target/linux/ath79/dts/ar7242_avm_fritz300e.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar7242.dtsi"
   8
   9 / {
  10         compatible = "avm,fritz300e", "qca,ar7242";
  11         model = "AVM FRITZ!WLAN Repeater 300E";
  12
  13         aliases {
  14                 led-boot = &led_power;
  15                 led-failsafe = &led_power;
  16                 led-running = &led_power;
  17                 led-upgrade = &led_power;
  18                 label-mac-device = &ath9k;
  19         };
  20
  21         keys {
  22                 compatible = "gpio-keys";
  23
  24                 wps {
  25                         label = "wps";
  26                         linux,code = <KEY_WPS_BUTTON>;
  27                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  28                         debounce-interval = <60>;
  29                 };
  30         };
  31
  32         leds {
  33                 compatible = "gpio-leds";
  34
  35                 led_power: power {
  36                         label = "fritz300e:green:power";
  37                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  38                         default-state = "on";
  39                 };
  40
  41                 lan {
  42                         label = "fritz300e:green:lan";
  43                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  44                 };
  45
  46                 wlan {
  47                         label = "fritz300e:green:wlan";
  48                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  49                         linux,default-trigger = "phy0tpt";
  50                 };
  51         };
  52
  53         ath9k-leds {
  54                 compatible = "gpio-leds";
  55
  56                 rssi0 {
  57                         label = "fritz300e:green:rssi0";
  58                         gpios = <&ath9k 10 GPIO_ACTIVE_LOW>;
  59                 };
  60
  61                 rssi1 {
  62                         label = "fritz300e:green:rssi1";
  63                         gpios = <&ath9k 4 GPIO_ACTIVE_LOW>;
  64                 };
  65
  66                 rssi2 {
  67                         label = "fritz300e:green:rssi2";
  68                         gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
  69                 };
  70
  71                 rssi3 {
  72                         label = "fritz300e:green:rssi3";
  73                         gpios = <&ath9k 7 GPIO_ACTIVE_LOW>;
  74                 };
  75
  76                 rssi4 {
  77                         label = "fritz300e:green:rssi4";
  78                         gpios = <&ath9k 5 GPIO_ACTIVE_LOW>;
  79                 };
  80         };
  81
  82         eth-phy-reset {
  83                 compatible = "regulator-fixed";
  84
  85                 regulator-name = "eth-phy-reset";
  86                 regulator-min-microvolt = <3300000>;
  87                 regulator-max-microvolt = <3300000>;
  88
  89                 gpio = <&gpio 11 GPIO_ACTIVE_LOW>;
  90                 startup-delay-us = <300000>;
  91                 enable-active-high;
  92
  93                 regulator-always-on;
  94         };
  95 };
  96
  97 &spi {
  98         status = "okay";
  99
 100         num-cs = <1>;
 101
 102         flash@0 {
 103                 compatible = "jedec,spi-nor";
 104                 reg = <0>;
 105                 spi-max-frequency = <25000000>;
 106
 107                 partitions {
 108                         compatible = "fixed-partitions";
 109                         #address-cells = <1>;
 110                         #size-cells = <1>;
 111
 112                         partition@0 {
 113                                 reg = <0x0 0x20000>;
 114                                 label = "urloader";
 115                                 read-only;
 116                         };
 117
 118                         partition@20000 {
 119                                 compatible = "avm,eva-firmware";
 120                                 reg = <0x20000 0xee0000>;
 121                                 label = "firmware";
 122                         };
 123
 124                         partition@f00000 {
 125                                 reg = <0xf00000 0x80000>;
 126                                 label = "tffs (1)";
 127                                 read-only;
 128                         };
 129
 130                         partition@f80000 {
 131                                 reg = <0xf80000 0x80000>;
 132                                 label = "tffs (2)";
 133                                 read-only;
 134                         };
 135                 };
 136         };
 137 };
 138
 139 &uart {
 140         status = "okay";
 141 };
 142
 143 &pcie {
 144         status = "okay";
 145
 146         ath9k: wifi@0,0 {
 147                 reg = <0x0000 0 0 0 0>;
 148                 #gpio-cells = <2>;
 149                 gpio-controller;
 150                 qca,no-eeprom;
 151         };
 152 };
 153
 154 &mdio0 {
 155         status = "okay";
 156
 157         phy0: ethernet-phy@0 {
 158                 reg = <0>;
 159                 phy-mode = "rgmii";
 160         };
 161 };
 162
 163 &eth0 {
 164         status = "okay";
 165
 166         phy-mode = "rgmii";
 167         phy-handle = <&phy0>;
 168
 169         pll-data = <0x16000000 0x00000101 0x00001313>;
 170 };