1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * (C) Copyright 2012 Michal Simek <monstr@monstr.eu>
4 * (C) Copyright 2013 - 2018 Xilinx, Inc.
6 * Common configuration options for all Zynq boards.
9 #ifndef __CONFIG_ZYNQ_COMMON_H
10 #define __CONFIG_ZYNQ_COMMON_H
13 #ifndef CONFIG_CPU_FREQ_HZ
14 # define CONFIG_CPU_FREQ_HZ 800000000
17 #define CONFIG_REMAKE_ELF
20 #define CONFIG_SYS_L2CACHE_OFF
21 #ifndef CONFIG_SYS_L2CACHE_OFF
22 # define CONFIG_SYS_L2_PL310
23 # define CONFIG_SYS_PL310_BASE 0xf8f02000
26 #define ZYNQ_SCUTIMER_BASEADDR 0xF8F00600
27 #define CONFIG_SYS_TIMERBASE ZYNQ_SCUTIMER_BASEADDR
28 #define CONFIG_SYS_TIMER_COUNTS_DOWN
29 #define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4)
32 /* The following table includes the supported baudrates */
33 #define CONFIG_SYS_BAUDRATE_TABLE \
34 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
36 #define CONFIG_ARM_DCC
39 #if defined(CONFIG_ZYNQ_GEM)
40 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
41 # define CONFIG_BOOTP_MAY_FAIL
45 #ifdef CONFIG_ZYNQ_QSPI
46 # define CONFIG_SF_DEFAULT_SPEED 30000000
50 #ifdef CONFIG_MTD_NOR_FLASH
51 # define CONFIG_SYS_FLASH_BASE 0xE2000000
52 # define CONFIG_SYS_FLASH_SIZE (16 * 1024 * 1024)
53 # define CONFIG_SYS_MAX_FLASH_BANKS 1
54 # define CONFIG_SYS_MAX_FLASH_SECT 512
55 # define CONFIG_SYS_FLASH_ERASE_TOUT 1000
56 # define CONFIG_SYS_FLASH_WRITE_TOUT 5000
57 # define CONFIG_FLASH_SHOW_PROGRESS 10
58 # undef CONFIG_SYS_FLASH_EMPTY_INFO
61 #ifdef CONFIG_NAND_ZYNQ
62 #define CONFIG_SYS_MAX_NAND_DEVICE 1
63 #define CONFIG_SYS_NAND_ONFI_DETECTION
66 #ifdef CONFIG_USB_EHCI_ZYNQ
67 # define CONFIG_EHCI_IS_TDI
69 # define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x600000
70 # define DFU_DEFAULT_POLL_TIMEOUT 300
71 # define CONFIG_USB_CABLE_CHECK
72 # define CONFIG_THOR_RESET_OFF
73 # define DFU_ALT_INFO_RAM \
76 "${kernel_image} ram 0x3000000 0x500000\\\\;" \
77 "${devicetree_image} ram 0x2A00000 0x20000\\\\;" \
78 "${ramdisk_image} ram 0x2000000 0x600000\0" \
79 "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
80 "thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
82 # if defined(CONFIG_MMC_SDHCI_ZYNQ)
83 # define DFU_ALT_INFO_MMC \
86 "${kernel_image} fat 0 1\\\\;" \
87 "${devicetree_image} fat 0 1\\\\;" \
88 "${ramdisk_image} fat 0 1\0" \
89 "dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \
90 "thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0"
92 # define DFU_ALT_INFO \
96 # define DFU_ALT_INFO \
101 #if !defined(DFU_ALT_INFO)
102 # define DFU_ALT_INFO
106 #if defined(CONFIG_SYS_I2C_ZYNQ)
107 # define CONFIG_SYS_I2C
111 #ifdef CONFIG_ZYNQ_EEPROM
112 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
113 # define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
114 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
115 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
116 # define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */
119 /* Allow to overwrite serial and ethaddr */
120 #define CONFIG_ENV_OVERWRITE
122 /* enable preboot to be loaded before CONFIG_BOOTDELAY */
123 #define CONFIG_PREBOOT
125 /* Boot configuration */
126 #define CONFIG_SYS_LOAD_ADDR 0 /* default? */
128 #ifdef CONFIG_SPL_BUILD
132 #ifdef CONFIG_CMD_MMC
133 #define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
135 #define BOOT_TARGET_DEVICES_MMC(func)
138 #ifdef CONFIG_CMD_USB
139 #define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
141 #define BOOT_TARGET_DEVICES_USB(func)
144 #if defined(CONFIG_CMD_PXE) && defined(CONFIG_CMD_DHCP)
145 #define BOOT_TARGET_DEVICES_PXE(func) func(PXE, pxe, na)
147 #define BOOT_TARGET_DEVICES_PXE(func)
150 #if defined(CONFIG_CMD_DHCP)
151 #define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
153 #define BOOT_TARGET_DEVICES_DHCP(func)
156 #define BOOT_TARGET_DEVICES(func) \
157 BOOT_TARGET_DEVICES_MMC(func) \
158 BOOT_TARGET_DEVICES_USB(func) \
159 BOOT_TARGET_DEVICES_PXE(func) \
160 BOOT_TARGET_DEVICES_DHCP(func)
162 #include <config_distro_bootcmd.h>
163 #endif /* CONFIG_SPL_BUILD */
165 /* Default environment */
166 #ifndef CONFIG_EXTRA_ENV_SETTINGS
167 #define CONFIG_EXTRA_ENV_SETTINGS \
168 "fit_image=fit.itb\0" \
169 "load_addr=0x2000000\0" \
170 "fit_size=0x800000\0" \
171 "flash_off=0x100000\0" \
