target/linux/ath79/dts/ar7161_netgear_wndr3800.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar7100.dtsi"
   8
   9 / {
  10         compatible = "netgear,wndr3800", "qca,ar7161";
  11         model = "Netgear WNDR3800";
  12
  13         aliases {
  14                 led-status = &power_green;
  15         };
  16
  17         chosen {
  18                 bootargs = "console=ttyS0,115200";
  19         };
  20
  21         memory@0 {
  22                 device_type = "memory";
  23                 reg = <0x0 0x8000000>;
  24         };
  25
  26         extosc: ref {
  27                 compatible = "fixed-clock";
  28                 #clock-cells = <0>;
  29                 clock-output-names = "ref";
  30                 clock-frequency = <40000000>;
  31         };
  32
  33         reset-leds {
  34                 compatible = "reset-leds";
  35
  36                 usb_led {
  37                         label = "netgear:green:usb";
  38                         resets = <&rst 12>;
  39                         trigger-sources = <&usb_ochi_port>, <&usb_echi_port>;
  40                         linux,default-trigger = "usbport";
  41                 };
  42         };
  43
  44         gpio-leds {
  45                 compatible = "gpio-leds";
  46
  47                 wps {
  48                         label = "netgear:orange:wps";
  49                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  50                         default-state = "off";
  51                 };
  52
  53                 power_green: power_green {
  54                         label = "netgear:green:power";
  55                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  56                         default-state = "off";
  57                 };
  58
  59                 power_orange {
  60                         label = "netgear:orange:power";
  61                         gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
  62                         default-state = "off";
  63                 };
  64
  65                 wps_green {
  66                         label = "netgear:green:wps";
  67                         gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
  68                         default-state = "off";
  69                 };
  70
  71                 wan_green {
  72                         label = "netgear:green:wan";
  73                         gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
  74                         default-state = "off";
  75                 };
  76         };
  77
  78         gpio-keys-polled {
  79                 compatible = "gpio-keys-polled";
  80                 #address-cells = <1>;
  81                 #size-cells = <0>;
  82                 poll-interval = <100>;
  83
  84                 wps {
  85                         label = "wps";
  86                         linux,code = <KEY_WPS_BUTTON>;
  87                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  88                 };
  89
  90                 reset {
  91                         label = "reset";
  92                         linux,code = <KEY_RESTART>;
  93                         gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
  94                 };
  95
  96                 rfkill {
  97                         label = "rfkill";
  98                         linux,code = <KEY_RFKILL>;
  99                         gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
 100                 };
 101         };
 102
 103         rtl8366s {
 104                 compatible = "realtek,rtl8366s";
 105                 gpio-sda = <&gpio 5 GPIO_ACTIVE_HIGH>;
 106                 gpio-sck = <&gpio 7 GPIO_ACTIVE_HIGH>;
 107
 108                 mdio-bus {
 109                         status = "okay";
 110
 111                         phy-mask = <0x10>;
 112
 113                         phy4: ethernet-phy@4 {
 114                                 reg = <4>;
 115                                 phy-mode = "rgmii";
 116                         };
 117                 };
 118         };
 119 };
 120
 121 &usb_phy {
 122         status = "okay";
 123 };
 124
 125 &usb1 {
 126         status = "okay";
 127
 128         usb_ochi_port: port@1 {
 129                 reg = <1>;
 130                 #trigger-source-cells = <0>;
 131         };
 132 };
 133
 134 &usb2 {
 135         status = "okay";
 136
 137         usb_echi_port: port@1 {
 138                 reg = <1>;
 139                 #trigger-source-cells = <0>;
 140         };
 141 };
 142
 143 &pcie0 {
 144         status = "okay";
 145 };
 146
 147 &uart {
 148         status = "okay";
 149 };
 150
 151 &spi {
 152         status = "okay";
 153         num-cs = <1>;
 154
 155         flash@0 {
 156                 #address-cells = <1>;
 157                 #size-cells = <1>;
 158                 compatible = "mx25l12805d";
 159                 reg = <0>;
 160                 spi-max-frequency = <25000000>;
 161
 162                 partitions {
 163                         compatible = "fixed-partitions";
 164                         #address-cells = <1>;
 165                         #size-cells = <1>;
 166
 167                         partition@0 {
 168                                 label = "u-boot";
 169                                 reg = <0x000000 0x050000>;
 170                                 read-only;
 171                         };
 172
 173                         partition@1 {
 174                                 label = "u-boot-env";
 175                                 reg = <0x050000 0x020000>;
 176                                 read-only;
 177                         };
 178
 179                         partition@2 {
 180                                 label = "firmware";
 181                                 reg = <0x070000 0xf80000>;
 182                         };
 183
 184                         art: partition@3 {
 185                                 label = "art";
 186                                 reg = <0xff0000 0x010000>;
 187                                 read-only;
 188                         };
 189                 };
 190         };
 191 };
 192
 193 &eth0 {
 194         status = "okay";
 195
 196         pll-data = <0x11110000 0x00001099 0x00991099>;
 197
 198         mtd-mac-address = <&art 0x00>;
 199
 200         fixed-link {
 201                 speed = <1000>;
 202                 full-duplex;
 203         };
 204 };
 205
 206 &eth1 {
 207         status = "okay";
 208
 209         pll-data = <0x11110000 0x00001099 0x00991099>;
 210
 211         mtd-mac-address = <&art 0x06>;
 212
 213         resets = <&rst 13>;
 214         reset-names = "mac";
 215
 216         phy-handle = <&phy4>;
 217 };