sunxi: Add support for using MII phy-s with the GMAC nic
[oweals/u-boot.git] / include / configs / mecp5123.h
1 /*
2  * (C) Copyright 2009 Wolfgang Denk <wd@denx.de>
3  * (C) Copyright 2009, DAVE Srl <www.dave.eu>
4  *
5  * SPDX-License-Identifier:     GPL-2.0+
6  * modifications for the MECP5123 by reinhard.arlt@esd-electronics.com
7  *
8  */
9
10 /*
11  * MECP5123 board configuration file
12  */
13
14 #ifndef __CONFIG_H
15 #define __CONFIG_H
16
17 #define CONFIG_MECP5123 1
18 /*
19  * Memory map for the MECP5123 board:
20  *
21  * 0x0000_0000 - 0x1FFF_FFFF    DDR RAM (512 MB)
22  * 0x3000_0000 - 0x3001_FFFF    SRAM (128 KB)
23  * 0x8000_0000 - 0x803F_FFFF    IMMR (4 MB)
24  * 0x8200_0000 - 0x8200_FFFF    VPC-3 (64 KB)
25  * 0xFFC0_0000 - 0xFFFF_FFFF    NOR Boot FLASH (64 MB)
26  */
27
28 /*
29  * High Level Configuration Options
30  */
31 #define CONFIG_E300             1       /* E300 Family */
32
33 #define CONFIG_SYS_TEXT_BASE    0xFFF00000
34
35 #define CONFIG_SYS_MPC512X_CLKIN        33333333        /* in Hz */
36
37 #define CONFIG_BOARD_EARLY_INIT_F               /* call board_early_init_f() */
38 #define CONFIG_MISC_INIT_R
39
40 #define CONFIG_SYS_IMMR                 0x80000000
41 #define CONFIG_SYS_DIU_ADDR             (CONFIG_SYS_IMMR+0x2100)
42
43 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
44 #define CONFIG_SYS_MEMTEST_END          0x00400000
45
46 /*
47  * DDR Setup - manually set all parameters as there's no SPD etc.
48  */
49 #define CONFIG_SYS_DDR_SIZE             512             /* MB */
50
51 #define CONFIG_SYS_DDR_BASE             0x00000000      /* DDR is sys memory*/
52 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
53 #define CONFIG_SYS_MAX_RAM_SIZE         0x20000000
54
55 #define CONFIG_SYS_IOCTRL_MUX_DDR       0x00000036
56
57 /* DDR Controller Configuration
58  *
59  * SYS_CFG:
60  *      [31:31] MDDRC Soft Reset:       Diabled
61  *      [30:30] DRAM CKE pin:           Enabled
62  *      [29:29] DRAM CLK:               Enabled
63  *      [28:28] Command Mode:           Enabled (For initialization only)
64  *      [27:25] DRAM Row Select:        dram_row[15:0] = magenta_address[25:10]
65  *      [24:21] DRAM Bank Select:       dram_bank[1:0] = magenta_address[11:10]
66  *      [20:19] Read Test:              DON'T USE
67  *      [18:18] Self Refresh:           Enabled
68  *      [17:17] 16bit Mode:             Disabled
69  *      [16:13] Ready Delay:            2
70  *      [12:12] Half DQS Delay:         Disabled
71  *      [11:11] Quarter DQS Delay:      Disabled
72  *      [10:08] Write Delay:            2
73  *      [07:07] Early ODT:              Disabled
74  *      [06:06] On DIE Termination:     Disabled
75  *      [05:05] FIFO Overflow Clear:    DON'T USE here
76  *      [04:04] FIFO Underflow Clear:   DON'T USE here
77  *      [03:03] FIFO Overflow Pending:  DON'T USE here
78  *      [02:02] FIFO Underlfow Pending: DON'T USE here
79  *      [01:01] FIFO Overlfow Enabled:  Enabled
80  *      [00:00] FIFO Underflow Enabled: Enabled
81  * TIME_CFG0
82  *      [31:16] DRAM Refresh Time:      0 CSB clocks
83  *      [15:8]  DRAM Command Time:      0 CSB clocks
84  *      [07:00] DRAM Precharge Time:    0 CSB clocks
85  * TIME_CFG1
86  *      [31:26] DRAM tRFC:
87  *      [25:21] DRAM tWR1:
88  *      [20:17] DRAM tWRT1:
89  *      [16:11] DRAM tDRR:
90  *      [10:05] DRAM tRC:
