target/linux/ath79/dts/qca9563_glinet_gl-ar750s.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca956x.dtsi"
   8
   9 / {
  10         compatible = "glinet,gl-ar750s", "qca,qca9563";
  11         model = "GL.iNet GL-AR750S";
  12
  13         chosen {
  14                 bootargs = "console=ttyS0,115200n8";
  15         };
  16
  17         aliases {
  18                 led-boot = &power;
  19                 led-failsafe = &power;
  20                 led-running = &power;
  21                 led-upgrade = &power;
  22         };
  23
  24         keys {
  25                 compatible = "gpio-keys";
  26
  27                 pinctrl-names = "default";
  28                 pinctrl-0 = <&jtag_disable_pins>;
  29
  30                 reset {
  31                         label = "reset";
  32                         linux,code = <KEY_RESTART>;
  33                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  34                 };
  35
  36                 mode {
  37                         label = "mode";
  38                         linux,code = <BTN_0>;
  39                         linux,input-type = <EV_SW>;
  40                         gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
  41                 };
  42         };
  43
  44         leds {
  45                 compatible = "gpio-leds";
  46
  47                 power: power {
  48                         label = "gl-ar750s:green:power";
  49                         gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
  50                         default-state = "keep";
  51                 };
  52
  53                 wlan2g {
  54                         label = "gl-ar750s:green:wlan2g";
  55                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  56                         linux,default-trigger = "phy1tpt";
  57                 };
  58
  59                 wlan5g {
  60                         label = "gl-ar750s:green:wlan5g";
  61                         gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
  62                         linux,default-trigger = "phy0tpt";
  63                 };
  64         };
  65
  66         i2c: i2c {
  67                 compatible = "i2c-gpio";
  68
  69                 sda-gpios = <&gpio  5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  70                 scl-gpios = <&gpio 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  71         };
  72
  73         usb_vbus: regulator-usb-vbus {
  74                 compatible = "regulator-fixed";
  75
  76                 regulator-name = "USB_VBUS";
  77
  78                 regulator-min-microvolt = <5000000>;
  79                 regulator-max-microvolt = <5000000>;
  80                 regulator-always-on;
  81
  82                 gpio = <&gpio 7 GPIO_ACTIVE_HIGH>;
  83                 enable-active-high;
  84         };
  85 };
  86
  87 &spi {
  88         status = "okay";
  89         num-cs = <0>;
  90
  91         flash@0 {
  92                 compatible = "jedec,spi-nor";
  93                 reg = <0>;
  94                 spi-max-frequency = <25000000>;
  95
  96                 partitions {
  97                         compatible = "fixed-partitions";
  98                         #address-cells = <1>;
  99                         #size-cells = <1>;
 100
 101                         partition@0 {
 102                                 label = "u-boot";
 103                                 reg = <0x000000 0x040000>;
 104                                 read-only;
 105                         };
 106
 107                         partition@40000 {
 108                                 label = "u-boot-env";
 109                                 reg = <0x040000 0x010000>;
 110                         };
 111
 112                         art: partition@50000 {
 113                                 label = "art";
 114                                 reg = <0x050000 0x010000>;
 115                                 read-only;
 116                         };
 117
 118                         partition@60000 {
 119                                 compatible = "denx,uimage";
 120                                 label = "firmware";
 121                                 reg = <0x060000 0xfa0000>;
 122                         };
 123                 };
 124         };
 125 };
 126
 127 &pcie {
 128         status = "okay";
 129 };
 130
 131 &uart {
 132         status = "okay";
 133 };
 134
 135 &usb0 {
 136         status = "okay";
 137         vbus-supply = <&usb_vbus>;
 138 };
 139
 140 &usb_phy0 {
 141         status = "okay";
 142 };
 143
 144 &usb1 {
 145         status = "okay";
 146 };
 147
 148 &usb_phy1 {
 149         status = "okay";
 150 };
 151
 152 &mdio0 {
 153         status = "okay";
 154         phy-mask = <0>;
 155
 156         phy0: ethernet-phy@0 {
 157                 reg = <0>;
 158                 phy-mode = "sgmii";
 159                 qca,ar8327-initvals = <
 160                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 161                         0x7c 0x0000007e /* PORT0_STATUS */
 162                 >;
 163         };
 164 };
 165
 166 &eth0 {
 167         status = "okay";
 168
 169         mtd-mac-address = <&art 0x0>;
 170         phy-handle = <&phy0>;
 171 };
 172
 173 &wmac {
 174         status = "okay";
 175         mtd-cal-data = <&art 0x1000>;
 176         mtd-mac-address = <&art 0x1002>;
 177 };