target/linux/ath79/dts/qca9558_comfast_cf-wr650ac.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca9557.dtsi"
   8
   9 / {
  10         chosen {
  11                 bootargs = "console=ttyS0,115200n8";
  12         };
  13
  14         keys {
  15                 compatible = "gpio-keys";
  16
  17                 button0 {
  18                         label = "reset";
  19                         linux,code = <KEY_RESTART>;
  20                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  21                         debounce-interval = <60>;
  22                 };
  23         };
  24
  25         watchdog {
  26                 compatible = "linux,wdt-gpio";
  27                 gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  28                 hw_algo = "toggle";
  29                 hw_margin_ms = <500>;
  30                 always-running;
  31         };
  32 };
  33
  34 &pcie0 {
  35         status = "okay";
  36 };
  37
  38 &uart {
  39         status = "okay";
  40 };
  41
  42 &usb_phy0 {
  43         status = "okay";
  44 };
  45
  46 &usb0 {
  47         status = "okay";
  48 };
  49
  50 &mdio0 {
  51         status = "okay";
  52
  53         switch0@1f {
  54                 compatible = "qca,ar8327";
  55                 reg = <0x1f>;
  56                 qca,ar8327-initvals = <
  57                         0x04 0x87600000 /* PORT0 PAD MODE CTRL */
  58                         0x0c 0x00080080 /* PORT6 PAD MODE CTRL */
  59                         0x10 0x81000080 /* POWER_ON_STRIP */
  60                         0x7c 0x0000007e /* PORT0_STATUS */
  61                         0x94 0x0000007e /* PORT6 STATUS */
  62                         >;
  63         };
  64 };
  65
  66 &eth0 {
  67         status = "okay";
  68
  69         pll-data = <0xa6000000 0x00000101 0x00001616>;
  70         mtd-mac-address = <&art 0x0>;
  71         fixed-link {
  72                 speed = <1000>;
  73                 full-duplex;
  74         };
  75 };
  76
  77 &eth1 {
  78         status = "okay";
  79
  80         pll-data = <0x03000101 0x00000101 0x00001616>;
  81         mtd-mac-address = <&art 0x6>;
  82         fixed-link {
  83                 speed = <1000>;
  84                 full-duplex;
  85         };
  86 };
  87
  88 &wmac {
  89         status = "okay";
  90
  91         mtd-cal-data = <&art 0x1000>;
  92         mtd-mac-address = <&art 0x18>;
  93 };
  94
  95 // This node is required for the Ethernet ports to work correctly.
  96 &gpio {
  97         status = "okay";
  98 };