91  *      [04:00] DRAM tRAS:
92  * TIME_CFG2
93  *      [31:28] DRAM tRCD:
94  *      [27:23] DRAM tFAW:
95  *      [22:19] DRAM tRTW1:
96  *      [18:15] DRAM tCCD:
97  *      [14:10] DRAM tRTP:
98  *      [09:05] DRAM tRP:
99  *      [04:00] DRAM tRPA
100  */
101 #define CONFIG_SYS_MDDRC_SYS_CFG         0xEA804A00
102 #define CONFIG_SYS_MDDRC_TIME_CFG0       0x06183D2E
103 #define CONFIG_SYS_MDDRC_TIME_CFG1       0x68EC1168
104 #define CONFIG_SYS_MDDRC_TIME_CFG2       0x34310864
105
106 #define CONFIG_SYS_DDRCMD_NOP           0x01380000
107 #define CONFIG_SYS_DDRCMD_PCHG_ALL      0x01100400
108 #define CONFIG_SYS_DDRCMD_EM2           0x01020000
109 #define CONFIG_SYS_DDRCMD_EM3           0x01030000
110 #define CONFIG_SYS_DDRCMD_EN_DLL        0x01010000
111 #define CONFIG_SYS_DDRCMD_RFSH          0x01080000
112 #define CONFIG_SYS_MICRON_INIT_DEV_OP   0x01000432
113 #define CONFIG_SYS_DDRCMD_OCD_DEFAULT   0x01010780
114
115 /* DDR Priority Manager Configuration */
116 #define CONFIG_SYS_MDDRCGRP_PM_CFG1     0x00077777
117 #define CONFIG_SYS_MDDRCGRP_PM_CFG2     0x00000000
118 #define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG  0x00000001
119 #define CONFIG_SYS_MDDRCGRP_LUT0_MU     0xFFEEDDCC
120 #define CONFIG_SYS_MDDRCGRP_LUT0_ML     0xBBAAAAAA
121 #define CONFIG_SYS_MDDRCGRP_LUT1_MU     0x66666666
122 #define CONFIG_SYS_MDDRCGRP_LUT1_ML     0x55555555
123 #define CONFIG_SYS_MDDRCGRP_LUT2_MU     0x44444444
124 #define CONFIG_SYS_MDDRCGRP_LUT2_ML     0x44444444
125 #define CONFIG_SYS_MDDRCGRP_LUT3_MU     0x55555555
126 #define CONFIG_SYS_MDDRCGRP_LUT3_ML     0x55555558
127 #define CONFIG_SYS_MDDRCGRP_LUT4_MU     0x11111111
128 #define CONFIG_SYS_MDDRCGRP_LUT4_ML     0x11111122
129 #define CONFIG_SYS_MDDRCGRP_LUT0_AU     0xaaaaaaaa
130 #define CONFIG_SYS_MDDRCGRP_LUT0_AL     0xaaaaaaaa
131 #define CONFIG_SYS_MDDRCGRP_LUT1_AU     0x66666666
132 #define CONFIG_SYS_MDDRCGRP_LUT1_AL     0x66666666
133 #define CONFIG_SYS_MDDRCGRP_LUT2_AU     0x11111111
134 #define CONFIG_SYS_MDDRCGRP_LUT2_AL     0x11111111
135 #define CONFIG_SYS_MDDRCGRP_LUT3_AU     0x11111111
136 #define CONFIG_SYS_MDDRCGRP_LUT3_AL     0x11111111
137 #define CONFIG_SYS_MDDRCGRP_LUT4_AU     0x11111111
138 #define CONFIG_SYS_MDDRCGRP_LUT4_AL     0x11111111
139
140 /*
141  * NOR FLASH on the Local Bus
142  */
143 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
144 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
145
146 #define CONFIG_SYS_FLASH_BASE           0xFFC00000      /* start of FLASH */
147 #define CONFIG_SYS_FLASH_SIZE           0x00400000      /* max flash size */
148
149 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
150 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
151 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE}
152 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max sectors per device */
153
154 #undef CONFIG_SYS_FLASH_CHECKSUM
155
156 /*
157  * NAND FLASH
158  * drivers/mtd/nand/mpc5121_nfc.c (rev 2 silicon only)
159  */
160 #define CONFIG_CMD_NAND
161 #define CONFIG_NAND_MPC5121_NFC
162 #define CONFIG_SYS_NAND_BASE            0x40000000
163 #define CONFIG_SYS_MAX_NAND_DEVICE      1
164
165 /*
166  * Configuration parameters for MPC5121 NAND driver
167  */
168 #define CONFIG_FSL_NFC_WIDTH            1
169 #define CONFIG_FSL_NFC_WRITE_SIZE       2048
170 #define CONFIG_FSL_NFC_SPARE_SIZE       64
