target/linux/ath79/dts/ar9331_tplink_tl-wr703n_tl-mr10u.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9331.dtsi"
   8
   9 / {
  10         aliases {
  11                 serial0 = &uart;
  12                 led-boot = &system;
  13                 led-failsafe = &system;
  14                 led-running = &system;
  15                 led-upgrade = &system;
  16                 label-mac-device = &eth0;
  17         };
  18
  19         keys {
  20                 compatible = "gpio-keys";
  21
  22                 reset {
  23                         label = "reset";
  24                         linux,code = <KEY_RESTART>;
  25                         gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
  26                         debounce-interval = <60>;
  27                 };
  28         };
  29
  30         leds {
  31                 compatible = "gpio-leds";
  32
  33                 system: system {
  34                         label = "tl-wr703n:blue:system";
  35                         gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
  36                 };
  37         };
  38
  39         reg_usb_vbus: reg_usb_vbus {
  40                 compatible = "regulator-fixed";
  41                 regulator-name = "usb_vbus";
  42                 regulator-min-microvolt = <5000000>;
  43                 regulator-max-microvolt = <5000000>;
  44                 enable-active-high;
  45         };
  46 };
  47
  48 &spi {
  49         status = "okay";
  50         num-cs = <1>;
  51
  52         flash@0 {
  53                 compatible = "jedec,spi-nor";
  54                 reg = <0>;
  55                 spi-max-frequency = <25000000>;
  56
  57                 partitions {
  58                         compatible = "fixed-partitions";
  59                         #address-cells = <1>;
  60                         #size-cells = <1>;
  61
  62                         uboot: partition@0 {
  63                                 reg = <0x0 0x20000>;
  64                                 label = "u-boot";
  65                                 read-only;
  66                         };
  67
  68                         firmware: partition@20000 {
  69                                 compatible = "tplink,firmware";
  70                                 reg = <0x20000 0x3d0000>;
  71                                 label = "firmware";
  72                         };
  73
  74                         art: partition@3f0000 {
  75                                 reg = <0x3f0000 0x10000>;
  76                                 label = "art";
  77                                 read-only;
  78                         };
  79                 };
  80         };
  81 };
  82
  83 &eth0 {
  84         status = "okay";
  85
  86         mtd-mac-address = <&uboot 0x1fc00>;
  87
  88         gmac-config {
  89                 device = <&gmac>;
  90
  91                 switch-phy-addr-swap = <0>;
  92                 switch-phy-swap = <0>;
  93         };
  94 };
  95
  96 &eth1 {
  97         status = "okay";
  98         compatible = "syscon", "simple-mfd";
  99 };
 100
 101 &gpio {
 102         status = "okay";
 103 };
 104
 105 &uart {
 106         status = "okay";
 107 };
 108
 109 &usb {
 110         dr_mode = "host";
 111         vbus-supply = <&reg_usb_vbus>;
 112         status = "okay";
 113 };
 114
 115 &usb_phy {
 116         status = "okay";
 117 };
 118
 119 &wmac {
 120         status = "okay";
 121         mtd-cal-data = <&art 0x1000>;
 122         mtd-mac-address = <&uboot 0x1fc00>;
 123 };