target/linux/bcm63xx/patches-4.14/511-board_V2500V.patch

   1 --- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
   2 +++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
   3 @@ -435,6 +435,26 @@ static struct board_info __initdata boar
   4         .has_pccard                     = 1,
   5         .has_ehci0                      = 1,
   6  };
   7 +
   8 +static struct board_info __initdata board_V2500V_BB = {
   9 +       .name                           = "V2500V_BB",
  10 +        .expected_cpu_id                = 0x6348,
  11 +
  12 +        .has_enet0                      = 1,
  13 +        .has_enet1                      = 1,
  14 +        .has_pci                        = 1,
  15 +
  16 +        .enet0 = {
  17 +                .has_phy                = 1,
  18 +                .use_internal_phy       = 1,
  19 +        },
  20 +        .enet1 = {
  21 +               .has_phy                = 1,
  22 +               .phy_id                 = 0,
  23 +                .force_speed_100        = 1,
  24 +                .force_duplex_full      = 1,
  25 +       },
  26 +};
  27  #endif /* CONFIG_BCM63XX_CPU_6348 */
  28
  29  /*
  30 @@ -707,6 +727,7 @@ static const struct board_info __initcon
  31         &board_96348_D4PW,
  32         &board_spw500v,
  33         &board_96348sv,
  34 +       &board_V2500V_BB,
  35  #endif
  36
  37  #ifdef CONFIG_BCM63XX_CPU_6358
  38 @@ -746,6 +767,7 @@ static struct of_device_id const bcm963x
  39         { .compatible = "brcm,bcm96348gw-10", .data = &board_96348gw_10, },
  40         { .compatible = "brcm,bcm96348gw-11", .data = &board_96348gw_11, },
  41         { .compatible = "brcm,bcm96348gw-a", .data = &board_96348gw_a, },
  42 +       { .compatible = "bt,voyager-2500v-bb", .data = &board_V2500V_BB, },
  43         { .compatible = "d-link,dsl-2640b-b", .data = &board_96348_D4PW, },
  44         { .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, },
  45         { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, },
  46 @@ -805,6 +827,22 @@ void __init board_bcm963xx_init(void)
  47                 val &= MPI_CSBASE_BASE_MASK;
  48         }
  49         boot_addr = (u8 *)KSEG1ADDR(val);
  50 +       pr_info("Boot address 0x%08x\n",(unsigned int)boot_addr);
  51 +
  52 +       /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
  53 +       /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
  54 +       /* Loading firmware from the CFE Prompt always loads to Bank 0 */
  55 +       /* Do an early check of CFE and then select bank 0 */
  56 +
  57 +       if (boot_addr == (u8 *)0xbf800000) {
  58 +               u8 *tmp_boot_addr = (u8*)0xbfc00000;
  59 +
  60 +               bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
  61 +               if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
  62 +                       pr_info("V2500V: nvram bank 0\n");
  63 +                       boot_addr = tmp_boot_addr;
  64 +               }
  65 +       }
  66
  67         /* dump cfe version */
  68         cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
  69 --- a/arch/mips/bcm63xx/dev-flash.c
  70 +++ b/arch/mips/bcm63xx/dev-flash.c
  71 @@ -21,6 +21,7 @@
  72  #include <linux/spi/spi.h>
  73  #include <linux/spi/flash.h>
  74
  75 +#include <bcm63xx_board.h>
  76  #include <bcm63xx_cpu.h>
  77  #include <bcm63xx_dev_flash.h>
  78  #include <bcm63xx_regs.h>
  79 @@ -247,6 +248,13 @@ int __init bcm63xx_flash_register(void)
  80                         val = bcm_mpi_readl(MPI_CSBASE_REG(0));
  81                         val &= MPI_CSBASE_BASE_MASK;
  82
  83 +                       /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
  84 +                       /* Loading from CFE always uses Bank 0 */
  85 +                       if (!strcmp(board_get_name(), "V2500V_BB")) {
  86 +                               pr_info("V2500V: Start in Bank 0\n");
  87 +                               val = val + 0x400000; // Select Bank 0 start address
  88 +                       }
  89 +
  90                         mtd_resources[0].start = val;
  91                         mtd_resources[0].end = 0x1FFFFFFF;
  92                 }