +{
 527 +       int result;
 528 +
 529 +       /* initialize timestamp */
 530 +       do_gettimeofday(&lasttv);
 531 +
 532 +       result = request_irq(irq_num,
 533 +                            (irq_handler_t) irq_handler,
 534 +                            IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING,
 535 +                            LIRC_DRIVER_NAME, (void*) 0);
 536 +
 537 +       switch (result) {
 538 +       case -EBUSY:
 539 +               printk(KERN_ERR LIRC_DRIVER_NAME
 540 +                      ": IRQ %d is busy\n",
 541 +                      irq_num);
 542 +               return -EBUSY;
 543 +       case -EINVAL:
 544 +               printk(KERN_ERR LIRC_DRIVER_NAME
 545 +                      ": Bad irq number or handler\n");
 546 +               return -EINVAL;
 547 +       default:
 548 +               dprintk("Interrupt %d obtained\n",
 549 +                       irq_num);
 550 +               break;
 551 +       };
 552 +
 553 +       /* initialize pulse/space widths */
 554 +       init_timing_params(duty_cycle, freq);
 555 +
 556 +       return 0;
 557 +}
 558 +
 559 +static void set_use_dec(void *data)
 560 +{
 561 +       /* GPIO Pin Falling/Rising Edge Detect Disable */
 562 +       irq_set_irq_type(irq_num, 0);
 563 +       disable_irq(irq_num);
 564 +
 565 +       free_irq(irq_num, (void *) 0);
 566 +
 567 +       dprintk(KERN_INFO LIRC_DRIVER_NAME
 568 +               ": freed IRQ %d\n", irq_num);
 569 +}
 570 +
 571 +static ssize_t lirc_write(struct file *file, const char *buf,
 572 +       size_t n, loff_t *ppos)
 573 +{
 574 +       int i, count;
 575 +       unsigned long flags;
 576 +       long delta = 0;
 577 +       int *wbuf;
 578 +
 579 +       count = n / sizeof(int);
 580 +       if (n % sizeof(int) || count % 2 == 0)
 581 +               return -EINVAL;
 582 +       wbuf = memdup_user(buf, n);
 583 +       if (IS_ERR(wbuf))
 584 +               return PTR_ERR(wbuf);
 585 +       spin_lock_irqsave(&lock, flags);
 586 +
 587 +       for (i = 0; i < count; i++) {
 588 +               if (i%2)
 589 +                       send_space(wbuf[i] - delta);
 590 +               else
 591 +                       delta = send_pulse(wbuf[i]);
 592 +       }
 593 +       gpiochip->set(gpiochip, gpio_out_pin, invert);
 594 +
 595 +       spin_unlock_irqrestore(&lock, flags);
 596 +       kfree(wbuf);
 597 +       return n;
 598 +}
 599 +
 600 +static long lirc_ioctl(struct file *filep, unsigned int cmd, unsigned long arg)
 601 +{
 602 +       int result;
 603 +       __u32 value;
 604 +
 605 +       switch (cmd) {
 606 +       case LIRC_GET_SEND_MODE:
 607 +               return -ENOIOCTLCMD;
 608 +               break;
 609 +
 610 +       case LIRC_SET_SEND_MODE:
 611 +               result = get_user(value, (__u32 *) arg);
 612 +               if (result)
 613 +                       return result;
 614 +               /* only LIRC_MODE_PULSE supported */
 615 +               if (value != LIRC_MODE_PULSE)
 616 +                       return -ENOSYS;
 617 +               break;
 618 +
 619 +       case LIRC_GET_LENGTH:
 620 +               return -ENOSYS;
 621 +               break;
 622 +
 623 +       case LIRC_SET_SEND_DUTY_CYCLE:
 624 +               dprintk("SET_SEND_DUTY_CYCLE\n");
 625 +               result = get_user(value, (__u32 *) arg);
 626 +               if (result)
 627 +                       return result;
 628 +               if (value <= 0 || value > 100)
 629 +                       return -EINVAL;
 630 +               return init_timing_params(value, freq);
 631 +               break;
 632 +
 633 +       case LIRC_SET_SEND_CARRIER:
 634 +               dprintk("SET_SEND_CARRIER\n");
 635 +               result = get_user(value, (__u32 *) arg);
 636 +               if (result)
