target/linux/ath79/dts/ar9331_etactica_eg200.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9331.dtsi"
   8
   9 / {
  10         model = "eTactica EG200";
  11         compatible = "etactica,eg200", "qca,ar9331";
  12
  13         aliases {
  14                 serial0 = &uart;
  15         };
  16
  17         keys {
  18                 compatible = "gpio-keys-polled";
  19                 poll-interval = <50>;
  20
  21                 restore {
  22                         linux,code = <KEY_WPS_BUTTON>;
  23                         gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
  24                 };
  25         };
  26
  27         leds {
  28                 compatible = "gpio-leds";
  29
  30                 modbus {
  31                         label = "eg200:red:modbus";
  32                         gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
  33                 };
  34
  35                 etactica {
  36                         label = "eg200:red:etactica";
  37                         gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
  38                 };
  39
  40                 eth0 {
  41                         label = "eg200:red:eth0";
  42                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  43                 };
  44
  45                 wlan {
  46                         label = "eg200:red:wlan";
  47                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  48                         linux,default-trigger = "phy0tpt";
  49                 };
  50         };
  51 };
  52
  53 &uart {
  54         status = "okay";
  55 };
  56
  57 &gpio {
  58         status = "okay";
  59 };
  60
  61 &usb {
  62         dr_mode = "host";
  63         status = "okay";
  64 };
  65
  66 &usb_phy {
  67         status = "okay";
  68 };
  69
  70 &eth0 {
  71         status = "okay";
  72         mtd-mac-address = <&art 0x0>;
  73
  74         gmac-config {
  75                 device = <&gmac>;
  76                 switch-phy-addr-swap = <1>;
  77                 switch-phy-swap = <1>;
  78         };
  79 };
  80
  81 &eth1 {
  82         status = "okay";
  83         compatible = "syscon", "simple-mfd";
  84 };
  85
  86 &spi {
  87         num-chipselects = <1>;
  88         status = "okay";
  89
  90         flash@0 {
  91                 compatible = "jedec,spi-nor";
  92                 spi-max-frequency = <50000000>;
  93                 reg = <0>;
  94
  95                 partitions {
  96                         compatible = "fixed-partitions";
  97                         #address-cells = <1>;
  98                         #size-cells = <1>;
  99
 100                         uboot@0 {
 101                                 reg = <0x0 0x40000>;
 102                                 read-only;
 103                         };
 104
 105                         uboot-env@40000 {
 106                                 reg = <0x40000 0x10000>;
 107                                 read-only;
 108                         };
 109
 110                         firmware@50000 {
 111                                 compatible = "denx,uimage";
 112                                 reg = <0x50000 0xfa0000>;
 113                         };
 114
 115                         art: art@ff0000 {
 116                                 reg = <0xff0000 0x10000>;
 117                                 read-only;
 118                         };
 119                 };
 120         };
 121 };
 122
 123 &wmac {
 124         status = "okay";
 125         mtd-cal-data = <&art 0x1000>;
 126         mtd-mac-address = <&art 0x1002>;
 127 };