target/linux/ath79/dts/ar9331_alfa-network_ap121f.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9331.dtsi"
   8
   9 / {
  10         model = "ALFA Network AP121F";
  11         compatible = "alfa-network,ap121f", "qca,ar9331";
  12
  13         aliases {
  14                 label-mac-device = &wmac;
  15                 led-boot = &led_vpn;
  16                 led-failsafe = &led_vpn;
  17                 led-upgrade = &led_vpn;
  18                 serial0 = &uart;
  19         };
  20
  21         keys {
  22                 compatible = "gpio-keys";
  23
  24                 reset {
  25                         label = "reset";
  26                         linux,code = <KEY_RESTART>;
  27                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  28                 };
  29
  30                 switch {
  31                         label = "switch";
  32                         linux,code = <BTN_0>;
  33                         gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
  34                 };
  35         };
  36
  37         leds {
  38                 compatible = "gpio-leds";
  39
  40                 lan {
  41                         label = "ap121f:green:lan";
  42                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  43                 };
  44
  45                 led_vpn: vpn {
  46                         label = "ap121f:green:vpn";
  47                         gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
  48                 };
  49
  50                 wlan {
  51                         label = "ap121f:green:wlan";
  52                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  53                         linux,default-trigger = "phy0tpt";
  54                 };
  55         };
  56 };
  57
  58 &eth0 {
  59         status = "okay";
  60
  61         mtd-mac-address = <&art 0x0>;
  62
  63         gmac-config {
  64                 device = <&gmac>;
  65                 switch-phy-addr-swap = <0>;
  66                 switch-phy-swap = <0>;
  67         };
  68 };
  69
  70 &eth1 {
  71         status = "okay";
  72
  73         compatible = "syscon", "simple-mfd";
  74 };
  75
  76 &gpio {
  77         status = "okay";
  78 };
  79
  80 &spi {
  81         status = "okay";
  82
  83         num-cs = <1>;
  84
  85         flash@0 {
  86                 compatible = "jedec,spi-nor";
  87                 reg = <0>;
  88                 spi-max-frequency = <25000000>;
  89
  90                 partitions {
  91                         compatible = "fixed-partitions";
  92                         #address-cells = <1>;
  93                         #size-cells = <1>;
  94
  95                         partition@0 {
  96                                 label = "u-boot";
  97                                 reg = <0x000000 0x030000>;
  98                                 read-only;
  99                         };
 100
 101                         partition@30000 {
 102                                 label = "u-boot-env";
 103                                 reg = <0x030000 0x010000>;
 104                         };
 105
 106                         art: partition@40000 {
 107                                 label = "art";
 108                                 reg = <0x040000 0x010000>;
 109                                 read-only;
 110                         };
 111
 112                         partition@50000 {
 113                                 compatible = "denx,uimage";
 114                                 label = "firmware";
 115                                 reg = <0x050000 0xfb0000>;
 116                         };
 117                 };
 118         };
 119 };
 120
 121 &uart {
 122         status = "okay";
 123 };
 124
 125 &usb {
 126         status = "okay";
 127         dr_mode = "host";
 128 };
 129
 130 &usb_phy {
 131         status = "okay";
 132 };
 133
 134 &wmac {
 135         status = "okay";
 136
 137         mtd-cal-data = <&art 0x1000>;
 138 };