ARM: configs: Add da850evm_nand to boot from NAND
[oweals/u-boot.git] / include / configs / rut.h
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * siemens rut
4  * (C) Copyright 2013 Siemens Schweiz AG
5  * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
6  *
7  * Based on:
8  * U-Boot file:/include/configs/am335x_evm.h
9  *
10  * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
11  */
12
13 #ifndef __CONFIG_RUT_H
14 #define __CONFIG_RUT_H
15
16 #define CONFIG_SIEMENS_MACH_TYPE        MACH_TYPE_RUT
17
18 #include "siemens-am33x-common.h"
19
20 #define RUT_IOCTRL_VAL  0x18b
21 #define DDR_PLL_FREQ    303
22
23  /* Physical Memory Map */
24 #define CONFIG_MAX_RAM_BANK_SIZE        (256 << 20) /* 256 MiB */
25
26 /* I2C Configuration */
27 #define CONFIG_SYS_I2C_SPEED            100000
28
29 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
30 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
31 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
32 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
33
34 #define CONFIG_PHY_NATSEMI
35
36 #define CONFIG_FACTORYSET
37
38 /* Watchdog */
39 #define WATCHDOG_TRIGGER_GPIO   14
40
41 #ifndef CONFIG_SPL_BUILD
42
43 /* Use common default */
44
45 /* Default env settings */
46 #define CONFIG_EXTRA_ENV_SETTINGS \
47         "hostname=rut\0" \
48         "ubi_off=2048\0"\
49         "nand_img_size=0x500000\0" \
50         "splashpos=m,m\0" \
51         "optargs=fixrtc --no-log consoleblank=0 \0" \
52         CONFIG_ENV_SETTINGS_V1 \
53         CONFIG_ENV_SETTINGS_NAND_V1 \
54         "mmc_dev=0\0" \
55         "mmc_root=/dev/mmcblk0p2 rw\0" \
56         "mmc_root_fs_type=ext4 rootwait\0" \
57         "mmc_load_uimage=" \
58                 "mmc rescan; " \
59                 "setenv bootfile uImage;" \
60                 "fatload mmc ${mmc_dev} ${kloadaddr} ${bootfile}\0" \
61         "loadbootenv=fatload mmc ${mmc_dev} ${loadaddr} ${bootenv}\0" \
62         "importbootenv=echo Importing environment from mmc ...; " \
63                 "env import -t $loadaddr $filesize\0" \
64         "mmc_args=run bootargs_defaults;" \
65                 "mtdparts default;" \
66                 "setenv bootargs ${bootargs} " \
67                 "root=${mmc_root} ${mtdparts}" \
68                 "rootfstype=${mmc_root_fs_type} ip=${ip_method} " \
69                 "eth=${ethaddr} " \
70                 "\0" \
71         "mmc_boot=run mmc_args; " \
72                 "run mmc_load_uimage; " \
73                 "bootm ${kloadaddr}\0" \
74         ""
75
76 #ifndef CONFIG_RESTORE_FLASH
77 /* set to negative value for no autoboot */
78
79 #define CONFIG_BOOTCOMMAND \
80         "if mmc rescan; then " \
81                 "echo SD/MMC found on device ${mmc_dev};" \
82                 "if run loadbootenv; then " \
83                         "echo Loaded environment from ${bootenv};" \
84                         "run importbootenv;" \
85                 "fi;" \
86                 "if test -n $uenvcmd; then " \
87                         "echo Running uenvcmd ...;" \
88                         "run uenvcmd;" \
89                 "fi;" \
90                 "if run mmc_load_uimage; then " \
91                         "run mmc_args;" \
92                         "bootm ${kloadaddr};" \
93                 "fi;" \
94         "fi;" \
95         "run nand_boot;" \
96         "reset;"
97
98 #else
99
100 #define CONFIG_BOOTCOMMAND                      \
101         "setenv autoload no; "                  \
102         "dhcp; "                                \
103         "if tftp 80000000 debrick.scr; then "   \
104                 "source 80000000; "             \
105         "fi"
106 #endif
107
108 #endif /* CONFIG_SPL_BUILD */
109
110 #if defined(CONFIG_VIDEO)
111 #define CONFIG_VIDEO_DA8XX
112 #define CONFIG_SPLASH_SCREEN
113 #define CONFIG_SPLASH_SCREEN_ALIGN
114 #define CONFIG_VIDEO_LOGO
115 #define CONFIG_VIDEO_BMP_RLE8
116 #define CONFIG_VIDEO_BMP_LOGO
117 #define DA8XX_LCD_CNTL_BASE     LCD_CNTL_BASE
118
119 #define BOARD_LCD_RESET         115     /* Bank 3 pin 19 */
120 #define CONFIG_FORMIKE
121 #define DISPL_PLL_SPREAD_SPECTRUM
122 #endif
123
124 #endif  /* ! __CONFIG_RUT_H */