1 --- a/drivers/net/ethernet/atheros/Makefile
2 +++ b/drivers/net/ethernet/atheros/Makefile
3 @@ -7,3 +7,4 @@ obj-$(CONFIG_ATL2) += atlx/
4 obj-$(CONFIG_ATL1E) += atl1e/
5 obj-$(CONFIG_ATL1C) += atl1c/
6 obj-$(CONFIG_ALX) += alx/
7 +obj-$(CONFIG_NET_AR231X) += ar231x/
8 --- a/drivers/net/ethernet/atheros/Kconfig
9 +++ b/drivers/net/ethernet/atheros/Kconfig
11 config NET_VENDOR_ATHEROS
12 bool "Atheros devices"
15 + depends on (PCI || ATHEROS_AR231X)
17 If you have a network (Ethernet) card belonging to this class, say Y
18 and read the Ethernet-HOWTO, available from
19 @@ -80,4 +80,10 @@ config ALX
20 To compile this driver as a module, choose M here. The module
24 + tristate "Atheros AR231X built-in Ethernet support"
25 + depends on ATHEROS_AR231X
27 + Support for the AR231x/531x ethernet controller
29 endif # NET_VENDOR_ATHEROS
31 +++ b/drivers/net/ethernet/atheros/ar231x/Makefile
33 +obj-$(CONFIG_NET_AR231X) += ar231x.o
35 +++ b/drivers/net/ethernet/atheros/ar231x/ar231x.c
38 + * ar231x.c: Linux driver for the Atheros AR231x Ethernet device.
40 + * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
41 + * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
42 + * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
44 + * Thanks to Atheros for providing hardware and documentation
45 + * enabling me to write this driver.
47 + * This program is free software; you can redistribute it and/or modify
48 + * it under the terms of the GNU General Public License as published by
49 + * the Free Software Foundation; either version 2 of the License, or
50 + * (at your option) any later version.
52 + * Additional credits:
53 + * This code is taken from John Taylor's Sibyte driver and then
54 + * modified for the AR2313.
57 +#include <linux/module.h>
58 +#include <linux/types.h>
59 +#include <linux/errno.h>
60 +#include <linux/ioport.h>
61 +#include <linux/netdevice.h>
62 +#include <linux/etherdevice.h>
63 +#include <linux/interrupt.h>
64 +#include <linux/skbuff.h>
65 +#include <linux/init.h>
66 +#include <linux/delay.h>
67 +#include <linux/mm.h>
68 +#include <linux/mii.h>
69 +#include <linux/phy.h>
70 +#include <linux/platform_device.h>
71 +#include <linux/io.h>
73 +#define AR2313_MTU 1692
74 +#define AR2313_PRIOS 1
75 +#define AR2313_QUEUES (2*AR2313_PRIOS)
76 +#define AR2313_DESCR_ENTRIES 64
79 +#define min(a, b) (((a) < (b)) ? (a) : (b))
82 +#ifndef SMP_CACHE_BYTES
83 +#define SMP_CACHE_BYTES L1_CACHE_BYTES
86 +#define AR2313_MBOX_SET_BIT 0x8
91 + * New interrupt handler strategy:
93 + * An old interrupt handler worked using the traditional method of
94 + * replacing an skbuff with a new one when a packet arrives. However
95 + * the rx rings do not need to contain a static number of buffer
96 + * descriptors, thus it makes sense to move the memory allocation out
97 + * of the main interrupt handler and do it in a bottom half handler
98 + * and only allocate new buffers when the number of buffers in the
99 + * ring is below a certain threshold. In order to avoid starving the
100 + * NIC under heavy load it is however necessary to force allocation
101 + * when hitting a minimum threshold. The strategy for alloction is as
104 + * RX_LOW_BUF_THRES - allocate buffers in the bottom half
105 + * RX_PANIC_LOW_THRES - we are very low on buffers, allocate
106 + * the buffers in the interrupt handler
107 + * RX_RING_THRES - maximum number of buffers in the rx ring
109 + * One advantagous side effect of this allocation approach is that the
110 + * entire rx processing can be done without holding any spin lock
111 + * since the rx rings and registers are totally independent of the tx
112 + * ring and its registers. This of course includes the kmalloc's of
113 + * new skb's. Thus start_xmit can run in parallel with rx processing
114 + * and the memory allocation on SMP systems.
116 + * Note that running the skb reallocation in a bottom half opens up
117 + * another can of races which needs to be handled properly. In
118 + * particular it can happen that the interrupt handler tries to run
119 + * the reallocation while the bottom half is either running on another
120 + * CPU or was interrupted on the same CPU. To get around this the
121 + * driver uses bitops to prevent the reallocation routines from being
124 + * TX handling can also be done without holding any spin lock, wheee
125 + * this is fun! since tx_csm is only written to by the interrupt
130 + * Threshold values for RX buffer allocation - the low water marks for
131 + * when to start refilling the rings are set to 75% of the ring
132 + * sizes. It seems to make sense to refill the rings entirely from the
133 + * intrrupt handler once it gets below the panic threshold, that way
134 + * we don't risk that the refilling is moved to another CPU when the
135 + * one running the interrupt handler just got the slab code hot in its
138 +#define RX_RING_SIZE AR2313_DESCR_ENTRIES
139 +#define RX_PANIC_THRES (RX_RING_SIZE/4)
140 +#define RX_LOW_THRES ((3*RX_RING_SIZE)/4)
144 +#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
150 +#define AR2313_BUFSIZE (AR2313_MTU + VLAN_HDR + ETH_HLEN + CRC_LEN + \
154 +MODULE_LICENSE("GPL");
155 +MODULE_AUTHOR("Sameer Dekate <sdekate@arubanetworks.com>, Imre Kaloz <kaloz@openwrt.org>, Felix Fietkau <nbd@openwrt.org>");
156 +MODULE_DESCRIPTION("AR231x Ethernet driver");
159 +#define virt_to_phys(x) ((u32)(x) & 0x1fffffff)
