target/linux/ath79/dts/ar9344_winchannel_wb2000.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9344.dtsi"
   8
   9 / {
  10         model = "Winchannel WB2000";
  11         compatible = "winchannel,wb2000", "qca,ar9344";
  12
  13         chosen {
  14                 bootargs = "console=ttyS0,115200n8";
  15         };
  16
  17         aliases {
  18                 led-boot = &led_system;
  19                 led-failsafe = &led_system;
  20                 led-running = &led_system;
  21                 led-upgrade = &led_system;
  22         };
  23
  24         i2c {
  25                 compatible = "i2c-gpio";
  26                 gpios = <&gpio 17 GPIO_ACTIVE_HIGH
  27                          &gpio 16 GPIO_ACTIVE_HIGH
  28                         >;
  29                 #address-cells = <1>;
  30                 #size-cells = <0>;
  31
  32                 rtc@68 {
  33                         compatible = "dallas,ds1339";
  34                         reg = <0x68>;
  35                 };
  36         };
  37
  38         leds {
  39                 compatible = "gpio-leds";
  40
  41                 wlan2g {
  42                         label = "wb2000:green:2g";
  43                         gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
  44                         linux,default-trigger = "phy0tpt";
  45                 };
  46
  47                 usb {
  48                         label = "wb2000:green:usb";
  49                         gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
  50                         trigger-sources = <&hub_port1>, <&hub_port2>;
  51                         linux,default-trigger = "usbport";
  52                 };
  53
  54                 led_system: system {
  55                         label = "wb2000:green:system";
  56                         gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
  57                         default-state = "on";
  58                 };
  59         };
  60
  61         keys {
  62                 compatible = "gpio-keys";
  63
  64                 reset {
  65                         linux,code = <KEY_RESTART>;
  66                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  67                         debounce-interval = <60>;
  68                 };
  69         };
  70
  71         ath9k-leds {
  72                 compatible = "gpio-leds";
  73
  74                 wlan {
  75                         label = "wb2000:green:5g";
  76                         gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
  77                         linux,default-trigger = "phy1tpt";
  78                 };
  79         };
  80 };
  81
  82 &ref {
  83         clock-frequency = <40000000>;
  84 };
  85
  86 &uart {
  87         status = "okay";
  88 };
  89
  90 &spi {
  91         num-cs = <1>;
  92
  93         status = "okay";
  94
  95         flash@0 {
  96                 compatible = "jedec,spi-nor";
  97                 reg = <0>;
  98                 spi-max-frequency = <25000000>;
  99
 100                 partitions {
 101                         compatible = "fixed-partitions";
 102                         #address-cells = <1>;
 103                         #size-cells = <1>;
 104
 105                         partition@0 {
 106                                 label = "u-boot";
 107                                 reg = <0x0 0x40000>;
 108                                 read-only;
 109                         };
 110
 111                         partition@40000 {
 112                                 label = "u-boot-env";
 113                                 reg = <0x40000 0x10000>;
 114                                 read-only;
 115                         };
 116
 117                         partition@50000 {
 118                                 label = "firmware";
 119                                 reg = <0x50000 0xf80000>;
 120                                 compatible = "denx,uimage";
 121                         };
 122
 123                         partition@fd0000 {
 124                                 label = "nvram";
 125                                 reg = <0xfd0000 0x10000>;
 126                                 read-only;
 127                         };
 128
 129                         art: partition@fe0000 {
 130                                 label = "art";
 131                                 reg = <0xfe0000 0x10000>;
 132                                 read-only;
 133                         };
 134
 135                         addr: partition@ff0000 {
 136                                 label = "addr";
 137                                 reg = <0xff0000 0x10000>;
 138                                 read-only;
 139                         };
 140                 };
 141         };
 142 };
 143
 144 &pcie {
 145         status = "okay";
 146
 147         ath9k: wifi@0,0 {
 148                 compatible = "pci168c,0030";
 149                 reg = <0x0000 0 0 0 0>;
 150                 qca,no-eeprom;
 151                 mtd-mac-address = <&addr 0x0>;
 152                 mtd-mac-address-increment = <0x10>;
 153                 #gpio-cells = <2>;
 154                 gpio-controller;
 155         };
 156 };
 157
 158 &usb {
 159         #address-cells = <1>;
 160         #size-cells = <0>;
 161         status = "okay";
 162
 163         port@1 {
 164                 #address-cells = <1>;
 165                 #size-cells = <0>;
 166                 reg = <1>;
 167                 #trigger-source-cells = <0>;
 168
 169                 hub_port1: port@1 {
 170                         reg = <1>;
 171                         #trigger-source-cells = <0>;
 172                 };
 173
 174                 hub_port2: port@2 {
 175                         reg = <2>;
 176                         #trigger-source-cells = <0>;
 177                 };
 178         };
 179 };
 180
 181 &usb_phy {
 182         status = "okay";
 183 };
 184
 185 &wmac {
 186         status = "okay";
 187
 188         mtd-cal-data = <&art 0x1000>;
 189         mtd-mac-address = <&addr 0x0>;
 190 };
 191
 192 &mdio0 {
 193         status = "okay";
 194
 195         phy-mask = <0x10>;
 196
 197         phy4: ethernet-phy@4 {
 198                 reg = <4>;
 199         };
 200 };
 201
 202 &eth0 {
 203         status = "okay";
 204
 205         pll-data = <0xe000000 0x04000101 0x04001313>;
 206
 207         mtd-mac-address = <&addr 0x0>;
 208         mtd-mac-address-increment = <0x21>;
 209
 210         phy-mode = "rgmii-rxid";
 211         phy-handle = <&phy4>;
 212
 213         gmac-config {
 214                 device = <&gmac>;
 215                 rgmii-gmac0 = <1>;
 216                 rxd-delay = <1>;
 217                 rxdv-delay = <1>;
 218         };
 219 };