 637 +                       return result;
 638 +               if (value > 500000 || value < 20000)
 639 +                       return -EINVAL;
 640 +               return init_timing_params(duty_cycle, value);
 641 +               break;
 642 +
 643 +       default:
 644 +               return lirc_dev_fop_ioctl(filep, cmd, arg);
 645 +       }
 646 +       return 0;
 647 +}
 648 +
 649 +static const struct file_operations lirc_fops = {
 650 +       .owner          = THIS_MODULE,
 651 +       .write          = lirc_write,
 652 +       .unlocked_ioctl = lirc_ioctl,
 653 +       .read           = lirc_dev_fop_read,
 654 +       .poll           = lirc_dev_fop_poll,
 655 +       .open           = lirc_dev_fop_open,
 656 +       .release        = lirc_dev_fop_close,
 657 +       .llseek         = no_llseek,
 658 +};
 659 +
 660 +static struct lirc_driver driver = {
 661 +       .name           = LIRC_DRIVER_NAME,
 662 +       .minor          = -1,
 663 +       .code_length    = 1,
 664 +       .sample_rate    = 0,
 665 +       .data           = NULL,
 666 +       .add_to_buf     = NULL,
 667 +       .rbuf           = &rbuf,
 668 +       .set_use_inc    = set_use_inc,
 669 +       .set_use_dec    = set_use_dec,
 670 +       .fops           = &lirc_fops,
 671 +       .dev            = NULL,
 672 +       .owner          = THIS_MODULE,
 673 +};
 674 +
 675 +static const struct of_device_id lirc_rpi_of_match[] = {
 676 +       { .compatible = "rpi,lirc-rpi", },
 677 +       {},
 678 +};
 679 +MODULE_DEVICE_TABLE(of, lirc_rpi_of_match);
 680 +
 681 +static struct platform_driver lirc_rpi_driver = {
 682 +       .driver = {
 683 +               .name   = LIRC_DRIVER_NAME,
 684 +               .owner  = THIS_MODULE,
 685 +               .of_match_table = of_match_ptr(lirc_rpi_of_match),
 686 +       },
 687 +};
 688 +
 689 +static int __init lirc_rpi_init(void)
 690 +{
 691 +       struct device_node *node;
 692 +       int result;
 693 +
 694 +       /* Init read buffer. */
 695 +       result = lirc_buffer_init(&rbuf, sizeof(int), RBUF_LEN);
 696 +       if (result < 0)
 697 +               return -ENOMEM;
 698 +
 699 +       result = platform_driver_register(&lirc_rpi_driver);
 700 +       if (result) {
 701 +               printk(KERN_ERR LIRC_DRIVER_NAME
 702 +                      ": lirc register returned %d\n", result);
 703 +               goto exit_buffer_free;
 704 +       }
 705 +
 706 +       node = of_find_compatible_node(NULL, NULL,
 707 +                                      lirc_rpi_of_match[0].compatible);
 708 +
 709 +       if (node) {
 710 +               /* DT-enabled */
 711 +               lirc_rpi_dev = of_find_device_by_node(node);
 712 +               WARN_ON(lirc_rpi_dev->dev.of_node != node);
 713 +               of_node_put(node);
 714 +       }
 715 +       else {
 716 +               lirc_rpi_dev = platform_device_alloc(LIRC_DRIVER_NAME, 0);
 717 +               if (!lirc_rpi_dev) {
 718 +                       result = -ENOMEM;
 719 +                       goto exit_driver_unregister;
 720 +               }
 721 +
 722 +               result = platform_device_add(lirc_rpi_dev);
 723 +               if (result)
 724 +                       goto exit_device_put;
 725 +       }
 726 +
 727 +       return 0;
 728 +
 729 +       exit_device_put:
 730 +       platform_device_put(lirc_rpi_dev);
 731 +
 732 +       exit_driver_unregister:
 733 +       platform_driver_unregister(&lirc_rpi_driver);
 734 +
 735 +       exit_buffer_free:
 736 +       lirc_buffer_free(&rbuf);
 737 +
 738 +       return result;
 739 +}
 740 +
 741 +static void lirc_rpi_exit(void)
 742 +{
 743 +       if (!lirc_rpi_dev->dev.of_node)
 744 +               platform_device_unregister(lirc_rpi_dev);
