target/linux/ath79/dts/ar7241_ubnt_xm.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "ar7241.dtsi"
   7
   8 / {
   9         compatible = "ubnt,xm", "qca,ar7241";
  10         model = "Ubiquiti Networks XM (rev 1.0) board";
  11
  12         memory@0 {
  13                 device_type = "memory";
  14                 reg = <0x0 0x2000000>;
  15         };
  16
  17 /*      extosc: ref {
  18                 compatible = "fixed-clock";
  19                 #clock-cells = <0>;
  20                 clock-frequency = <40000000>;
  21         };
  22 */
  23         keys {
  24                 compatible = "gpio-keys-polled";
  25                 #address-cells = <1>;
  26                 #size-cells = <0>;
  27
  28                 poll-interval = <20>;
  29                 reset {
  30                         linux,code = <KEY_RESTART>;
  31                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  32                         debounce-interval = <60>;
  33                 };
  34         };
  35
  36         leds {
  37                 compatible = "gpio-leds";
  38                 link1 {
  39                         label = "ubnt:red:link1";
  40                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  41                 };
  42
  43                 link2 {
  44                         label = "ubnt:orange:link2";
  45                         gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
  46                 };
  47
  48                 link3 {
  49                         label = "ubnt:green:link3";
  50                         gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
  51                 };
  52
  53                 link4 {
  54                         label = "ubnt:green:link4";
  55                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  56                 };
  57         };
  58 };
  59
  60 &uart {
  61         status = "okay";
  62 };
  63
  64 /*&pll {
  65         clocks = <&extosc>;
  66 };*/
  67
  68 &spi {
  69         status = "okay";
  70         num-cs = <1>;
  71
  72         flash@0 {
  73                 #address-cells = <1>;
  74                 #size-cells = <1>;
  75                 compatible = "mx25l6405d";
  76                 reg = <0>;
  77                 spi-max-frequency = <25000000>;
  78
  79                 partitions {
  80                         compatible = "fixed-partitions";
  81                         #address-cells = <1>;
  82                         #size-cells = <1>;
  83
  84                         partition@0 {
  85                                 label = "u-boot";
  86                                 reg = <0x000000 0x040000>;
  87                                 read-only;
  88                         };
  89
  90                         partition@1 {
  91                                 label = "u-boot-env";
  92                                 reg = <0x040000 0x010000>;
  93                         };
  94
  95                         partition@2 {
  96                                 label = "firmware";
  97                                 reg = <0x050000 0x750000>;
  98                         };
  99
 100                         partition@3 {
 101                                 label = "board_config";
 102                                 reg = <0x7a0000 0x010000>;
 103                                 read-only;
 104                         };
 105
 106                         partition@4 {
 107                                 label = "cfg";
 108                                 reg = <0x7b0000 0x040000>;
 109                                 read-only;
 110                         };
 111
 112                         art: partition@5 {
 113                                 label = "art";
 114                                 reg = <0x7f0000 0x010000>;
 115                                 read-only;
 116                         };
 117                 };
 118         };
 119 };
 120
 121 &pcie {
 122         status = "okay";
 123
 124         ath9k@0 {
 125                 reg = <0x0000 0 0 0 0>;
 126                 qca,no-eeprom;
 127         };
 128 };
 129
 130 &mdio0 {
 131         status = "okay";
 132
 133         phy4: ethernet-phy@4 {
 134                 reg = <4>;
 135                 phy-mode = "mii";
 136         };
 137 };
 138
 139 &eth0 {
 140         status = "okay";
 141
 142         mtd-mac-address = <&art 0x0>;
 143
 144         phy-mode = "mii";
 145         phy-handle = <&phy4>;
 146 };
 147
 148 &eth1 {
 149         status = "okay";
 150
 151         mtd-mac-address = <&art 0x6>;
 152 };