target/linux/ath79/dts/ar9344_pcs_cr5000.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9344.dtsi"
   8
   9 / {
  10         model = "PowerCloud Systems CR5000";
  11         compatible = "pcs,cr5000", "qca,ar9344";
  12
  13         aliases {
  14                 serial0 = &uart;
  15                 led-status = &status;
  16         };
  17
  18         keys {
  19                 compatible = "gpio-keys-polled";
  20                 poll-interval = <20>;
  21
  22                 pinctrl-names = "default";
  23                 pinctrl-0 = <&jtag_disable_pins>;
  24
  25                 reset {
  26                         label = "Reset button";
  27                         linux,code = <KEY_RESTART>;
  28                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  29                         debounce-interval = <60>;
  30                 };
  31
  32                 wps {
  33                         label = "WPS button";
  34                         linux,code = <KEY_WPS_BUTTON>;
  35                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  36                         debounce-interval = <60>;
  37                 };
  38         };
  39
  40         leds {
  41                 compatible = "gpio-leds";
  42
  43                 status: power {
  44                         label = "pcs:amber:power";
  45                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>,
  46                                 <&gpio 4 GPIO_ACTIVE_LOW>;
  47                         default-state = "on";
  48                 };
  49
  50                 wlan2g {
  51                         label = "pcs:blue:wlan";
  52                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  53                         default-state = "off";
  54                         linux,default-trigger = "phy0tpt";
  55                 };
  56
  57                 wps_white {
  58                         label = "pcs:white:wps";
  59                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  60                         default-state = "off";
  61                 };
  62         };
  63
  64 };
  65
  66 &ref {
  67         clock-frequency = <25000000>;
  68 };
  69
  70 &uart {
  71         status = "okay";
  72 };
  73
  74 &gpio {
  75         status = "okay";
  76 };
  77
  78 &spi {
  79         num-cs = <1>;
  80
  81         status = "okay";
  82
  83         flash@0 {
  84                 compatible = "jedec,spi-nor";
  85                 reg = <0>;
  86                 spi-max-frequency = <25000000>;
  87
  88                 partitions {
  89                         compatible = "fixed-partitions";
  90                         #address-cells = <1>;
  91                         #size-cells = <1>;
  92
  93                         uboot: partition@0 {
  94                                 label = "u-boot";
  95                                 reg = <0x000000 0x040000>;
  96                                 read-only;
  97                         };
  98
  99                         partition@40000 {
 100                                 label = "u-boot-env";
 101                                 reg = <0x040000 0x010000>;
 102                                 read-only;
 103                         };
 104
 105                         partition@50000 {
 106                                 label = "firmware";
 107                                 reg = <0x050000 0x07a0000>;
 108                         };
 109
 110                         art: partition@7f0000 {
 111                                 label = "art";
 112                                 reg = <0x7f0000 0x010000>;
 113                                 read-only;
 114                         };
 115                 };
 116         };
 117 };
 118
 119 &usb {
 120         status = "okay";
 121         #address-cells = <1>;
 122         #size-cells = <0>;
 123
 124         hub_port1: port@1 {
 125                 reg = <1>;
 126                 #trigger-source-cells = <0>;
 127         };
 128 };
 129
 130 &usb_phy {
 131         status = "okay";
 132 };
 133
 134 &pcie {
 135         status = "okay";
 136
 137         ath9k: wifi@0,0 {
 138                 compatible = "pci168c,0030";
 139                 reg = <0x0000 0 0 0 0>;
 140                 mtd-mac-address = <&art 0x5002>;
 141                 #gpio-cells = <2>;
 142                 gpio-controller;
 143         };
 144 };
 145
 146 &mdio0 {
 147         status = "okay";
 148
 149         phy-mask = <0>;
 150
 151         phy0: ethernet-phy@0 {
 152                 reg = <0>;
 153                 phy-mode = "rgmii";
 154                 qca,ar8327-initvals = <
 155                         0x04 0x07600000 /* PORT0 PAD MODE CTRL */
 156                         0x10 0x81000080 /* POWER_ON_STRAP */
 157                         0x50 0xcc35cc35 /* LED_CTRL0 */
 158                         0x54 0xca35ca35 /* LED_CTRL1 */
 159                         0x58 0xc935c935 /* LED_CTRL2 */
 160                         0x5c 0x03ffff00 /* LED_CTRL3 */
 161                         0x7c 0x0000007e /* PORT0_STATUS */
 162                 >;
 163         };
 164 };
 165
 166 &eth0 {
 167         #address-cells = <1>;
 168         #size-cells = <0>;
 169         status = "okay";
 170
 171         /* default for ar934x, except for 1000M */
 172         pll-data = <0x06000000 0x00000101 0x00001616>;
 173
 174         mtd-mac-address = <&art 0x0>;
 175
 176         phy-mode = "rgmii";
 177         phy-handle = <&phy0>;
 178
 179
 180         aliases {
 181                 ag0 = &eth1;
 182         };
 183
 184         port@0 {
 185                 compatible = "swconfig,port";
 186                 reg = <0>;
 187                 swconfig,segment = "lan";
 188                 swconfig,portmap = <1 1>;
 189         };
 190
 191         port@1 {
 192                 compatible = "swconfig,port";
 193                 reg = <1>;
 194                 swconfig,segment = "lan";
 195                 swconfig,portmap = <2 2>;
 196         };
 197
 198         port@2 {
 199                 compatible = "swconfig,port";
 200                 reg = <2>;
 201                 swconfig,segment = "lan";
 202                 swconfig,portmap = <3 3>;
 203         };
 204
 205         port@3 {
 206                 compatible = "swconfig,port";
 207                 reg = <3>;
 208                 swconfig,segment = "lan";
 209                 swconfig,portmap = <4 4>;
 210         };
 211
 212         port@4 {
 213                 compatible = "swconfig,port";
 214                 reg = <4>;
 215                 swconfig,segment = "wan";
 216                 swconfig,portmap = <5 5>;
 217         };
 218
 219 };
 220
 221 &wmac {
 222         status = "okay";
 223
 224         mtd-cal-data = <&art 0x1000>;
 225         mtd-mac-address = <&art 0x1002>;
 226 };