1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright (c) 2012 Michael Walle
4 * Michael Walle <michael@walle.cc>
11 * Version number information
13 #if defined(CONFIG_LSCHLV2)
14 #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-lschl.cfg
15 #define CONFIG_MACH_TYPE 3006
16 #define CONFIG_SYS_TCLK 166666667 /* 166 MHz */
17 #elif defined(CONFIG_LSXHL)
18 #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-lsxhl.cfg
19 #define CONFIG_MACH_TYPE 2663
20 /* CONFIG_SYS_TCLK is 200000000 by default */
22 #error "unknown board"
26 * General configuration options
28 #define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
29 #define CONFIG_KW88F6281 /* SOC Name */
31 #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
33 #define CONFIG_KIRKWOOD_GPIO
36 * Commands configuration
40 * mv-common.h should be defined after CMD configs since it used them
41 * to enable certain macros
43 #include "mv-common.h"
45 /* loading initramfs images without uimage header */
48 * Environment variables configurations
50 #ifdef CONFIG_SPI_FLASH
51 #define CONFIG_SYS_MAX_FLASH_BANKS 1
52 #define CONFIG_SYS_MAX_FLASH_SECT 8
53 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K */
56 #define CONFIG_ENV_SIZE 0x10000 /* 64k */
57 #define CONFIG_ENV_OFFSET 0x70000 /* env starts here */
60 * Default environment variables
62 #define CONFIG_LOADADDR 0x00800000
64 #if defined(CONFIG_LSXHL)
65 #define CONFIG_FDTFILE "kirkwood-lsxhl.dtb"
66 #elif defined(CONFIG_LSCHLV2)
67 #define CONFIG_FDTFILE "kirkwood-lschlv2.dtb"
69 #error "Unsupported board"
72 #define CONFIG_EXTRA_ENV_SETTINGS \
73 "bootsource=legacy\0" \
75 "kernel_addr=0x00800000\0" \
76 "ramdisk_addr=0x01000000\0" \
77 "fdt_addr=0x00ff0000\0" \
78 "bootcmd_legacy=sata init " \
79 "&& load sata ${hdpart} ${kernel_addr} /uImage.buffalo "\
80 "&& load sata ${hdpart} ${ramdisk_addr} /initrd.buffalo "\
81 "&& bootm ${kernel_addr} ${ramdisk_addr}\0" \
82 "bootcmd_net=bootp ${kernel_addr} vmlinuz " \
83 "&& tftpboot ${ramdisk_addr} initrd.img " \
84 "&& setenv ramdisk_len ${filesize} " \
85 "&& tftpboot ${fdt_addr} " CONFIG_FDTFILE " " \
86 "&& bootz ${kernel_addr} " \
87 "${ramdisk_addr}:${ramdisk_len} ${fdt_addr}\0" \
88 "bootcmd_hdd=sata init " \
89 "&& load sata ${hdpart} ${kernel_addr} /vmlinuz " \
90 "&& load sata ${hdpart} ${ramdisk_addr} /initrd.img " \
91 "&& setenv ramdisk_len ${filesize} " \
92 "&& load sata ${hdpart} ${fdt_addr} /dtb " \
93 "&& bootz ${kernel_addr} " \
94 "${ramdisk_addr}:${ramdisk_len} ${fdt_addr}\0" \
95 "bootcmd_usb=usb start " \
96 "&& load usb 0:1 ${kernel_addr} /vmlinuz " \
97 "&& load usb 0:1 ${ramdisk_addr} /initrd.img " \
98 "&& setenv ramdisk_len ${filesize} " \
99 "&& load usb 0:1 ${fdt_addr} " CONFIG_FDTFILE " " \
100 "&& bootz ${kernel_addr} " \
101 "${ramdisk_addr}:${ramdisk_len} ${fdt_addr}\0" \
102 "bootcmd_rescue=run config_nc_dhcp; run nc\0" \
103 "eraseenv=sf probe 0 " \
104 "&& sf erase " __stringify(CONFIG_ENV_OFFSET) \
105 " +" __stringify(CONFIG_ENV_SIZE) "\0" \
106 "config_nc_dhcp=setenv autoload_old ${autoload}; " \
107 "setenv autoload no " \
110 "&& setenv autoload ${autoload_old}; " \
111 "setenv autoload_old\0" \
112 "standard_env=setenv ipaddr; setenv netmask; setenv serverip; " \
113 "setenv ncip; setenv gatewayip; setenv ethact; " \
114 "setenv bootfile; setenv dnsip; " \
115 "setenv bootsource legacy; run ser\0" \
116 "restore_env=run standard_env; saveenv; reset\0" \
117 "ser=setenv stdin serial; setenv stdout serial; " \
118 "setenv stderr serial\0" \
119 "nc=setenv stdin nc; setenv stdout nc; setenv stderr nc\0" \
125 * Ethernet Driver configuration
127 #ifdef CONFIG_CMD_NET
128 #define CONFIG_MVGBE_PORTS {0, 1} /* enable port 1 only */
129 #define CONFIG_PHY_BASE_ADR 7
130 #undef CONFIG_RESET_PHY_R
131 #endif /* CONFIG_CMD_NET */
134 #define CONFIG_SYS_SATA_MAX_DEVICE 1
135 #define CONFIG_SYS_64BIT_LBA
139 #endif /* _CONFIG_LSXL_H */