target/linux/ath79/dts/ar9330_pqi_air-pen.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9330.dtsi"
   8
   9 / {
  10         model = "PQI Air-Pen";
  11         compatible = "pqi,air-pen", "qca,ar9330";
  12
  13         aliases {
  14                 serial0 = &uart;
  15                 led-boot = &led_wlan;
  16                 led-failsafe = &led_wlan;
  17                 led-upgrade = &led_wlan;
  18         };
  19
  20         leds {
  21                 compatible = "gpio-leds";
  22
  23                 led_wlan: wlan {
  24                         label = "air-pen:blue:wlan";
  25                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  26                         linux,default-trigger = "phy0tpt";
  27                 };
  28
  29                 wps {
  30                         label = "air-pen:blue:wps";
  31                         gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
  32                 };
  33         };
  34
  35         keys {
  36                 compatible = "gpio-keys";
  37
  38                 wps {
  39                         label = "wps";
  40                         linux,code = <KEY_WPS_BUTTON>;
  41                         gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
  42                         debounce-interval = <60>;
  43                 };
  44
  45                 reset {
  46                         label = "reset";
  47                         linux,code = <KEY_RESTART>;
  48                         gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
  49                         debounce-interval = <60>;
  50                 };
  51         };
  52 };
  53
  54 &uart {
  55         status = "okay";
  56 };
  57
  58 &gpio {
  59         status = "okay";
  60 };
  61
  62 &usb {
  63         dr_mode = "host";
  64         status = "okay";
  65 };
  66
  67 &usb_phy {
  68         status = "okay";
  69 };
  70
  71 &spi {
  72         status = "okay";
  73
  74         num-cs = <1>;
  75
  76         flash@0 {
  77                 compatible = "jedec,spi-nor";
  78                 spi-max-frequency = <50000000>;
  79                 reg = <0>;
  80
  81                 partitions {
  82                         compatible = "fixed-partitions";
  83                         #address-cells = <1>;
  84                         #size-cells = <1>;
  85
  86                         partition@0 {
  87                                 label = "u-boot";
  88                                 reg = <0x000000 0x040000>;
  89                                 read-only;
  90                         };
  91
  92                         partition@40000 {
  93                                 label = "u-boot-env";
  94                                 reg = <0x040000 0x010000>;
  95                         };
  96
  97                         art: partition@50000 {
  98                                 label = "art";
  99                                 reg = <0x050000 0x010000>;
 100                                 read-only;
 101                         };
 102
 103                         partition@60000 {
 104                                 label = "NVRAM";
 105                                 reg = <0x060000 0x010000>;
 106                                 read-only;
 107                         };
 108
 109                         partition@70000 {
 110                                 compatible = "denx,uimage";
 111                                 label = "firmware";
 112                                 reg = <0x070000 0x780000>;
 113                         };
 114
 115                         partition@7f0000 {
 116                                 label = "CONF";
 117                                 reg = <0x7f0000 0x010000>;
 118                                 read-only;
 119                         };
 120                 };
 121         };
 122 };
 123
 124 &eth0 {
 125         status = "okay";
 126
 127         mtd-mac-address = <&art 0x1002>;
 128
 129         gmac-config {
 130                 device = <&gmac>;
 131
 132                 switch-phy-addr-swap = <0>;
 133                 switch-phy-swap = <0>;
 134         };
 135 };
 136
 137 &eth1 {
 138         status = "okay";
 139
 140         compatible = "syscon", "simple-mfd";
 141 };
 142
 143 &wmac {
 144         status = "okay";
 145
 146         mtd-cal-data = <&art 0x1000>;
 147         mtd-mac-address = <&art 0x2>;
 148 };