162 +static void ar231x_halt(struct net_device *dev);
163 +static void rx_tasklet_func(unsigned long data);
164 +static void rx_tasklet_cleanup(struct net_device *dev);
165 +static void ar231x_multicast_list(struct net_device *dev);
166 +static void ar231x_tx_timeout(struct net_device *dev);
168 +static int ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum);
169 +static int ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
171 +static int ar231x_mdiobus_reset(struct mii_bus *bus);
172 +static int ar231x_mdiobus_probe(struct net_device *dev);
173 +static void ar231x_adjust_link(struct net_device *dev);
176 +#define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
179 +#ifdef CONFIG_NET_POLL_CONTROLLER
181 +ar231x_netpoll(struct net_device *dev)
183 + unsigned long flags;
185 + local_irq_save(flags);
186 + ar231x_interrupt(dev->irq, dev);
187 + local_irq_restore(flags);
191 +static const struct net_device_ops ar231x_ops = {
192 + .ndo_open = ar231x_open,
193 + .ndo_stop = ar231x_close,
194 + .ndo_start_xmit = ar231x_start_xmit,
195 + .ndo_set_rx_mode = ar231x_multicast_list,
196 + .ndo_do_ioctl = ar231x_ioctl,
197 + .ndo_change_mtu = eth_change_mtu,
198 + .ndo_validate_addr = eth_validate_addr,
199 + .ndo_set_mac_address = eth_mac_addr,
200 + .ndo_tx_timeout = ar231x_tx_timeout,
201 +#ifdef CONFIG_NET_POLL_CONTROLLER
202 + .ndo_poll_controller = ar231x_netpoll,
206 +static int ar231x_probe(struct platform_device *pdev)
208 + struct net_device *dev;
209 + struct ar231x_private *sp;
210 + struct resource *res;
211 + unsigned long ar_eth_base;
214 + dev = alloc_etherdev(sizeof(struct ar231x_private));
218 + "ar231x: Unable to allocate net_device structure!\n");
222 + platform_set_drvdata(pdev, dev);
224 + sp = netdev_priv(dev);
226 + sp->cfg = pdev->dev.platform_data;
228 + sprintf(buf, "eth%d_membase", pdev->id);
229 + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, buf);
234 + ar_eth_base = res->start;
236 + sprintf(buf, "eth%d_irq", pdev->id);
237 + dev->irq = platform_get_irq_byname(pdev, buf);
239 + spin_lock_init(&sp->lock);
241 + dev->features |= NETIF_F_HIGHDMA;
242 + dev->netdev_ops = &ar231x_ops;
244 + tasklet_init(&sp->rx_tasklet, rx_tasklet_func, (unsigned long)dev);
245 + tasklet_disable(&sp->rx_tasklet);
247 + sp->eth_regs = ioremap_nocache(ar_eth_base, sizeof(*sp->eth_regs));
248 + if (!sp->eth_regs) {
249 + printk("Can't remap eth registers\n");
254 + * When there's only one MAC, PHY regs are typically on ENET0,
255 + * even though the MAC might be on ENET1.
256 + * So remap PHY regs separately.
258 + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "eth0_mii");
260 + res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
265 + sp->phy_regs = ioremap_nocache(res->start, resource_size(res));
266 + if (!sp->phy_regs) {
267 + printk("Can't remap phy registers\n");
271 + sp->dma_regs = ioremap_nocache(ar_eth_base + 0x1000,
272 + sizeof(*sp->dma_regs));
273 + if (!sp->dma_regs) {
274 + printk("Can't remap DMA registers\n");
277 + dev->base_addr = ar_eth_base + 0x1000;
279 + strncpy(sp->name, "Atheros AR231x", sizeof(sp->name) - 1);
280 + sp->name[sizeof(sp->name) - 1] = '\0';
281 + memcpy(dev->dev_addr, sp->cfg->macaddr, 6);
283 + if (ar231x_init(dev)) {
284 + /* ar231x_init() calls ar231x_init_cleanup() on error */
289 + if (register_netdev(dev)) {
290 + printk("%s: register_netdev failed\n", __func__);
294 + printk("%s: %s: %pM, irq %d\n", dev->name, sp->name, dev->dev_addr,
297 + sp->mii_bus = mdiobus_alloc();
298 + if (sp->mii_bus == NULL)
301 + sp->mii_bus->priv = dev;
302 + sp->mii_bus->read = ar231x_mdiobus_read;
303 + sp->mii_bus->write = ar231x_mdiobus_write;
304 + sp->mii_bus->reset = ar231x_mdiobus_reset;
305 + sp->mii_bus->name = "ar231x_eth_mii";
306 + snprintf(sp->mii_bus->id, MII_BUS_ID_SIZE, "%d", pdev->id);
307 + sp->mii_bus->irq = kmalloc(sizeof(int), GFP_KERNEL);
308 + *sp->mii_bus->irq = PHY_POLL;
310 + mdiobus_register(sp->mii_bus);
312 + if (ar231x_mdiobus_probe(dev) != 0) {
313 + printk(KERN_ERR "%s: mdiobus_probe failed\n", dev->name);
314 + rx_tasklet_cleanup(dev);
315 + ar231x_init_cleanup(dev);
316 + unregister_netdev(dev);
321 + /* start link poll timer */
322 + ar231x_setup_timer(dev);
327 +static void ar231x_multicast_list(struct net_device *dev)
329 + struct ar231x_private *sp = netdev_priv(dev);
330 + unsigned int filter;
332 + filter = sp->eth_regs->mac_control;
334 + if (dev->flags & IFF_PROMISC)
335 + filter |= MAC_CONTROL_PR;
337 + filter &= ~MAC_CONTROL_PR;
338 + if ((dev->flags & IFF_ALLMULTI) || (netdev_mc_count(dev) > 0))
339 + filter |= MAC_CONTROL_PM;
341 + filter &= ~MAC_CONTROL_PM;
343 + sp->eth_regs->mac_control = filter;
346 +static void rx_tasklet_cleanup(struct net_device *dev)
348 + struct ar231x_private *sp = netdev_priv(dev);
351 + * Tasklet may be scheduled. Need to get it removed from the list
352 + * since we're about to free the struct.
356 + tasklet_enable(&sp->rx_tasklet);
357 + tasklet_kill(&sp->rx_tasklet);
360 +static int ar231x_remove(struct platform_device *pdev)
362 + struct net_device *dev = platform_get_drvdata(pdev);
363 + struct ar231x_private *sp = netdev_priv(dev);
365 + rx_tasklet_cleanup(dev);
366 + ar231x_init_cleanup(dev);
367 + unregister_netdev(dev);
368 + mdiobus_unregister(sp->mii_bus);
369 + mdiobus_free(sp->mii_bus);
375 + * Restart the AR2313 ethernet controller.
