2 * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
3 * Scott McNutt <smcnutt@psyent.com>
4 * (C) Copyright 2010, Thomas Chou <thomas@wytron.com.tw>
6 * SPDX-License-Identifier: GPL-2.0+
15 #include "../board/altera/nios2-generic/custom_fpga.h" /* fpga parameters */
16 #define CONFIG_BOARD_NAME "nios2-generic" /* custom board name */
17 #define CONFIG_BOARD_EARLY_INIT_F /* enable early board-spec. init */
18 #define CONFIG_BOARD_EARLY_INIT_R
19 #define CONFIG_DISPLAY_CPUINFO
20 #define CONFIG_DISPLAY_BOARDINFO
21 #define CONFIG_SYS_NIOS_SYSID_BASE CONFIG_SYS_SYSID_BASE
26 #define CONFIG_BAUDRATE 115200
27 #define CONFIG_SYS_CONSOLE_INFO_QUIET /* Suppress console info */
32 #define CONFIG_SYS_TIMER_RATE CONFIG_SYS_TIMER_FREQ
37 #define CONFIG_ALTERA_PIO
38 #define CONFIG_SYS_ALTERA_PIO_NUM 1
39 #define CONFIG_SYS_ALTERA_PIO_GPIO_NUM LED_PIO_WIDTH
41 #define CONFIG_STATUS_LED /* Enable status driver */
42 #define CONFIG_BOARD_SPECIFIC_LED
43 #define CONFIG_GPIO_LED /* Enable GPIO LED driver */
44 #define CONFIG_GPIO /* Enable GPIO driver */
45 #define LED_PIO_BASE USER_LED_PIO_8OUT_BASE
46 #define LED_PIO_WIDTH 8
47 #define LED_PIO_RSTVAL 0xff
49 #define STATUS_LED_BIT 0 /* Bit-0 on GPIO */
50 #define STATUS_LED_STATE 1 /* Blinking */
51 #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) /* 500 msec */
56 #define CONFIG_BOOTP_BOOTFILESIZE
57 #define CONFIG_BOOTP_BOOTPATH
58 #define CONFIG_BOOTP_GATEWAY
59 #define CONFIG_BOOTP_HOSTNAME
64 #define CONFIG_OF_LIBFDT
65 #define CONFIG_OF_BOARD_SETUP
69 * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
70 * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
71 * reset address, no? This will keep the environment in user region
72 * of flash. NOTE: the monitor length must be multiple of sector size
73 * (which is common practice).
75 #define CONFIG_ENV_IS_IN_FLASH
77 #define CONFIG_ENV_SIZE 0x20000 /* 128k, 1 sector */
78 #define CONFIG_ENV_OVERWRITE /* Serial change Ok */
79 #define CONFIG_ENV_ADDR ((CONFIG_SYS_RESET_ADDR + \
80 CONFIG_SYS_MONITOR_LEN) | \
81 CONFIG_SYS_FLASH_BASE)
85 * -Monitor at top of sdram.
86 * -The heap is placed below the monitor
87 * -The stack is placed below the heap (&grows down).
89 #define CONFIG_MONITOR_IS_IN_RAM
90 #define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256k */
91 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_SDRAM_BASE + \
92 CONFIG_SYS_SDRAM_SIZE - \
93 CONFIG_SYS_MONITOR_LEN)
94 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x20000)
95 #define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - \
96 CONFIG_SYS_MALLOC_LEN)
97 #define CONFIG_SYS_INIT_SP CONFIG_SYS_MALLOC_BASE
102 #define CONFIG_SYS_LONGHELP /* Provide extended help */
103 #define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */
104 #define CONFIG_SYS_MAXARGS 16 /* Max command args */
105 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Bootarg buf size */
106 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
107 sizeof(CONFIG_SYS_PROMPT) + \
108 16) /* Print buf size */
109 #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE
110 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
111 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_INIT_SP - 0x20000)
112 #define CONFIG_CMDLINE_EDITING
114 #endif /* __CONFIG_H */