target/linux/ath79/dts/qca9558_ocedo_ursus.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca9557.dtsi"
   8
   9 / {
  10         compatible = "ocedo,ursus", "qca,qca9558";
  11         model = "OCEDO Ursus";
  12
  13         chosen {
  14                 bootargs = "console=ttyS0,115200n8";
  15         };
  16
  17         leds {
  18                 compatible = "gpio-leds";
  19
  20                 wifi2 {
  21                         label = "ursus:green:wlan2g";
  22                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  23                         linux,default-trigger = "phy1tpt";
  24                 };
  25
  26                 wifi5 {
  27                         label = "ursus:green:wlan5g";
  28                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  29                         linux,default-trigger = "phy0tpt";
  30                 };
  31
  32         };
  33
  34 };
  35
  36 &pcie1 {
  37         status = "okay";
  38 };
  39
  40 &uart {
  41         status = "okay";
  42 };
  43
  44 &pll {
  45         clocks = <&extosc>;
  46 };
  47
  48 &spi {
  49         status = "okay";
  50         num-cs = <1>;
  51
  52         flash@0 {
  53                 compatible = "jedec,spi-nor";
  54                 reg = <0>;
  55                 spi-max-frequency = <25000000>;
  56
  57                 partitions {
  58                         compatible = "fixed-partitions";
  59                         #address-cells = <1>;
  60                         #size-cells = <1>;
  61
  62                         uboot: partition@0 {
  63                                 label = "u-boot";
  64                                 reg = <0x000000 0x040000>;
  65                                 read-only;
  66                         };
  67
  68                         partition@40000 {
  69                                 label = "u-boot-env";
  70                                 reg = <0x040000 0x010000>;
  71                         };
  72
  73                         partition@50000 {
  74                                 compatible = "denx,uimage";
  75                                 label = "firmware";
  76                                 reg = <0x050000 0x740000>;
  77                         };
  78
  79                         partition@790000 {
  80                                 label = "vendor";
  81                                 reg = <0x790000 0x740000>;
  82                                 read-only;
  83                         };
  84
  85                         partition@ed0000 {
  86                                 label = "data";
  87                                 reg = <0xed0000 0x110000>;
  88                                 read-only;
  89                         };
  90
  91                         partition@fe0000 {
  92                                 label = "id";
  93                                 reg = <0xfe0000 0x010000>;
  94                                 read-only;
  95                         };
  96
  97                         art: partition@ff0000 {
  98                                 label = "art";
  99                                 reg = <0xff0000 0x010000>;
 100                                 read-only;
 101                         };
 102                 };
 103         };
 104 };
 105
 106 &wmac {
 107         status = "okay";
 108
 109         mtd-cal-data = <&art 0x1000>;
 110         mtd-mac-address = <&art 0x06>;
 111 };
 112
 113 &mdio0 {
 114         status = "okay";
 115
 116         phy1: ethernet-phy@1 {
 117                 reg = <1>;
 118         };
 119
 120         phy2: ethernet-phy@2 {
 121                 reg = <2>;
 122         };
 123 };
 124
 125 &eth0 {
 126         status = "okay";
 127         mtd-mac-address = <&art 0x00>;
 128         phy-handle = <&phy1>;
 129         pll-data = <0xa6000000 0x80000101 0x80001313>;
 130
 131         gmac_config: gmac-config {
 132                 device = <&gmac>;
 133
 134                 rxdv-delay = <3>;
 135                 rxd-delay = <3>;
 136                 txen-delay = <0>;
 137                 txd-delay = <0>;
 138                 rgmii-enabled = <1>;
 139         };
 140 };
 141
 142 &eth1 {
 143         status = "okay";
 144         mtd-mac-address = <&art 0x12>;
 145         phy-handle = <&phy2>;
 146         pll-data = <0x3000101 0x101 0x1313>;
 147 };