377 +static int ar231x_restart(struct net_device *dev)
379 + /* disable interrupts */
380 + disable_irq(dev->irq);
388 + /* enable interrupts */
389 + enable_irq(dev->irq);
394 +static struct platform_driver ar231x_driver = {
395 + .driver.name = "ar231x-eth",
396 + .probe = ar231x_probe,
397 + .remove = ar231x_remove,
400 +module_platform_driver(ar231x_driver);
402 +static void ar231x_free_descriptors(struct net_device *dev)
404 + struct ar231x_private *sp = netdev_priv(dev);
406 + if (sp->rx_ring != NULL) {
407 + kfree((void *)KSEG0ADDR(sp->rx_ring));
408 + sp->rx_ring = NULL;
409 + sp->tx_ring = NULL;
413 +static int ar231x_allocate_descriptors(struct net_device *dev)
415 + struct ar231x_private *sp = netdev_priv(dev);
418 + ar231x_descr_t *space;
420 + if (sp->rx_ring != NULL) {
421 + printk("%s: already done.\n", __func__);
425 + size = sizeof(ar231x_descr_t) * (AR2313_DESCR_ENTRIES * AR2313_QUEUES);
426 + space = kmalloc(size, GFP_KERNEL);
430 + /* invalidate caches */
431 + dma_cache_inv((unsigned int)space, size);
433 + /* now convert pointer to KSEG1 */
434 + space = (ar231x_descr_t *)KSEG1ADDR(space);
436 + memset((void *)space, 0, size);
438 + sp->rx_ring = space;
439 + space += AR2313_DESCR_ENTRIES;
441 + sp->tx_ring = space;
442 + space += AR2313_DESCR_ENTRIES;
444 + /* Initialize the transmit Descriptors */
445 + for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
446 + ar231x_descr_t *td = &sp->tx_ring[j];
449 + td->devcs = DMA_TX1_CHAINED;
451 + td->descr = virt_to_phys(&sp->tx_ring[DSC_NEXT(j)]);
458 + * Generic cleanup handling data allocated during init. Used when the
459 + * module is unloaded or if an error occurs during initialization
461 +static void ar231x_init_cleanup(struct net_device *dev)
463 + struct ar231x_private *sp = netdev_priv(dev);
464 + struct sk_buff *skb;
467 + ar231x_free_descriptors(dev);
470 + iounmap((void *)sp->eth_regs);
472 + iounmap((void *)sp->dma_regs);
474 + iounmap((void *)sp->phy_regs);
477 + for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
478 + skb = sp->rx_skb[j];
480 + sp->rx_skb[j] = NULL;
481 + dev_kfree_skb(skb);
489 + for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
490 + skb = sp->tx_skb[j];
492 + sp->tx_skb[j] = NULL;
493 + dev_kfree_skb(skb);
501 +static int ar231x_setup_timer(struct net_device *dev)
503 + struct ar231x_private *sp = netdev_priv(dev);
505 + init_timer(&sp->link_timer);
507 + sp->link_timer.function = ar231x_link_timer_fn;
508 + sp->link_timer.data = (int)dev;
509 + sp->link_timer.expires = jiffies + HZ;
511 + add_timer(&sp->link_timer);
515 +static void ar231x_link_timer_fn(unsigned long data)
517 + struct net_device *dev = (struct net_device *)data;
518 + struct ar231x_private *sp = netdev_priv(dev);
521 + * See if the link status changed.
522 + * This was needed to make sure we set the PHY to the
523 + * autonegotiated value of half or full duplex.
525 + ar231x_check_link(dev);
528 + * Loop faster when we don't have link.
529 + * This was needed to speed up the AP bootstrap time.
532 + mod_timer(&sp->link_timer, jiffies + HZ / 2);
534 + mod_timer(&sp->link_timer, jiffies + LINK_TIMER);
537 +static void ar231x_check_link(struct net_device *dev)
539 + struct ar231x_private *sp = netdev_priv(dev);
542 + phy_data = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_BMSR);
543 + if (sp->phy_data != phy_data) {
544 + if (phy_data & BMSR_LSTATUS) {
546 + * Link is present, ready link partner ability to
547 + * deterine duplexity.
553 + reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy,
555 + if (reg & BMCR_ANENABLE) {
556 + /* auto neg enabled */
557 + reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy,
559 + duplex = reg & (LPA_100FULL | LPA_10FULL) ?
562 + /* no auto neg, just read duplex config */
563 + duplex = (reg & BMCR_FULLDPLX) ? 1 : 0;
566 + printk(KERN_INFO "%s: Configuring MAC for %s duplex\n",
567 + dev->name, (duplex) ? "full" : "half");
571 + sp->eth_regs->mac_control =
572 + (sp->eth_regs->mac_control |
573 + MAC_CONTROL_F) & ~MAC_CONTROL_DRO;
576 + sp->eth_regs->mac_control =
577 + (sp->eth_regs->mac_control |
578 + MAC_CONTROL_DRO) & ~MAC_CONTROL_F;
584 + sp->phy_data = phy_data;
588 +static int ar231x_reset_reg(struct net_device *dev)
590 + struct ar231x_private *sp = netdev_priv(dev);
591 + unsigned int ethsal, ethsah;
592 + unsigned int flags;
594 + sp->cfg->reset_set(sp->cfg->reset_mac);
596 + sp->cfg->reset_clear(sp->cfg->reset_mac);
598 + sp->cfg->reset_set(sp->cfg->reset_phy);
600 + sp->cfg->reset_clear(sp->cfg->reset_phy);
603 + sp->dma_regs->bus_mode = (DMA_BUS_MODE_SWR);
605 + sp->dma_regs->bus_mode =
606 + ((32 << DMA_BUS_MODE_PBL_SHIFT) | DMA_BUS_MODE_BLE);
608 + /* enable interrupts */
609 + sp->dma_regs->intr_ena = DMA_STATUS_AIS | DMA_STATUS_NIS |
610 + DMA_STATUS_RI | DMA_STATUS_TI |
612 + sp->dma_regs->xmt_base = virt_to_phys(sp->tx_ring);
613 + sp->dma_regs->rcv_base = virt_to_phys(sp->rx_ring);
614 + sp->dma_regs->control =
615 + (DMA_CONTROL_SR | DMA_CONTROL_ST | DMA_CONTROL_SF);
617 + sp->eth_regs->flow_control = (FLOW_CONTROL_FCE);
618 + sp->eth_regs->vlan_tag = (0x8100);
620 + /* Enable Ethernet Interface */
621 + flags = (MAC_CONTROL_TE | /* transmit enable */
622 + MAC_CONTROL_PM | /* pass mcast */
623 + MAC_CONTROL_F | /* full duplex */
624 + MAC_CONTROL_HBD); /* heart beat disabled */
626 + if (dev->flags & IFF_PROMISC) { /* set promiscuous mode */
627 + flags |= MAC_CONTROL_PR;
629 + sp->eth_regs->mac_control = flags;
631 + /* Set all Ethernet station address registers to their initial values */
632 + ethsah = (((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
633 + (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF);
635 + ethsal = (((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
636 + (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
637 + (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
638 + (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF);
640 + sp->eth_regs->mac_addr[0] = ethsah;
641 + sp->eth_regs->mac_addr[1] = ethsal;
648 +static int ar231x_init(struct net_device *dev)
650 + struct ar231x_private *sp = netdev_priv(dev);
653 + /* Allocate descriptors */
654 + if (ar231x_allocate_descriptors(dev)) {
655 + printk("%s: %s: ar231x_allocate_descriptors failed\n",
656 + dev->name, __func__);
661 + /* Get the memory for the skb rings */
662 + if (sp->rx_skb == NULL) {
664 + kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
666 + if (!(sp->rx_skb)) {
667 + printk("%s: %s: rx_skb kmalloc failed\n",
668 + dev->name, __func__);
673 + memset(sp->rx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
675 + if (sp->tx_skb == NULL) {
677 + kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
679 + if (!(sp->tx_skb)) {
680 + printk("%s: %s: tx_skb kmalloc failed\n",
681 + dev->name, __func__);
686 + memset(sp->tx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
689 + * Set tx_csm before we start receiving interrupts, otherwise
690 + * the interrupt handler might think it is supposed to process
691 + * tx ints before we are up and running, which may cause a null
692 + * pointer access in the int handler.