172 "nor_flash_off=0xE2100000\0" \
173 "fdt_high=0x20000000\0" \
174 "initrd_high=0x20000000\0" \
175 "loadbootenv_addr=0x2000000\0" \
176 "fdt_addr_r=0x1f00000\0" \
177 "pxefile_addr_r=0x2000000\0" \
178 "kernel_addr_r=0x2000000\0" \
179 "scriptaddr=0x3000000\0" \
180 "ramdisk_addr_r=0x3100000\0" \
181 "bootenv=uEnv.txt\0" \
182 "bootenv_dev=mmc\0" \
183 "loadbootenv=load ${bootenv_dev} 0 ${loadbootenv_addr} ${bootenv}\0" \
184 "importbootenv=echo Importing environment from ${bootenv_dev} ...; " \
185 "env import -t ${loadbootenv_addr} $filesize\0" \
186 "bootenv_existence_test=test -e ${bootenv_dev} 0 /${bootenv}\0" \
187 "setbootenv=if env run bootenv_existence_test; then " \
188 "if env run loadbootenv; then " \
189 "env run importbootenv; " \
192 "sd_loadbootenv=set bootenv_dev mmc && " \
193 "run setbootenv \0" \
194 "usb_loadbootenv=set bootenv_dev usb && usb start && run setbootenv \0" \
195 "preboot=if test $modeboot = sdboot; then " \
196 "run sd_loadbootenv; " \
197 "echo Checking if uenvcmd is set ...; " \
198 "if test -n $uenvcmd; then " \
199 "echo Running uenvcmd ...; " \
203 "norboot=echo Copying FIT from NOR flash to RAM... && " \
204 "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
205 "bootm ${load_addr}\0" \
206 "sdboot=echo Copying FIT from SD to RAM... && " \
207 "load mmc 0 ${load_addr} ${fit_image} && " \
208 "bootm ${load_addr}\0" \
209 "jtagboot=echo TFTPing FIT to RAM... && " \
210 "tftpboot ${load_addr} ${fit_image} && " \
211 "bootm ${load_addr}\0" \
212 "usbboot=if usb start; then " \
213 "echo Copying FIT from USB to RAM... && " \
214 "load usb 0 ${load_addr} ${fit_image} && " \
215 "bootm ${load_addr}; fi\0" \
220 /* Miscellaneous configurable options */
222 #define CONFIG_CLOCKS
223 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */
225 #define CONFIG_SYS_MEMTEST_START 0
226 #define CONFIG_SYS_MEMTEST_END 0x1000
228 #define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
229 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000
230 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
231 CONFIG_SYS_INIT_RAM_SIZE - \
232 GENERATED_GBL_DATA_SIZE)
235 /* Extend size of kernel image for uncompression */
236 #define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024)
238 /* Boot FreeBSD/vxWorks from an ELF image */
239 #define CONFIG_SYS_MMC_MAX_DEVICE 1
241 #define CONFIG_SYS_LDSCRIPT "arch/arm/mach-zynq/u-boot.lds"
244 #ifdef CONFIG_MMC_SDHCI_ZYNQ
245 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
246 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
249 /* Disable dcache for SPL just for sure */
250 #ifdef CONFIG_SPL_BUILD
251 #define CONFIG_SYS_DCACHE_OFF
254 /* Address in RAM where the parameters must be copied by SPL. */
255 #define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000
257 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "system.dtb"
258 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
260 /* Not using MMC raw mode - just for compilation purpose */
261 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0
262 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0
263 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0
265 /* qspi mode is working fine */
266 #ifdef CONFIG_ZYNQ_QSPI
267 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000
268 #define CONFIG_SYS_SPI_ARGS_OFFS 0x200000
269 #define CONFIG_SYS_SPI_ARGS_SIZE 0x80000
270 #define CONFIG_SYS_SPI_KERNEL_OFFS (CONFIG_SYS_SPI_ARGS_OFFS + \
271 CONFIG_SYS_SPI_ARGS_SIZE)
274 /* SP location before relocation, must use scratch RAM */
275 #define CONFIG_SPL_TEXT_BASE 0x0
277 /* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
278 #define CONFIG_SPL_MAX_SIZE 0x30000
280 /* On the top of OCM space */
281 #define CONFIG_SYS_SPL_MALLOC_START CONFIG_SPL_STACK_R_ADDR
282 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x2000000
285 * SPL stack position - and stack goes down
286 * 0xfffffe00 is used for putting wfi loop.
287 * Set it up as limit for now.
289 #define CONFIG_SPL_STACK 0xfffffe00
292 #define CONFIG_SPL_BSS_START_ADDR 0x100000
293 #define CONFIG_SPL_BSS_MAX_SIZE 0x100000
295 #define CONFIG_SPL_LOAD_FIT_ADDRESS 0x10000000
297 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
299 #endif /* __CONFIG_ZYNQ_COMMON_H */