1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * (C) Copyright 2006-2008
5 * Richard Woodruff <r-woodruff2@ti.com>
6 * Syed Mohammed Khasim <x0khasim@ti.com>
8 * Configuration settings for the TI OMAP3530 Beagle board.
14 #include <configs/ti_omap3_common.h>
17 * We are only ever GP parts and will utilize all of the "downloaded image"
18 * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB).
21 #define CONFIG_CMDLINE_TAG
22 #define CONFIG_SETUP_MEMORY_TAGS
23 #define CONFIG_INITRD_TAG
24 #define CONFIG_REVISION_TAG
27 #if defined(CONFIG_NAND)
28 #define CONFIG_SYS_FLASH_BASE NAND_BASE
29 #define CONFIG_SYS_MAX_NAND_DEVICE 1
30 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
31 #define CONFIG_SYS_NAND_PAGE_COUNT 64
32 #define CONFIG_SYS_NAND_PAGE_SIZE 2048
33 #define CONFIG_SYS_NAND_OOBSIZE 64
34 #define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
35 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
36 #define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
38 #define CONFIG_SYS_NAND_ECCSIZE 512
39 #define CONFIG_SYS_NAND_ECCBYTES 3
40 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
41 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
42 #define CONFIG_SYS_ENV_SECT_SIZE SZ_128K
43 #define CONFIG_ENV_ADDR 0x260000
44 #define CONFIG_ENV_OVERWRITE
45 /* NAND: SPL falcon mode configs */
46 #if defined(CONFIG_SPL_OS_BOOT)
47 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x2a0000
48 #endif /* CONFIG_SPL_OS_BOOT */
49 #endif /* CONFIG_NAND */
52 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
54 /* Enable Multi Bus support for I2C */
55 #define CONFIG_I2C_MULTI_BUS
59 /* TWL4030 LED Support */
61 #define CONFIG_PREBOOT "usb start"
63 #define MEM_LAYOUT_ENV_SETTINGS \
64 DEFAULT_LINUX_BOOT_ENV
66 #define BOOTENV_DEV_LEGACY_MMC(devtypeu, devtypel, instance) \
67 "bootcmd_" #devtypel #instance "=" \
68 "setenv mmcdev " #instance "; " \
70 #define BOOTENV_DEV_NAME_LEGACY_MMC(devtypeu, devtypel, instance) \
71 #devtypel #instance " "
73 #if defined(CONFIG_NAND)
75 #define BOOTENV_DEV_NAND(devtypeu, devtypel, instance) \
76 "bootcmd_" #devtypel #instance "=" \
77 "if test ${mtdids} = '' || test ${mtdparts} = '' ; then " \
78 "echo NAND boot disabled: No mtdids and/or mtdparts; " \
82 #define BOOTENV_DEV_NAME_NAND(devtypeu, devtypel, instance) \
83 #devtypel #instance " "
85 #define BOOT_TARGET_DEVICES(func) \
87 func(LEGACY_MMC, legacy_mmc, 0) \
88 func(UBIFS, ubifs, 0) \
91 #else /* !CONFIG_NAND */
93 #define BOOT_TARGET_DEVICES(func) \
95 func(LEGACY_MMC, legacy_mmc, 0)
97 #endif /* CONFIG_NAND */
99 #include <config_distro_bootcmd.h>
101 #define CONFIG_EXTRA_ENV_SETTINGS \
102 MEM_LAYOUT_ENV_SETTINGS \
103 "fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
104 "fdt_high=0xffffffff\0" \
105 "console=ttyO2,115200n8\0" \
107 "bootenv=uEnv.txt\0" \
108 "bootfile=zImage\0" \
110 "bootubivol=rootfs\0" \
111 "bootubipart=rootfs\0" \
117 "dvimode=640x480MR-16@60\0" \
118 "defaultdisplay=dvi\0" \
119 "defaultargs=setenv defargs " \
120 "mpurate=${mpurate} " \
124 "omapfb.mode=dvi:${dvimode} " \
125 "omapdss.def_disp=${defaultdisplay}\0" \
128 "if test $beaglerev = AxBx; then " \