699 + /* Zero the stats before starting the interface */
700 + memset(&dev->stats, 0, sizeof(dev->stats));
703 + * We load the ring here as there seem to be no way to tell the
704 + * firmware to wipe the ring without re-initializing it.
706 + ar231x_load_rx_ring(dev, RX_RING_SIZE);
708 + /* Init hardware */
709 + ar231x_reset_reg(dev);
712 + ecode = request_irq(dev->irq, &ar231x_interrupt, IRQF_DISABLED,
715 + printk(KERN_WARNING "%s: %s: Requested IRQ %d is busy\n",
716 + dev->name, __func__, dev->irq);
720 + tasklet_enable(&sp->rx_tasklet);
725 + ar231x_init_cleanup(dev);
730 + * Load the rx ring.
732 + * Loading rings is safe without holding the spin lock since this is
733 + * done only before the device is enabled, thus no interrupts are
734 + * generated and by the interrupt handler/tasklet handler.
736 +static void ar231x_load_rx_ring(struct net_device *dev, int nr_bufs)
738 + struct ar231x_private *sp = netdev_priv(dev);
741 + idx = sp->rx_skbprd;
743 + for (i = 0; i < nr_bufs; i++) {
744 + struct sk_buff *skb;
745 + ar231x_descr_t *rd;
747 + if (sp->rx_skb[idx])
750 + skb = netdev_alloc_skb_ip_align(dev, AR2313_BUFSIZE);
752 + printk("\n\n\n\n %s: No memory in system\n\n\n\n",
757 + /* Make sure IP header starts on a fresh cache line */
759 + sp->rx_skb[idx] = skb;
761 + rd = (ar231x_descr_t *)&sp->rx_ring[idx];
763 + /* initialize dma descriptor */
764 + rd->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
766 + rd->addr = virt_to_phys(skb->data);
767 + rd->descr = virt_to_phys(&sp->rx_ring[DSC_NEXT(idx)]);
768 + rd->status = DMA_RX_OWN;
770 + idx = DSC_NEXT(idx);
774 + sp->rx_skbprd = idx;
777 +#define AR2313_MAX_PKTS_PER_CALL 64
779 +static int ar231x_rx_int(struct net_device *dev)
781 + struct ar231x_private *sp = netdev_priv(dev);
782 + struct sk_buff *skb, *skb_new;
783 + ar231x_descr_t *rxdesc;
784 + unsigned int status;
791 + /* process at most the entire ring and then wait for another int */
793 + rxdesc = &sp->rx_ring[idx];
794 + status = rxdesc->status;
796 + if (status & DMA_RX_OWN) {
797 + /* SiByte owns descriptor or descr not yet filled in */
802 + if (++pkts > AR2313_MAX_PKTS_PER_CALL) {
807 + if ((status & DMA_RX_ERROR) && !(status & DMA_RX_LONG)) {
808 + dev->stats.rx_errors++;
809 + dev->stats.rx_dropped++;
811 + /* add statistics counters */
812 + if (status & DMA_RX_ERR_CRC)
813 + dev->stats.rx_crc_errors++;
814 + if (status & DMA_RX_ERR_COL)
815 + dev->stats.rx_over_errors++;
816 + if (status & DMA_RX_ERR_LENGTH)
817 + dev->stats.rx_length_errors++;
818 + if (status & DMA_RX_ERR_RUNT)
819 + dev->stats.rx_over_errors++;
820 + if (status & DMA_RX_ERR_DESC)
821 + dev->stats.rx_over_errors++;
824 + /* alloc new buffer. */
825 + skb_new = netdev_alloc_skb_ip_align(dev,
827 + if (skb_new != NULL) {
828 + skb = sp->rx_skb[idx];
830 + skb_put(skb, ((status >> DMA_RX_LEN_SHIFT) &
831 + 0x3fff) - CRC_LEN);
833 + dev->stats.rx_bytes += skb->len;
834 + skb->protocol = eth_type_trans(skb, dev);
835 + /* pass the packet to upper layers */
838 + skb_new->dev = dev;
839 + /* reset descriptor's curr_addr */
840 + rxdesc->addr = virt_to_phys(skb_new->data);
842 + dev->stats.rx_packets++;
843 + sp->rx_skb[idx] = skb_new;
845 + dev->stats.rx_dropped++;
849 + rxdesc->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
851 + rxdesc->status = DMA_RX_OWN;
853 + idx = DSC_NEXT(idx);
861 +static void ar231x_tx_int(struct net_device *dev)
863 + struct ar231x_private *sp = netdev_priv(dev);
865 + struct sk_buff *skb;
866 + ar231x_descr_t *txdesc;
867 + unsigned int status = 0;
871 + while (idx != sp->tx_prd) {
872 + txdesc = &sp->tx_ring[idx];
873 + status = txdesc->status;
875 + if (status & DMA_TX_OWN) {
876 + /* ar231x dma still owns descr */
879 + /* done with this descriptor */
880 + dma_unmap_single(NULL, txdesc->addr,
881 + txdesc->devcs & DMA_TX1_BSIZE_MASK,
883 + txdesc->status = 0;
885 + if (status & DMA_TX_ERROR) {
886 + dev->stats.tx_errors++;
887 + dev->stats.tx_dropped++;
888 + if (status & DMA_TX_ERR_UNDER)
889 + dev->stats.tx_fifo_errors++;
890 + if (status & DMA_TX_ERR_HB)
891 + dev->stats.tx_heartbeat_errors++;
892 + if (status & (DMA_TX_ERR_LOSS | DMA_TX_ERR_LINK))
893 + dev->stats.tx_carrier_errors++;
894 + if (status & (DMA_TX_ERR_LATE | DMA_TX_ERR_COL |
895 + DMA_TX_ERR_JABBER | DMA_TX_ERR_DEFER))
