1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright (C) 2012 Altera Corporation <www.altera.com>
5 #ifndef __CONFIG_SOCFPGA_COMMON_H__
6 #define __CONFIG_SOCFPGA_COMMON_H__
9 * High level configuration
13 #define CONFIG_SYS_BOOTMAPSZ (64 * 1024 * 1024)
15 #define CONFIG_TIMESTAMP /* Print image info with timestamp */
17 /* add target to build it automatically upon "make" */
18 #define CONFIG_BUILD_TARGET "u-boot-with-spl.sfp"
21 * Memory configurations
23 #define CONFIG_NR_DRAM_BANKS 1
24 #define PHYS_SDRAM_1 0x0
25 #define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024)
26 #define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
27 #define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE
28 #if defined(CONFIG_TARGET_SOCFPGA_GEN5)
29 #define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
30 #define CONFIG_SYS_INIT_RAM_SIZE 0x10000
31 #elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
32 #define CONFIG_SYS_INIT_RAM_ADDR 0xFFE00000
33 #define CONFIG_SYS_INIT_RAM_SIZE 0x40000 /* 256KB */
35 #define CONFIG_SYS_INIT_SP_ADDR \
36 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
38 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
41 * U-Boot general configurations
43 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
44 /* Print buffer size */
45 #define CONFIG_SYS_MAXARGS 32 /* Max number of command args */
46 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
47 /* Boot argument buffer size */
49 #ifndef CONFIG_SYS_HOSTNAME
50 #define CONFIG_SYS_HOSTNAME CONFIG_SYS_BOARD
56 #define CONFIG_SYS_L2_PL310
57 #define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS
60 * EPCS/EPCQx1 Serial Flash Controller
62 #ifdef CONFIG_ALTERA_SPI
63 #define CONFIG_SF_DEFAULT_SPEED 30000000
65 * The base address is configurable in QSys, each board must specify the
66 * base address based on it's particular FPGA configuration. Please note
67 * that the address here is incremented by 0x400 from the Base address
68 * selected in QSys, since the SPI registers are at offset +0x400.
69 * #define CONFIG_SYS_SPI_BASE 0xff240400
74 * Ethernet on SoC (EMAC)
77 #define CONFIG_DW_ALTDESCRIPTOR
84 #ifdef CONFIG_CMD_FPGA
85 #define CONFIG_FPGA_COUNT 1
91 /* This timer uses eosc1, whose clock frequency is fixed at any condition. */
92 #define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS
93 #define CONFIG_SYS_TIMER_COUNTS_DOWN
94 #define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4)
95 #define CONFIG_SYS_TIMER_RATE 25000000
100 #ifdef CONFIG_HW_WATCHDOG
101 #define CONFIG_DESIGNWARE_WATCHDOG
102 #define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS
103 #define CONFIG_DW_WDT_CLOCK_KHZ 25000
104 #define CONFIG_WATCHDOG_TIMEOUT_MSECS 30000
110 #ifdef CONFIG_CMD_MMC
111 #define CONFIG_BOUNCE_BUFFER
113 /* using smaller max blk cnt to avoid flooding the limited stack we have */
114 #define CONFIG_SYS_MMC_MAX_BLK_COUNT 256 /* FIXME -- SPL only? */
120 #ifdef CONFIG_NAND_DENALI
121 #define CONFIG_SYS_MAX_NAND_DEVICE 1
122 #define CONFIG_SYS_NAND_ONFI_DETECTION
123 #define CONFIG_SYS_NAND_REGS_BASE SOCFPGA_NANDREGS_ADDRESS
124 #define CONFIG_SYS_NAND_DATA_BASE SOCFPGA_NANDDATA_ADDRESS
130 #ifndef CONFIG_DM_I2C
131 #define CONFIG_SYS_I2C
132 #define CONFIG_SYS_I2C_BASE SOCFPGA_I2C0_ADDRESS
133 #define CONFIG_SYS_I2C_BASE1 SOCFPGA_I2C1_ADDRESS
134 #define CONFIG_SYS_I2C_BASE2 SOCFPGA_I2C2_ADDRESS
135 #define CONFIG_SYS_I2C_BASE3 SOCFPGA_I2C3_ADDRESS
136 /* Using standard mode which the speed up to 100Kb/s */
137 #define CONFIG_SYS_I2C_SPEED 100000
138 #define CONFIG_SYS_I2C_SPEED1 100000
139 #define CONFIG_SYS_I2C_SPEED2 100000
140 #define CONFIG_SYS_I2C_SPEED3 100000
141 /* Address of device when used as slave */
142 #define CONFIG_SYS_I2C_SLAVE 0x02
143 #define CONFIG_SYS_I2C_SLAVE1 0x02
144 #define CONFIG_SYS_I2C_SLAVE2 0x02
145 #define CONFIG_SYS_I2C_SLAVE3 0x02
