target/linux/ath79/dts/qca9563_rosinson_wr818.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca956x.dtsi"
   8
   9 / {
  10         model = "ROSINSON WR818";
  11         compatible = "rosinson,wr818", "qca,qca9560";
  12
  13         chosen {
  14                 bootargs = "console=ttyS0,115200n8";
  15         };
  16
  17         aliases {
  18                 led-boot = &system;
  19                 led-failsafe = &system;
  20                 led-running = &system;
  21                 led-upgrade = &system;
  22         };
  23
  24         gpio_leds: leds {
  25                 compatible = "gpio-leds";
  26
  27                 system: system {
  28                         label = "wr818:red:system";
  29                         gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
  30                 };
  31
  32                 wifi_2g {
  33                         label = "wr818:red:wifi2g";
  34                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  35                         linux,default-trigger = "phy0tpt";
  36                 };
  37         };
  38
  39         keys {
  40                 compatible = "gpio-keys";
  41
  42                 reset {
  43                         label = "reset";
  44                         linux,code = <KEY_RESTART>;
  45                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  46                         debounce-interval = <60>;
  47                 };
  48         };
  49 };
  50
  51 &uart {
  52         status = "okay";
  53 };
  54
  55 &gpio {
  56         status = "okay";
  57 };
  58
  59 &spi {
  60         num-cs = <1>;
  61
  62         status = "okay";
  63
  64         flash@0 {
  65                 compatible = "jedec,spi-nor";
  66                 reg = <0>;
  67                 spi-max-frequency = <25000000>;
  68
  69                 partitions {
  70                         compatible = "fixed-partitions";
  71                         #address-cells = <1>;
  72                         #size-cells = <1>;
  73
  74                         partition@0 {
  75                                 label = "u-boot";
  76                                 reg = <0x000000 0x040000>;
  77                                 read-only;
  78                         };
  79
  80                         partition@40000 {
  81                                 label = "u-boot-env";
  82                                 reg = <0x040000 0x010000>;
  83                                 read-only;
  84                         };
  85
  86                         partition@50000 {
  87                                 label = "firmware";
  88                                 reg = <0x050000 0xf80000>;
  89                         };
  90
  91                         info: partition@fd0000 {
  92                                 label = "factory";
  93                                 reg = <0xfd0000 0x010000>;
  94                                 read-only;
  95                         };
  96
  97                         art: partition@ff0000 {
  98                                 label = "art";
  99                                 reg = <0xff0000 0x010000>;
 100                                 read-only;
 101                         };
 102                 };
 103         };
 104 };
 105
 106 &mdio0 {
 107         status = "okay";
 108
 109         phy-mask = <0>;
 110         phy0: ethernet-phy@0 {
 111                 reg = <0>;
 112                 phy-mode = "sgmii";
 113
 114                 qca,ar8327-initvals = <
 115                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 116                         0x7c 0x0000007e /* PORT0_STATUS */
 117                 >;
 118         };
 119 };
 120
 121 &eth0 {
 122         status = "okay";
 123
 124         mtd-mac-address = <&info 0x0>;
 125         phy-mode = "sgmii";
 126         phy-handle = <&phy0>;
 127 };
 128
 129 &wmac {
 130         status = "okay";
 131         mtd-cal-data = <&art 0x1000>;
 132 };
 133
 134 &usb_phy0 {
 135         status = "okay";
 136 };
 137
 138 &usb0 {
 139         #address-cells = <1>;
 140         #size-cells = <0>;
 141         status = "okay";
 142
 143         port@1 {
 144                 reg = <1>;
 145                 #trigger-source-cells = <0>;
 146         };
 147 };
 148
 149 &usb_phy1 {
 150         status = "okay";
 151 };
 152
 153 &usb1 {
 154         #address-cells = <1>;
 155         #size-cells = <0>;
 156         status = "okay";
 157
 158         port@2 {
 159                 reg = <2>;
 160                 #trigger-source-cells = <0>;
 161         };
 162 };