896 + dev->stats.tx_aborted_errors++;
899 + dev->stats.tx_packets++;
902 + skb = sp->tx_skb[idx];
903 + sp->tx_skb[idx] = NULL;
904 + idx = DSC_NEXT(idx);
905 + dev->stats.tx_bytes += skb->len;
906 + dev_kfree_skb_irq(skb);
912 +static void rx_tasklet_func(unsigned long data)
914 + struct net_device *dev = (struct net_device *)data;
915 + struct ar231x_private *sp = netdev_priv(dev);
920 + if (ar231x_rx_int(dev)) {
921 + tasklet_hi_schedule(&sp->rx_tasklet);
923 + unsigned long flags;
925 + spin_lock_irqsave(&sp->lock, flags);
926 + sp->dma_regs->intr_ena |= DMA_STATUS_RI;
927 + spin_unlock_irqrestore(&sp->lock, flags);
931 +static void rx_schedule(struct net_device *dev)
933 + struct ar231x_private *sp = netdev_priv(dev);
935 + sp->dma_regs->intr_ena &= ~DMA_STATUS_RI;
937 + tasklet_hi_schedule(&sp->rx_tasklet);
940 +static irqreturn_t ar231x_interrupt(int irq, void *dev_id)
942 + struct net_device *dev = (struct net_device *)dev_id;
943 + struct ar231x_private *sp = netdev_priv(dev);
944 + unsigned int status, enabled;
946 + /* clear interrupt */
947 + /* Don't clear RI bit if currently disabled */
948 + status = sp->dma_regs->status;
949 + enabled = sp->dma_regs->intr_ena;
950 + sp->dma_regs->status = status & enabled;
952 + if (status & DMA_STATUS_NIS) {
953 + /* normal status */
955 + * Don't schedule rx processing if interrupt
956 + * is already disabled.
958 + if (status & enabled & DMA_STATUS_RI) {
959 + /* receive interrupt */
962 + if (status & DMA_STATUS_TI) {
963 + /* transmit interrupt */
964 + ar231x_tx_int(dev);
968 + /* abnormal status */
969 + if (status & (DMA_STATUS_FBE | DMA_STATUS_TPS))
970 + ar231x_restart(dev);
972 + return IRQ_HANDLED;
975 +static int ar231x_open(struct net_device *dev)
977 + struct ar231x_private *sp = netdev_priv(dev);
978 + unsigned int ethsal, ethsah;
980 + /* reset the hardware, in case the MAC address changed */
981 + ethsah = (((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
982 + (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF);
984 + ethsal = (((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
985 + (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
986 + (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
987 + (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF);
989 + sp->eth_regs->mac_addr[0] = ethsah;
990 + sp->eth_regs->mac_addr[1] = ethsal;
995 + netif_start_queue(dev);
997 + sp->eth_regs->mac_control |= MAC_CONTROL_RE;
1002 +static void ar231x_tx_timeout(struct net_device *dev)
1004 + struct ar231x_private *sp = netdev_priv(dev);
1005 + unsigned long flags;
1007 + spin_lock_irqsave(&sp->lock, flags);
1008 + ar231x_restart(dev);
1009 + spin_unlock_irqrestore(&sp->lock, flags);
1012 +static void ar231x_halt(struct net_device *dev)
1014 + struct ar231x_private *sp = netdev_priv(dev);
1017 + tasklet_disable(&sp->rx_tasklet);
1019 + /* kill the MAC */
1020 + sp->eth_regs->mac_control &= ~(MAC_CONTROL_RE | /* disable Receives */
1021 + MAC_CONTROL_TE); /* disable Transmits */
1023 + sp->dma_regs->control = 0;
1024 + sp->dma_regs->bus_mode = DMA_BUS_MODE_SWR;
1026 + /* place phy and MAC in reset */
1027 + sp->cfg->reset_set(sp->cfg->reset_mac);
1028 + sp->cfg->reset_set(sp->cfg->reset_phy);
1030 + /* free buffers on tx ring */
1031 + for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
1032 + struct sk_buff *skb;
1033 + ar231x_descr_t *txdesc;
1035 + txdesc = &sp->tx_ring[j];
1036 + txdesc->descr = 0;
1038 + skb = sp->tx_skb[j];
1040 + dev_kfree_skb(skb);
1041 + sp->tx_skb[j] = NULL;
1047 + * close should do nothing. Here's why. It's called when
1048 + * 'ifconfig bond0 down' is run. If it calls free_irq then
1049 + * the irq is gone forever ! When bond0 is made 'up' again,
1050 + * the ar231x_open () does not call request_irq (). Worse,
1051 + * the call to ar231x_halt() generates a WDOG reset due to
1052 + * the write to reset register and the box reboots.
1053 + * Commenting this out is good since it allows the
1054 + * system to resume when bond0 is made up again.
1056 +static int ar231x_close(struct net_device *dev)
1059 + /* Disable interrupts */
1060 + disable_irq(dev->irq);
1063 + * Without (or before) releasing irq and stopping hardware, this
1064 + * is an absolute non-sense, by the way. It will be reset instantly
1065 + * by the first irq.