171 #define CONFIG_FSL_NFC_CHIPS            1
172
173 #define CONFIG_SYS_SRAM_BASE            0x30000000
174 #define CONFIG_SYS_SRAM_SIZE            0x00020000      /* 128 KB */
175
176 /* Initialize Local Window for NOR FLASH access */
177 #define CONFIG_SYS_CS0_START            CONFIG_SYS_FLASH_BASE
178 #define CONFIG_SYS_CS0_SIZE             CONFIG_SYS_FLASH_SIZE
179
180 /* ALE active low, data size 4bytes */
181 #define CONFIG_SYS_CS0_CFG              0x05051150
182
183 /* Use not alternative CS timing */
184 #define CONFIG_SYS_CS_ALETIMING         0x00000000
185
186 /* ALE active low, data size 4bytes */
187 #define CONFIG_SYS_CS1_CFG              0x1f1f3090
188 #define CONFIG_SYS_VPC3_BASE            0x82000000      /* start of VPC3 space */
189 #define CONFIG_SYS_VPC3_SIZE            0x00010000      /* max VPC3 size */
190 /* Initialize Local Window for VPC3 access */
191 #define CONFIG_SYS_CS1_START            CONFIG_SYS_VPC3_BASE
192 #define CONFIG_SYS_CS1_SIZE             CONFIG_SYS_VPC3_SIZE
193
194 /* Use SRAM for initial stack */
195 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_SRAM_BASE /* Init RAM addr */
196 #define CONFIG_SYS_INIT_RAM_SIZE                CONFIG_SYS_SRAM_SIZE
197
198 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
199 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
200
201 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE    /* Start of monitor */
202 #define CONFIG_SYS_MONITOR_LEN          (256 * 1024)    /* Monitor length */
203 #define CONFIG_SYS_MALLOC_LEN           (6 * 1024 * 1024) /* Malloc size */
204
205 /*
206  * Serial Port
207  */
208 #define CONFIG_CONS_INDEX     1
209
210 /*
211  * Serial console configuration
212  */
213 #define CONFIG_PSC_CONSOLE      3       /* console is on PSC3 */
214 #define CONFIG_SYS_PSC3
215 #if CONFIG_PSC_CONSOLE != 3
216 #error CONFIG_PSC_CONSOLE must be 3
217 #endif
218 #define CONFIG_BAUDRATE         9600    /* ... at 9600 bps */
219 #define CONFIG_SYS_BAUDRATE_TABLE  \
220         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
221
222 #define CONSOLE_FIFO_TX_SIZE    FIFOC_PSC3_TX_SIZE
223 #define CONSOLE_FIFO_TX_ADDR    FIFOC_PSC3_TX_ADDR
224 #define CONSOLE_FIFO_RX_SIZE    FIFOC_PSC3_RX_SIZE
225 #define CONSOLE_FIFO_RX_ADDR    FIFOC_PSC3_RX_ADDR
226
227 /*
228  * Clocks in use
229  */
230 #define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN |                           \
231                          CLOCK_SCCR1_LPC_EN |                           \
232                          CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) |       \
233                          CLOCK_SCCR1_PSCFIFO_EN |                       \
234                          CLOCK_SCCR1_DDR_EN |                           \
235                          CLOCK_SCCR1_FEC_EN |                           \
236                          CLOCK_SCCR1_NFC_EN |                           \
237                          CLOCK_SCCR1_PCI_EN |                           \
238                          CLOCK_SCCR1_TPR_EN)
239
240 #define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN |   \
241                          CLOCK_SCCR2_I2C_EN)
242
243
244 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
245 /* Use the HUSH parser */
246 #define CONFIG_SYS_HUSH_PARSER
247 #ifdef  CONFIG_SYS_HUSH_PARSER
248 #endif
249
250 /* I2C */
251 #define CONFIG_HARD_I2C                 /* I2C with hardware support */