 745 +       platform_driver_unregister(&lirc_rpi_driver);
 746 +       lirc_buffer_free(&rbuf);
 747 +}
 748 +
 749 +static int __init lirc_rpi_init_module(void)
 750 +{
 751 +       int result;
 752 +
 753 +       result = lirc_rpi_init();
 754 +       if (result)
 755 +               return result;
 756 +
 757 +       result = init_port();
 758 +       if (result < 0)
 759 +               goto exit_rpi;
 760 +
 761 +       driver.features = LIRC_CAN_SET_SEND_DUTY_CYCLE |
 762 +                         LIRC_CAN_SET_SEND_CARRIER |
 763 +                         LIRC_CAN_SEND_PULSE |
 764 +                         LIRC_CAN_REC_MODE2;
 765 +
 766 +       driver.dev = &lirc_rpi_dev->dev;
 767 +       driver.minor = lirc_register_driver(&driver);
 768 +
 769 +       if (driver.minor < 0) {
 770 +               printk(KERN_ERR LIRC_DRIVER_NAME
 771 +                      ": device registration failed with %d\n", result);
 772 +               result = -EIO;
 773 +               goto exit_rpi;
 774 +       }
 775 +
 776 +       printk(KERN_INFO LIRC_DRIVER_NAME ": driver registered!\n");
 777 +
 778 +       return 0;
 779 +
 780 +       exit_rpi:
 781 +       lirc_rpi_exit();
 782 +
 783 +       return result;
 784 +}
 785 +
 786 +static void __exit lirc_rpi_exit_module(void)
 787 +{
 788 +       lirc_unregister_driver(driver.minor);
 789 +
 790 +       gpio_free(gpio_out_pin);
 791 +       gpio_free(gpio_in_pin);
 792 +
 793 +       lirc_rpi_exit();
 794 +
 795 +       printk(KERN_INFO LIRC_DRIVER_NAME ": cleaned up module\n");
 796 +}
 797 +
 798 +module_init(lirc_rpi_init_module);
 799 +module_exit(lirc_rpi_exit_module);
 800 +
 801 +MODULE_DESCRIPTION("Infra-red receiver and blaster driver for Raspberry Pi GPIO.");
 802 +MODULE_AUTHOR("Aron Robert Szabo <aron@reon.hu>");
 803 +MODULE_AUTHOR("Michael Bishop <cleverca22@gmail.com>");
 804 +MODULE_LICENSE("GPL");
 805 +
 806 +module_param(gpio_out_pin, int, S_IRUGO);
 807 +MODULE_PARM_DESC(gpio_out_pin, "GPIO output/transmitter pin number of the BCM"
 808 +                " processor. (default 17");
 809 +
 810 +module_param(gpio_in_pin, int, S_IRUGO);
 811 +MODULE_PARM_DESC(gpio_in_pin, "GPIO input pin number of the BCM processor."
 812 +                " (default 18");
 813 +
 814 +module_param(gpio_in_pull, int, S_IRUGO);
 815 +MODULE_PARM_DESC(gpio_in_pull, "GPIO input pin pull configuration."
 816 +                " (0 = off, 1 = up, 2 = down, default down)");
 817 +
 818 +module_param(sense, int, S_IRUGO);
 819 +MODULE_PARM_DESC(sense, "Override autodetection of IR receiver circuit"
 820 +                " (0 = active high, 1 = active low )");
 821 +
 822 +module_param(softcarrier, bool, S_IRUGO);
 823 +MODULE_PARM_DESC(softcarrier, "Software carrier (0 = off, 1 = on, default on)");
 824 +
 825 +module_param(invert, bool, S_IRUGO);
 826 +MODULE_PARM_DESC(invert, "Invert output (0 = off, 1 = on, default off");
 827 +
 828 +module_param(debug, bool, S_IRUGO | S_IWUSR);
 829 +MODULE_PARM_DESC(debug, "Enable debugging messages");
 830 --- /dev/null
 831 +++ b/include/linux/platform_data/bcm2708.h
 832 @@ -0,0 +1,23 @@
 833 +/*
 834 + * include/linux/platform_data/bcm2708.h
 835 + *
 836 + * This program is free software; you can redistribute it and/or modify
 837 + * it under the terms of the GNU General Public License version 2 as
 838 + * published by the Free Software Foundation.
 839 + *
 840 + * (C) 2014 Julian Scheel <julian@jusst.de>
 841 + *
 842 + */
 843 +#ifndef __BCM2708_H_
 844 +#define __BCM2708_H_
 845 +
 846 +typedef enum {
 847 +       BCM2708_PULL_OFF,
 848 +       BCM2708_PULL_UP,
 849 +       BCM2708_PULL_DOWN
 850 +} bcm2708_gpio_pull_t;
 851 +
 852 +extern int bcm2708_gpio_setpull(struct gpio_chip *gc, unsigned offset,
 853 +               bcm2708_gpio_pull_t value);
 854 +
 855 +#endif