1067 + netif_stop_queue(dev);
1069 + /* stop the MAC and DMA engines */
1072 + /* release the interrupt */
1073 + free_irq(dev->irq, dev);
1079 +static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev)
1081 + struct ar231x_private *sp = netdev_priv(dev);
1082 + ar231x_descr_t *td;
1086 + td = &sp->tx_ring[idx];
1088 + if (td->status & DMA_TX_OWN) {
1089 + /* free skbuf and lie to the caller that we sent it out */
1090 + dev->stats.tx_dropped++;
1091 + dev_kfree_skb(skb);
1093 + /* restart transmitter in case locked */
1094 + sp->dma_regs->xmt_poll = 0;
1098 + /* Setup the transmit descriptor. */
1099 + td->devcs = ((skb->len << DMA_TX1_BSIZE_SHIFT) |
1100 + (DMA_TX1_LS | DMA_TX1_IC | DMA_TX1_CHAINED));
1101 + td->addr = dma_map_single(NULL, skb->data, skb->len, DMA_TO_DEVICE);
1102 + td->status = DMA_TX_OWN;
1104 + /* kick transmitter last */
1105 + sp->dma_regs->xmt_poll = 0;
1107 + sp->tx_skb[idx] = skb;
1108 + idx = DSC_NEXT(idx);
1114 +static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1116 + struct ar231x_private *sp = netdev_priv(dev);
1122 + return phy_mii_ioctl(sp->phy_dev, ifr, cmd);
1128 + return -EOPNOTSUPP;
1131 +static void ar231x_adjust_link(struct net_device *dev)
1133 + struct ar231x_private *sp = netdev_priv(dev);
1136 + if (!sp->phy_dev->link)
1139 + if (sp->phy_dev->duplex != sp->oldduplex) {
1140 + mc = readl(&sp->eth_regs->mac_control);
1141 + mc &= ~(MAC_CONTROL_F | MAC_CONTROL_DRO);
1142 + if (sp->phy_dev->duplex)
1143 + mc |= MAC_CONTROL_F;
1145 + mc |= MAC_CONTROL_DRO;
1146 + writel(mc, &sp->eth_regs->mac_control);
1147 + sp->oldduplex = sp->phy_dev->duplex;
1151 +#define MII_ADDR(phy, reg) \
1152 + ((reg << MII_ADDR_REG_SHIFT) | (phy << MII_ADDR_PHY_SHIFT))
1155 +ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
1157 + struct net_device *const dev = bus->priv;
1158 + struct ar231x_private *sp = netdev_priv(dev);
1159 + volatile MII *ethernet = sp->phy_regs;
1161 + ethernet->mii_addr = MII_ADDR(phy_addr, regnum);
1162 + while (ethernet->mii_addr & MII_ADDR_BUSY)
1164 + return ethernet->mii_data >> MII_DATA_SHIFT;
1168 +ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value)
1170 + struct net_device *const dev = bus->priv;
1171 + struct ar231x_private *sp = netdev_priv(dev);
1172 + volatile MII *ethernet = sp->phy_regs;
1174 + while (ethernet->mii_addr & MII_ADDR_BUSY)
1176 + ethernet->mii_data = value << MII_DATA_SHIFT;
1177 + ethernet->mii_addr = MII_ADDR(phy_addr, regnum) | MII_ADDR_WRITE;
1182 +static int ar231x_mdiobus_reset(struct mii_bus *bus)
1184 + struct net_device *const dev = bus->priv;
1186 + ar231x_reset_reg(dev);
1191 +static int ar231x_mdiobus_probe(struct net_device *dev)
1193 + struct ar231x_private *const sp = netdev_priv(dev);
1194 + struct phy_device *phydev = NULL;
1197 + /* find the first (lowest address) PHY on the current MAC's MII bus */
1198 + for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++)
1199 + if (sp->mii_bus->phy_map[phy_addr]) {
1200 + phydev = sp->mii_bus->phy_map[phy_addr];
1201 + sp->phy = phy_addr;
1202 + break; /* break out with first one found */
1206 + printk(KERN_ERR "ar231x: %s: no PHY found\n", dev->name);
1210 + /* now we are supposed to have a proper phydev, to attach to... */
1212 + BUG_ON(phydev->attached_dev);
1214 + phydev = phy_connect(dev, dev_name(&phydev->dev), &ar231x_adjust_link,
1215 + PHY_INTERFACE_MODE_MII);
1217 + if (IS_ERR(phydev)) {
1218 + printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
1219 + return PTR_ERR(phydev);
1222 + /* mask with MAC supported features */
1223 + phydev->supported &= (SUPPORTED_10baseT_Half
1224 + | SUPPORTED_10baseT_Full
1225 + | SUPPORTED_100baseT_Half
1226 + | SUPPORTED_100baseT_Full
1227 + | SUPPORTED_Autoneg
1228 + /* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */
1232 + phydev->advertising = phydev->supported;
1234 + sp->oldduplex = -1;
1235 + sp->phy_dev = phydev;
1237 + printk(KERN_INFO "%s: attached PHY driver [%s] (mii_bus:phy_addr=%s)\n",
1238 + dev->name, phydev->drv->name, dev_name(&phydev->dev));
1244 +++ b/drivers/net/ethernet/atheros/ar231x/ar231x.h
1247 + * ar231x.h: Linux driver for the Atheros AR231x Ethernet device.
1249 + * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
1250 + * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
1251 + * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
1253 + * Thanks to Atheros for providing hardware and documentation
1254 + * enabling me to write this driver.
1256 + * This program is free software; you can redistribute it and/or modify
1257 + * it under the terms of the GNU General Public License as published by
1258 + * the Free Software Foundation; either version 2 of the License, or
1259 + * (at your option) any later version.