252 #define CONFIG_I2C_MULTI_BUS
253 #define CONFIG_SYS_I2C_SPEED            400000  /* I2C speed */
254 #define CONFIG_SYS_I2C_SLAVE            0x7F    /* slave address */
255
256 /*
257  * IIM - IC Identification Module
258  */
259 #undef CONFIG_FSL_IIM
260
261 /*
262  * EEPROM configuration
263  */
264 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2       /* 16-bit EEPROM address */
265 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* Atmel: AT24C32A-10TQ-2.7 */
266 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10        /* 10ms of delay */
267 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5     /* 32-Byte Page Write Mode */
268 #define CONFIG_SYS_EEPROM_WREN                  /* Use EEPROM write protect */
269
270 /*
271  * Ethernet configuration
272  */
273 #define CONFIG_MPC512x_FEC      1
274 #define CONFIG_PHY_ADDR         0x1
275 #define CONFIG_MII              1       /* MII PHY management           */
276 #define CONFIG_FEC_AN_TIMEOUT   1
277 #define CONFIG_HAS_ETH0
278
279 /*
280  * Configure on-board RTC
281  */
282 #define CONFIG_SYS_RTC_BUS_NUM  0x01
283 #define CONFIG_SYS_I2C_RTC_ADDR 0x32
284 #define CONFIG_RTC_RX8025
285
286 /*
287  * Environment
288  */
289 #define CONFIG_ENV_IS_IN_EEPROM         /* Store env in I2C EEPROM      */
290 #define CONFIG_ENV_SIZE         0x1000
291 #define CONFIG_ENV_OFFSET       0x0000  /* environment starts here      */
292
293 #define CONFIG_LOADS_ECHO               /* echo on for serial download  */
294 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change        */
295
296 #include <config_cmd_default.h>
297
298 #define CONFIG_CMD_ASKENV
299 #define CONFIG_CMD_DHCP
300 #define CONFIG_CMD_I2C
301 #define CONFIG_CMD_MII
302 #define CONFIG_CMD_NFS
303 #define CONFIG_CMD_PING
304 #define CONFIG_CMD_REGINFO
305 #define CONFIG_CMD_EEPROM
306 #define CONFIG_CMD_DATE
307 #undef CONFIG_CMD_FUSE
308 #undef CONFIG_CMD_IDE
309 #undef CONFIG_CMD_EXT2
310 #define CONFIG_CMD_FAT
311 #define CONFIG_CMD_JFFS2
312 #define CONFIG_CMD_ELF
313 #define CONFIG_DOS_PARTITION
314
315 /*
316  * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
317  * For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE is set
318  * to 0xFFFF, watchdog timeouts after about 64s. For details refer
319  * to chapter 36 of the MPC5121e Reference Manual.
320  */
321 /* #define CONFIG_WATCHDOG */           /* enable watchdog */
322 #define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF
323
324  /*
325  * Miscellaneous configurable options
326  */
327 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
328 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
329
330 #ifdef CONFIG_CMD_KGDB
331 # define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
332 #else
333 # define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
334 #endif
335
336 /* Print Buffer Size */
337 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
338                                  sizeof(CONFIG_SYS_PROMPT) + 16)
339 /* max number of command args */
340 #define CONFIG_SYS_MAXARGS      32
341 /* Boot Argument Buffer Size */
342 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
343
344 /*
345  * For booting Linux, the board info and command line data
346  * have to be in the first 256 MB of memory, since this is
347  * the maximum mapped by the Linux kernel during initialization.
