target/linux/ath79/dts/ar7241_ubnt-xm.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "ar7241.dtsi"
   7
   8 / {
   9         compatible = "ubnt,xm", "qca,ar7241";
  10         model = "Ubiquiti Networks XM (rev 1.0) board";
  11
  12         memory@0 {
  13                 device_type = "memory";
  14                 reg = <0x0 0x2000000>;
  15         };
  16
  17 /*      extosc: ref {
  18                 compatible = "fixed-clock";
  19                 #clock-cells = <0>;
  20                 clock-frequency = <40000000>;
  21         };
  22 */
  23         keys {
  24                 compatible = "gpio-keys-polled";
  25                 #address-cells = <1>;
  26                 #size-cells = <0>;
  27
  28                 poll-interval = <20>;
  29                 button@0 {
  30                         label = "reset";
  31                         linux,code = <KEY_RESTART>;
  32                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  33                         debounce-interval = <60>;
  34                 };
  35         };
  36
  37         leds {
  38                 compatible = "gpio-leds";
  39                 led@0 {
  40                         label = "ubnt:red:link1";
  41                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  42                 };
  43
  44                 led@1 {
  45                         label = "ubnt:orange:link2";
  46                         gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
  47                 };
  48
  49                 led@2 {
  50                         label = "ubnt:green:link3";
  51                         gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
  52                 };
  53
  54                 led@3 {
  55                         label = "ubnt:green:link4";
  56                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  57                 };
  58         };
  59 };
  60
  61 &uart {
  62         status = "okay";
  63 };
  64
  65 /*&pll {
  66         clocks = <&extosc>;
  67 };*/
  68
  69 &spi {
  70         status = "okay";
  71         num-cs = <1>;
  72
  73         flash@0 {
  74                 #address-cells = <1>;
  75                 #size-cells = <1>;
  76                 compatible = "mx25l6405d";
  77                 reg = <0>;
  78                 spi-max-frequency = <25000000>;
  79
  80                 partition@0 {
  81                         label = "u-boot";
  82                         reg = <0x000000 0x040000>;
  83                 };
  84
  85                 partition@1 {
  86                         label = "u-boot-env";
  87                         reg = <0x040000 0x010000>;
  88                 };
  89
  90                 partition@2 {
  91                         label = "firmware";
  92                         reg = <0x050000 0x750000>;
  93                 };
  94
  95                 partition@3 {
  96                         label = "board_config";
  97                         reg = <0x7a0000 0x010000>;
  98                         read-only;
  99                 };
 100
 101                 partition@4 {
 102                         label = "cfg";
 103                         reg = <0x7b0000 0x040000>;
 104                         read-only;
 105                 };
 106
 107                 art: partition@5 {
 108                         label = "art";
 109                         reg = <0x7f0000 0x010000>;
 110                         read-only;
 111                 };
 112         };
 113 };
 114
 115 &pcie {
 116         status = "okay";
 117
 118         ath9k@0000 {
 119                 reg = <0x0000 0 0 0 0>;
 120                 qca,no-eeprom;
 121         };
 122 };
 123
 124 &mdio0 {
 125         status = "okay";
 126
 127         phy4: ethernet-phy@4 {
 128                 reg = <4>;
 129                 phy-mode = "mii";
 130         };
 131 };
 132
 133 &eth0 {
 134         status = "okay";
 135
 136         mtd-mac-address = <&art 0x0>;
 137
 138         phy-mode = "mii";
 139         phy-handle = <&phy4>;
 140 };
 141
 142 &eth1 {
 143         status = "okay";
 144
 145         mtd-mac-address = <&art 0x6>;
 146 };