target/linux/ath79/dts/ar9330_pqi_air-pen.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9330.dtsi"
   8
   9 / {
  10         model = "PQI Air-Pen";
  11         compatible = "pqi,air-pen", "qca,ar9330";
  12
  13         aliases {
  14                 serial0 = &uart;
  15                 led-boot = &wlan;
  16                 led-failsafe = &wlan;
  17                 led-upgrade = &wlan;
  18         };
  19
  20         leds {
  21                 compatible = "gpio-leds";
  22
  23                 wlan: wlan {
  24                         label = "air-pen:blue:wlan";
  25                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  26                         linux,default-trigger = "phy0tpt";
  27                 };
  28
  29                 wps {
  30                         label = "air-pen:blue:wps";
  31                         gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
  32                 };
  33         };
  34
  35         keys {
  36                 compatible = "gpio-keys";
  37
  38                 wps {
  39                         label = "wps";
  40                         linux,code = <KEY_WPS_BUTTON>;
  41                         gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
  42                         debounce-interval = <60>;
  43                 };
  44
  45                 reset {
  46                         label = "reset";
  47                         linux,code = <KEY_RESTART>;
  48                         gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
  49                         debounce-interval = <60>;
  50                 };
  51         };
  52 };
  53
  54 &uart {
  55         status = "okay";
  56 };
  57
  58 &gpio {
  59         status = "okay";
  60 };
  61
  62 &usb {
  63         dr_mode = "host";
  64         status = "okay";
  65 };
  66
  67 &usb_phy {
  68         status = "okay";
  69 };
  70
  71 &spi {
  72         num-cs = <1>;
  73         status = "okay";
  74
  75         flash@0 {
  76                 compatible = "jedec,spi-nor";
  77                 spi-max-frequency = <104000000>;
  78                 reg = <0>;
  79
  80                 partitions {
  81                         compatible = "fixed-partitions";
  82                         #address-cells = <1>;
  83                         #size-cells = <1>;
  84
  85                         partition@0 {
  86                                 label = "u-boot";
  87                                 reg = <0x000000 0x040000>;
  88                                 read-only;
  89                         };
  90
  91                         partition@40000 {
  92                                 label = "u-boot-env";
  93                                 reg = <0x040000 0x010000>;
  94                         };
  95
  96                         art: partition@50000 {
  97                                 label = "art";
  98                                 reg = <0x050000 0x010000>;
  99                                 read-only;
 100                         };
 101
 102                         partition@60000 {
 103                                 label = "NVRAM";
 104                                 reg = <0x060000 0x010000>;
 105                                 read-only;
 106                         };
 107
 108                         partition@70000 {
 109                                 compatible = "denx,uimage";
 110                                 label = "firmware";
 111                                 reg = <0x070000 0x780000>;
 112                         };
 113
 114                         partition@7f0000 {
 115                                 label = "CONF";
 116                                 reg = <0x7f0000 0x010000>;
 117                                 read-only;
 118                         };
 119                 };
 120         };
 121 };
 122
 123 &eth0 {
 124         status = "okay";
 125
 126         mtd-mac-address = <&art 0x1002>;
 127
 128         gmac-config {
 129                 device = <&gmac>;
 130
 131                 switch-phy-addr-swap = <0>;
 132                 switch-phy-swap = <0>;
 133         };
 134 };
 135
 136 &eth1 {
 137         status = "okay";
 138         compatible = "syscon", "simple-mfd";
 139 };
 140
 141 &wmac {
 142         status = "okay";
 143         mtd-cal-data = <&art 0x1000>;
 144         mtd-mac-address = <&art 0x2>;
 145 };