348  */
349 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)     /* Linux initial memory map */
350
351 /* Cache Configuration */
352 #define CONFIG_SYS_DCACHE_SIZE          32768
353 #define CONFIG_SYS_CACHELINE_SIZE       32
354 #ifdef CONFIG_CMD_KGDB
355 #define CONFIG_SYS_CACHELINE_SHIFT      5
356 #endif
357
358 #define CONFIG_SYS_HID0_INIT    0x000000000
359 #define CONFIG_SYS_HID0_FINAL   HID0_ENABLE_MACHINE_CHECK
360 #define CONFIG_SYS_HID2         HID2_HBE
361
362 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
363
364 #ifdef CONFIG_CMD_KGDB
365 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
366 #endif
367
368 /*
369  * Environment Configuration
370  */
371 #define CONFIG_TIMESTAMP
372
373 #define CONFIG_HOSTNAME         mecp512x
374 #define CONFIG_BOOTFILE         "/tftpboot/mecp512x/uImage"
375 #define CONFIG_ROOTPATH         "/tftpboot/mecp512x/target_root"
376
377 #define CONFIG_LOADADDR         400000  /* def. location for tftp and bootm */
378
379 #define CONFIG_BOOTDELAY        5       /* -1 disables auto-boot */
380 #undef  CONFIG_BOOTARGS                 /* the boot command will set bootargs*/
381
382 #define CONFIG_PREBOOT  "echo;" \
383         "echo Welcome to MECP5123" \
384         "echo"
385
386 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
387         "u-boot_addr_r=200000\0"                                        \
388         "kernel_addr_r=600000\0"                                        \
389         "fdt_addr_r=880000\0"                                           \
390         "ramdisk_addr_r=900000\0"                                       \
391         "u-boot_addr=FFF00000\0"                                        \
392         "kernel_addr=FFC40000\0"                                        \
393         "fdt_addr=FFEC0000\0"                                           \
394         "ramdisk_addr=FC040000\0"                                       \
395         "ramdiskfile=/tftpboot/mecp512x/uRamdisk\0"                     \
396         "u-boot=/tftpboot/mecp512x/u-boot.bin\0"                        \
397         "bootfile=/tftpboot/mecp512x/uImage\0"                          \
398         "fdtfile=/tftpboot/mecp512x/mecp512x.dtb\0"                     \
399         "rootpath=/tftpboot/mecp512x/target_root\n"                     \
400         "netdev=eth0\0"                                                 \
401         "consdev=ttyPSC0\0"                                             \
402         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
403                 "nfsroot=${serverip}:${rootpath}\0"                     \
404         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
405         "addip=setenv bootargs ${bootargs} "                            \
406                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
407                 ":${hostname}:${netdev}:off panic=1\0"                  \
408         "addtty=setenv bootargs ${bootargs} "                           \
409                 "console=${consdev},${baudrate}\0"                      \
410         "flash_nfs=run nfsargs addip addtty;"                           \
411                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
412         "flash_self=run ramargs addip addtty;"                          \
413                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
414         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
415                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
416                 "run nfsargs addip addtty;"                             \
417                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
418         "net_self=tftp ${kernel_addr_r} ${bootfile};"                   \
419                 "tftp ${ramdisk_addr_r} ${ramdiskfile};"                \
420                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
421                 "run ramargs addip addtty;"                             \
422                 "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\
423         "load=tftp ${u-boot_addr_r} ${u-boot}\0"                        \
424         "update=protect off ${u-boot_addr} +${filesize};"               \
425                 "era ${u-boot_addr} +${filesize};"                      \
426                 "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0"    \
427         "upd=run load update\0"                                         \
428         ""
429
430 #define CONFIG_BOOTCOMMAND      "run flash_self"
431
432 #define CONFIG_OF_LIBFDT
433 #define CONFIG_OF_BOARD_SETUP
434
435 #define OF_CPU                  "PowerPC,5121@0"
436 #define OF_SOC_COMPAT           "fsl,mpc5121-immr"
437 #define OF_TBCLK                (bd->bi_busfreq / 4)
438 #define OF_STDOUT_PATH          "/soc@80000000/serial@11300"
439
440 #endif  /* __CONFIG_H */