147 /* Clock supplied to I2C controller in unit of MHz */
148 unsigned int cm_get_l4_sp_clk_hz(void);
149 #define IC_CLK (cm_get_l4_sp_clk_hz() / 1000000)
151 #endif /* CONFIG_DM_I2C */
156 /* Enable multiple SPI NOR flash manufacturers */
157 #ifndef CONFIG_SPL_BUILD
158 #define CONFIG_SPI_FLASH_MTD
159 #define CONFIG_MTD_DEVICE
160 #define CONFIG_MTD_PARTITIONS
162 /* QSPI reference clock */
164 unsigned int cm_get_qspi_controller_clk_hz(void);
165 #define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()
169 * Designware SPI support
175 #define CONFIG_SYS_NS16550_SERIAL
182 * USB Gadget (DFU, UMS)
184 #if defined(CONFIG_CMD_DFU) || defined(CONFIG_CMD_USB_MASS_STORAGE)
185 #define CONFIG_SYS_DFU_DATA_BUF_SIZE (16 * 1024 * 1024)
186 #define DFU_DEFAULT_POLL_TIMEOUT 300
189 #define CONFIG_G_DNL_UMS_VENDOR_NUM 0x0525
190 #define CONFIG_G_DNL_UMS_PRODUCT_NUM 0xA4A5
196 #if !defined(CONFIG_ENV_SIZE)
197 #define CONFIG_ENV_SIZE (8 * 1024)
200 /* Environment for SDMMC boot */
201 #if defined(CONFIG_ENV_IS_IN_MMC) && !defined(CONFIG_ENV_OFFSET)
202 #define CONFIG_SYS_MMC_ENV_DEV 0 /* device 0 */
203 #define CONFIG_ENV_OFFSET (34 * 512) /* just after the GPT */
206 /* Environment for QSPI boot */
207 #if defined(CONFIG_ENV_IS_IN_SPI_FLASH) && !defined(CONFIG_ENV_OFFSET)
208 #define CONFIG_ENV_OFFSET 0x00100000
209 #define CONFIG_ENV_SECT_SIZE (64 * 1024)
213 * mtd partitioning for serial NOR flash
215 * device nor0 <ff705000.spi.0>, # parts = 6
216 * #: name size offset mask_flags
217 * 0: u-boot 0x00100000 0x00000000 0
218 * 1: env1 0x00040000 0x00100000 0
219 * 2: env2 0x00040000 0x00140000 0
220 * 3: UBI 0x03e80000 0x00180000 0
221 * 4: boot 0x00e80000 0x00180000 0
222 * 5: rootfs 0x01000000 0x01000000 0
229 * SRAM Memory layout:
231 * 0xFFFF_0000 ...... Start of SRAM
232 * 0xFFFF_xxxx ...... Top of stack (grows down)
233 * 0xFFFF_yyyy ...... Malloc area
234 * 0xFFFF_zzzz ...... Global Data
235 * 0xFFFF_FF00 ...... End of SRAM
237 #define CONFIG_SPL_TEXT_BASE CONFIG_SYS_INIT_RAM_ADDR
238 #define CONFIG_SPL_MAX_SIZE CONFIG_SYS_INIT_RAM_SIZE
240 /* SPL SDMMC boot support */
241 #ifdef CONFIG_SPL_MMC_SUPPORT
242 #if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
243 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
244 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
247 #ifndef CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
248 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
252 /* SPL QSPI boot support */
253 #ifdef CONFIG_SPL_SPI_SUPPORT
254 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x40000
257 /* SPL NAND boot support */
258 #ifdef CONFIG_SPL_NAND_SUPPORT
259 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
260 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
266 #define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
268 /* Extra Environment */
269 #ifndef CONFIG_SPL_BUILD
271 #ifdef CONFIG_CMD_DHCP
272 #define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
274 #define BOOT_TARGET_DEVICES_DHCP(func)
277 #if defined(CONFIG_CMD_PXE) && defined(CONFIG_CMD_DHCP)
278 #define BOOT_TARGET_DEVICES_PXE(func) func(PXE, pxe, na)
280 #define BOOT_TARGET_DEVICES_PXE(func)
283 #ifdef CONFIG_CMD_MMC
284 #define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
286 #define BOOT_TARGET_DEVICES_MMC(func)
289 #define BOOT_TARGET_DEVICES(func) \
290 BOOT_TARGET_DEVICES_MMC(func) \
291 BOOT_TARGET_DEVICES_PXE(func) \
292 BOOT_TARGET_DEVICES_DHCP(func)
294 #include <config_distro_bootcmd.h>
296 #ifndef CONFIG_EXTRA_ENV_SETTINGS
297 #define CONFIG_EXTRA_ENV_SETTINGS \
298 "fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
299 "bootm_size=0xa000000\0" \
300 "kernel_addr_r="__stringify(CONFIG_SYS_LOAD_ADDR)"\0" \
301 "fdt_addr_r=0x02000000\0" \
302 "scriptaddr=0x02100000\0" \
303 "pxefile_addr_r=0x02200000\0" \
304 "ramdisk_addr_r=0x02300000\0" \
310 #endif /* __CONFIG_SOCFPGA_COMMON_H__ */