target/linux/ath79/dts/ar9331_tplink_tl-wr703n_tl-mr10u.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "ar9331.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         aliases {
  10                 led-boot = &led_system;
  11                 led-failsafe = &led_system;
  12                 led-running = &led_system;
  13                 led-upgrade = &led_system;
  14                 label-mac-device = &eth0;
  15         };
  16
  17         keys {
  18                 compatible = "gpio-keys";
  19
  20                 reset {
  21                         label = "reset";
  22                         linux,code = <KEY_RESTART>;
  23                         gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
  24                         debounce-interval = <60>;
  25                 };
  26         };
  27
  28         leds {
  29                 compatible = "gpio-leds";
  30
  31                 led_system: system {
  32                         label = "blue:system";
  33                         gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
  34                 };
  35         };
  36
  37         reg_usb_vbus: reg_usb_vbus {
  38                 compatible = "regulator-fixed";
  39                 regulator-name = "usb_vbus";
  40                 regulator-min-microvolt = <5000000>;
  41                 regulator-max-microvolt = <5000000>;
  42                 enable-active-high;
  43         };
  44 };
  45
  46 &spi {
  47         status = "okay";
  48
  49         flash@0 {
  50                 compatible = "jedec,spi-nor";
  51                 reg = <0>;
  52                 spi-max-frequency = <25000000>;
  53
  54                 partitions {
  55                         compatible = "fixed-partitions";
  56                         #address-cells = <1>;
  57                         #size-cells = <1>;
  58
  59                         uboot: partition@0 {
  60                                 reg = <0x0 0x20000>;
  61                                 label = "u-boot";
  62                                 read-only;
  63                         };
  64
  65                         partition@20000 {
  66                                 compatible = "tplink,firmware";
  67                                 reg = <0x20000 0x3d0000>;
  68                                 label = "firmware";
  69                         };
  70
  71                         art: partition@3f0000 {
  72                                 reg = <0x3f0000 0x10000>;
  73                                 label = "art";
  74                                 read-only;
  75                         };
  76                 };
  77         };
  78 };
  79
  80 &eth0 {
  81         status = "okay";
  82
  83         nvmem-cells = <&macaddr_uboot_1fc00>;
  84         nvmem-cell-names = "mac-address";
  85
  86         gmac-config {
  87                 device = <&gmac>;
  88
  89                 switch-phy-addr-swap = <0>;
  90                 switch-phy-swap = <0>;
  91         };
  92 };
  93
  94 &eth1 {
  95         status = "okay";
  96
  97         compatible = "syscon", "simple-mfd";
  98 };
  99
 100 &usb {
 101         dr_mode = "host";
 102         vbus-supply = <&reg_usb_vbus>;
 103         status = "okay";
 104 };
 105
 106 &usb_phy {
 107         status = "okay";
 108 };
 109
 110 &wmac {
 111         status = "okay";
 112
 113         mtd-cal-data = <&art 0x1000>;
 114         nvmem-cells = <&macaddr_uboot_1fc00>;
 115         nvmem-cell-names = "mac-address";
 116 };
 117
 118 &uboot {
 119         compatible = "nvmem-cells";
 120         #address-cells = <1>;
 121         #size-cells = <1>;
 122
 123         macaddr_uboot_1fc00: macaddr@1fc00 {
 124                 reg = <0x1fc00 0x6>;
 125         };
 126 };