129 "setenv fdtfile omap3-beagle.dtb; fi; " \
130 "if test $beaglerev = Cx; then " \
131 "setenv fdtfile omap3-beagle.dtb; fi; " \
132 "if test $beaglerev = C4; then " \
133 "setenv fdtfile omap3-beagle.dtb; fi; " \
134 "if test $beaglerev = xMAB; then " \
135 "setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \
136 "if test $beaglerev = xMC; then " \
137 "setenv fdtfile omap3-beagle-xm.dtb; fi; " \
138 "if test $fdtfile = undefined; then " \
139 "echo WARNING: Could not determine device tree to use; fi\0" \
142 "mmcroot=/dev/mmcblk0p2 rw\0" \
143 "mmcrootfstype=ext4 rootwait\0" \
144 "mmcargs=run defaultargs; setenv bootargs console=${console} " \
149 "rootfstype=${mmcrootfstype}\0" \
150 "userbutton_xm=gpio input 4;\0" \
151 "userbutton_nonxm=gpio input 7;\0" \
152 "userbutton=if gpio input 173; then " \
153 "run userbutton_xm; " \
155 "run userbutton_nonxm; " \
157 "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
158 "ext4bootenv=ext4load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootenv}\0" \
159 "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
160 "env import -t ${loadaddr} ${filesize}\0" \
161 "mmcbootenv=setenv bootpart ${mmcdev}:${mmcpart}; " \
162 "mmc dev ${mmcdev}; " \
163 "if mmc rescan; then " \
164 "if run userbutton; then " \
165 "setenv bootenv uEnv.txt;" \
167 "setenv bootenv user.txt;" \
169 "run loadbootenv && run importbootenv; " \
170 "run ext4bootenv && run importbootenv; " \
171 "if test -n $uenvcmd; then " \
172 "echo Running uenvcmd ...; " \
177 "if test $beaglerev = xMAB; then " \
178 "if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \
179 "setenv fdtfile omap3-beagle-xm.dtb; " \
182 "loadimage=ext4load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
183 "loaddtb=run validatefdt; ext4load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
184 "mmcboot=run mmcbootenv; " \
185 "if run loadimage && run loaddtb; then " \
186 "echo Booting ${bootdir}/${bootfile} from mmc ${bootpart} ...; " \
188 "if test ${bootfile} = uImage; then " \
189 "bootm ${loadaddr} - ${fdtaddr}; " \
191 "if test ${bootfile} = zImage; then " \
192 "bootz ${loadaddr} - ${fdtaddr}; " \
195 "nandroot=ubi0:rootfs ubi.mtd=rootfs rw\0" \
196 "nandrootfstype=ubifs rootwait\0" \
197 "nandargs=run defaultargs; setenv bootargs console=${console} " \
201 "root=${nandroot} " \
202 "rootfstype=${nandrootfstype}\0" \
203 "nandboot=if nand read ${loadaddr} kernel && nand read ${fdtaddr} dtb; then " \
204 "echo Booting uImage from NAND MTD 'kernel' partition ...; " \
206 "bootm ${loadaddr} - ${fdtaddr}; " \
208 "loadramdisk=ext4load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
209 "ramdisk=rootfs.ext2.gz.uboot\0" \
210 "ramdisk_size=16384\0" \
211 "ramroot=/dev/ram rw\0" \
212 "ramrootfstype=ext2\0" \
213 "ramargs=run defaultargs; setenv bootargs console=${console} " \
217 "root=${ramroot} ramdisk_size=${ramdisk_size} " \
218 "rootfstype=${ramrootfstype}\0" \
219 "ramboot=run mmcbootenv; " \
220 "if run loadimage && run loaddtb && run loadramdisk; then " \
221 "echo Booting ${bootdir}/${bootfile} from mmc ${bootpart} w/ramdisk ...; " \
223 "bootz ${loadaddr} ${rdaddr} ${fdtaddr}; " \
227 #endif /* __CONFIG_H */