1265 +#include <linux/interrupt.h>
1266 +#include <generated/autoconf.h>
1267 +#include <linux/bitops.h>
1268 +#include <ar231x_platform.h>
1270 +/* probe link timer - 5 secs */
1271 +#define LINK_TIMER (5*HZ)
1273 +#define IS_DMA_TX_INT(X) (((X) & (DMA_STATUS_TI)) != 0)
1274 +#define IS_DMA_RX_INT(X) (((X) & (DMA_STATUS_RI)) != 0)
1275 +#define IS_DRIVER_OWNED(X) (((X) & (DMA_TX_OWN)) == 0)
1277 +#define AR2313_TX_TIMEOUT (HZ/4)
1280 +#define DSC_RING_ENTRIES_SIZE (AR2313_DESCR_ENTRIES * sizeof(struct desc))
1281 +#define DSC_NEXT(idx) ((idx + 1) & (AR2313_DESCR_ENTRIES - 1))
1283 +#define AR2313_MBGET 2
1284 +#define AR2313_MBSET 3
1285 +#define AR2313_PCI_RECONFIG 4
1286 +#define AR2313_PCI_DUMP 5
1287 +#define AR2313_TEST_PANIC 6
1288 +#define AR2313_TEST_NULLPTR 7
1289 +#define AR2313_READ_DATA 8
1290 +#define AR2313_WRITE_DATA 9
1291 +#define AR2313_GET_VERSION 10
1292 +#define AR2313_TEST_HANG 11
1293 +#define AR2313_SYNC 12
1295 +#define DMA_RX_ERR_CRC BIT(1)
1296 +#define DMA_RX_ERR_DRIB BIT(2)
1297 +#define DMA_RX_ERR_MII BIT(3)
1298 +#define DMA_RX_EV2 BIT(5)
1299 +#define DMA_RX_ERR_COL BIT(6)
1300 +#define DMA_RX_LONG BIT(7)
1301 +#define DMA_RX_LS BIT(8) /* last descriptor */
1302 +#define DMA_RX_FS BIT(9) /* first descriptor */
1303 +#define DMA_RX_MF BIT(10) /* multicast frame */
1304 +#define DMA_RX_ERR_RUNT BIT(11) /* runt frame */
1305 +#define DMA_RX_ERR_LENGTH BIT(12) /* length error */
1306 +#define DMA_RX_ERR_DESC BIT(14) /* descriptor error */
1307 +#define DMA_RX_ERROR BIT(15) /* error summary */
1308 +#define DMA_RX_LEN_MASK 0x3fff0000
1309 +#define DMA_RX_LEN_SHIFT 16
1310 +#define DMA_RX_FILT BIT(30)
1311 +#define DMA_RX_OWN BIT(31) /* desc owned by DMA controller */
1313 +#define DMA_RX1_BSIZE_MASK 0x000007ff
1314 +#define DMA_RX1_BSIZE_SHIFT 0
1315 +#define DMA_RX1_CHAINED BIT(24)
1316 +#define DMA_RX1_RER BIT(25)
1318 +#define DMA_TX_ERR_UNDER BIT(1) /* underflow error */
1319 +#define DMA_TX_ERR_DEFER BIT(2) /* excessive deferral */
1320 +#define DMA_TX_COL_MASK 0x78
1321 +#define DMA_TX_COL_SHIFT 3
1322 +#define DMA_TX_ERR_HB BIT(7) /* hearbeat failure */
1323 +#define DMA_TX_ERR_COL BIT(8) /* excessive collisions */
1324 +#define DMA_TX_ERR_LATE BIT(9) /* late collision */
1325 +#define DMA_TX_ERR_LINK BIT(10) /* no carrier */
1326 +#define DMA_TX_ERR_LOSS BIT(11) /* loss of carrier */
1327 +#define DMA_TX_ERR_JABBER BIT(14) /* transmit jabber timeout */
1328 +#define DMA_TX_ERROR BIT(15) /* frame aborted */
1329 +#define DMA_TX_OWN BIT(31) /* descr owned by DMA controller */
1331 +#define DMA_TX1_BSIZE_MASK 0x000007ff
1332 +#define DMA_TX1_BSIZE_SHIFT 0
1333 +#define DMA_TX1_CHAINED BIT(24) /* chained descriptors */
1334 +#define DMA_TX1_TER BIT(25) /* transmit end of ring */
1335 +#define DMA_TX1_FS BIT(29) /* first segment */
1336 +#define DMA_TX1_LS BIT(30) /* last segment */
1337 +#define DMA_TX1_IC BIT(31) /* interrupt on completion */
1339 +#define RCVPKT_LENGTH(X) (X >> 16) /* Received pkt Length */
1341 +#define MAC_CONTROL_RE BIT(2) /* receive enable */
1342 +#define MAC_CONTROL_TE BIT(3) /* transmit enable */
1343 +#define MAC_CONTROL_DC BIT(5) /* Deferral check */
1344 +#define MAC_CONTROL_ASTP BIT(8) /* Auto pad strip */
1345 +#define MAC_CONTROL_DRTY BIT(10) /* Disable retry */
1346 +#define MAC_CONTROL_DBF BIT(11) /* Disable bcast frames */
1347 +#define MAC_CONTROL_LCC BIT(12) /* late collision ctrl */
1348 +#define MAC_CONTROL_HP BIT(13) /* Hash Perfect filtering */
1349 +#define MAC_CONTROL_HASH BIT(14) /* Unicast hash filtering */
1350 +#define MAC_CONTROL_HO BIT(15) /* Hash only filtering */
1351 +#define MAC_CONTROL_PB BIT(16) /* Pass Bad frames */
1352 +#define MAC_CONTROL_IF BIT(17) /* Inverse filtering */
1353 +#define MAC_CONTROL_PR BIT(18) /* promis mode (valid frames only) */
1354 +#define MAC_CONTROL_PM BIT(19) /* pass multicast */
1355 +#define MAC_CONTROL_F BIT(20) /* full-duplex */
1356 +#define MAC_CONTROL_DRO BIT(23) /* Disable Receive Own */
1357 +#define MAC_CONTROL_HBD BIT(28) /* heart-beat disabled (MUST BE SET) */
1358 +#define MAC_CONTROL_BLE BIT(30) /* big endian mode */
1359 +#define MAC_CONTROL_RA BIT(31) /* rcv all (valid and invalid frames) */
1361 +#define MII_ADDR_BUSY BIT(0)
1362 +#define MII_ADDR_WRITE BIT(1)
1363 +#define MII_ADDR_REG_SHIFT 6
1364 +#define MII_ADDR_PHY_SHIFT 11
1365 +#define MII_DATA_SHIFT 0
1367 +#define FLOW_CONTROL_FCE BIT(1)
1369 +#define DMA_BUS_MODE_SWR BIT(0) /* software reset */
1370 +#define DMA_BUS_MODE_BLE BIT(7) /* big endian mode */
1371 +#define DMA_BUS_MODE_PBL_SHIFT 8 /* programmable burst length 32 */
1372 +#define DMA_BUS_MODE_DBO BIT(20) /* big-endian descriptors */
1374 +#define DMA_STATUS_TI BIT(0) /* transmit interrupt */
1375 +#define DMA_STATUS_TPS BIT(1) /* transmit process stopped */
1376 +#define DMA_STATUS_TU BIT(2) /* transmit buffer unavailable */
1377 +#define DMA_STATUS_TJT BIT(3) /* transmit buffer timeout */
1378 +#define DMA_STATUS_UNF BIT(5) /* transmit underflow */
1379 +#define DMA_STATUS_RI BIT(6) /* receive interrupt */
1380 +#define DMA_STATUS_RU BIT(7) /* receive buffer unavailable */
1381 +#define DMA_STATUS_RPS BIT(8) /* receive process stopped */
1382 +#define DMA_STATUS_ETI BIT(10) /* early transmit interrupt */
1383 +#define DMA_STATUS_FBE BIT(13) /* fatal bus interrupt */
1384 +#define DMA_STATUS_ERI BIT(14) /* early receive interrupt */
1385 +#define DMA_STATUS_AIS BIT(15) /* abnormal interrupt summary */
1386 +#define DMA_STATUS_NIS BIT(16) /* normal interrupt summary */
1387 +#define DMA_STATUS_RS_SHIFT 17 /* receive process state */
1388 +#define DMA_STATUS_TS_SHIFT 20 /* transmit process state */
1389 +#define DMA_STATUS_EB_SHIFT 23 /* error bits */
1391 +#define DMA_CONTROL_SR BIT(1) /* start receive */
1392 +#define DMA_CONTROL_ST BIT(13) /* start transmit */
1393 +#define DMA_CONTROL_SF BIT(21) /* store and forward */
1396 + volatile unsigned int status; /* OWN, Device control and status. */
1397 + volatile unsigned int devcs; /* pkt Control bits + Length */
1398 + volatile unsigned int addr; /* Current Address. */
1399 + volatile unsigned int descr; /* Next descriptor in chain. */
1403 + * New Combo structure for Both Eth0 AND eth1
1405 + * Don't directly access MII related regs since phy chip could be actually
1406 + * connected to another ethernet block.
1409 + volatile unsigned int mac_control; /* 0x00 */
1410 + volatile unsigned int mac_addr[2]; /* 0x04 - 0x08 */
1411 + volatile unsigned int mcast_table[2]; /* 0x0c - 0x10 */
1412 + volatile unsigned int __mii_addr; /* 0x14 */
1413 + volatile unsigned int __mii_data; /* 0x18 */
1414 + volatile unsigned int flow_control; /* 0x1c */
1415 + volatile unsigned int vlan_tag; /* 0x20 */
1416 + volatile unsigned int pad[7]; /* 0x24 - 0x3c */
1417 + volatile unsigned int ucast_table[8]; /* 0x40-0x5c */
1421 + volatile unsigned int mii_addr;
1422 + volatile unsigned int mii_data;
1425 +/********************************************************************
1426 + * Interrupt controller
1427 + ********************************************************************/
1430 + volatile unsigned int wdog_control; /* 0x08 */
1431 + volatile unsigned int wdog_timer; /* 0x0c */
1432 + volatile unsigned int misc_status; /* 0x10 */
1433 + volatile unsigned int misc_mask; /* 0x14 */
1434 + volatile unsigned int global_status; /* 0x18 */
1435 + volatile unsigned int reserved; /* 0x1c */
1436 + volatile unsigned int reset_control; /* 0x20 */
1439 +/********************************************************************
1441 + ********************************************************************/
1443 + volatile unsigned int bus_mode; /* 0x00 (CSR0) */
1444 + volatile unsigned int xmt_poll; /* 0x04 (CSR1) */
1445 + volatile unsigned int rcv_poll; /* 0x08 (CSR2) */
1446 + volatile unsigned int rcv_base; /* 0x0c (CSR3) */
1447 + volatile unsigned int xmt_base; /* 0x10 (CSR4) */
1448 + volatile unsigned int status; /* 0x14 (CSR5) */
1449 + volatile unsigned int control; /* 0x18 (CSR6) */
1450 + volatile unsigned int intr_ena; /* 0x1c (CSR7) */
1451 + volatile unsigned int rcv_missed; /* 0x20 (CSR8) */
1452 + volatile unsigned int reserved[11]; /* 0x24-0x4c (CSR9-19) */
1453 + volatile unsigned int cur_tx_buf_addr; /* 0x50 (CSR20) */
1454 + volatile unsigned int cur_rx_buf_addr; /* 0x50 (CSR21) */
1458 + * Struct private for the Sibyte.
1460 + * Elements are grouped so variables used by the tx handling goes
1461 + * together, and will go into the same cache lines etc. in order to
1462 + * avoid cache line contention between the rx and tx handling on SMP.
1464 + * Frequently accessed variables are put at the beginning of the
1465 + * struct to help the compiler generate better/shorter code.
1467 +struct ar231x_private {
1468 + struct net_device *dev;
1472 + volatile MII *phy_regs;
1473 + volatile ETHERNET_STRUCT *eth_regs;
1474 + volatile DMA *dma_regs;
1475 + struct ar231x_eth *cfg;
1477 + spinlock_t lock; /* Serialise access to device */
1479 + /* RX and TX descriptors, must be adjacent */
1480 + ar231x_descr_t *rx_ring;
1481 + ar231x_descr_t *tx_ring;
1483 + struct sk_buff **rx_skb;
1484 + struct sk_buff **tx_skb;
1494 + /* Misc elements */
1502 + struct timer_list link_timer;
1503 + unsigned short phy; /* merlot phy = 1, samsung phy = 0x1f */
1504 + unsigned short mac;
1505 + unsigned short link; /* 0 - link down, 1 - link up */
1508 + struct tasklet_struct rx_tasklet;
1511 + struct phy_device *phy_dev;
1512 + struct mii_bus *mii_bus;
1517 +static int ar231x_init(struct net_device *dev);
1519 +static void ar231x_tx_timeout(struct net_device *dev);
1521 +static int ar231x_restart(struct net_device *dev);
1522 +static void ar231x_load_rx_ring(struct net_device *dev, int bufs);
1523 +static irqreturn_t ar231x_interrupt(int irq, void *dev_id);
1524 +static int ar231x_open(struct net_device *dev);
1525 +static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev);
1526 +static int ar231x_close(struct net_device *dev);
1527 +static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd);
1528 +static void ar231x_init_cleanup(struct net_device *dev);
1529 +static int ar231x_setup_timer(struct net_device *dev);
1530 +static void ar231x_link_timer_fn(unsigned long data);
1531 +static void ar231x_check_link(struct net_device *dev);
1533 +#endif /* _AR2313_H_ */