ARM: configs: Add da850evm_nand to boot from NAND
[oweals/u-boot.git] / include / configs / ls1046aqds.h
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright 2016 Freescale Semiconductor, Inc.
4  */
5
6 #ifndef __LS1046AQDS_H__
7 #define __LS1046AQDS_H__
8
9 #include "ls1046a_common.h"
10
11 #ifndef __ASSEMBLY__
12 unsigned long get_board_sys_clk(void);
13 unsigned long get_board_ddr_clk(void);
14 #endif
15
16 #define CONFIG_SYS_CLK_FREQ             get_board_sys_clk()
17 #define CONFIG_DDR_CLK_FREQ             get_board_ddr_clk()
18
19 #define CONFIG_SKIP_LOWLEVEL_INIT
20
21 #define CONFIG_LAYERSCAPE_NS_ACCESS
22
23 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
24 /* Physical Memory Map */
25 #define CONFIG_CHIP_SELECTS_PER_CTRL    4
26
27 #define CONFIG_DDR_SPD
28 #define SPD_EEPROM_ADDRESS              0x51
29 #define CONFIG_SYS_SPD_BUS_NUM          0
30
31 #ifndef CONFIG_SPL
32 #define CONFIG_FSL_DDR_INTERACTIVE      /* Interactive debugging */
33 #endif
34
35 #define CONFIG_DDR_ECC
36 #ifdef CONFIG_DDR_ECC
37 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
38 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
39 #endif
40
41 /* DSPI */
42 #ifdef CONFIG_FSL_DSPI
43 #define CONFIG_SPI_FLASH_STMICRO        /* cs0 */
44 #define CONFIG_SPI_FLASH_SST            /* cs1 */
45 #define CONFIG_SPI_FLASH_EON            /* cs2 */
46 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
47 #define CONFIG_SF_DEFAULT_BUS           1
48 #define CONFIG_SF_DEFAULT_CS            0
49 #endif
50 #endif
51
52 /* QSPI */
53 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
54 #ifdef CONFIG_FSL_QSPI
55 #define CONFIG_SPI_FLASH_SPANSION
56 #define FSL_QSPI_FLASH_SIZE             (1 << 24)
57 #define FSL_QSPI_FLASH_NUM              2
58 #endif
59 #endif
60
61 #ifdef CONFIG_SYS_DPAA_FMAN
62 #define CONFIG_FMAN_ENET
63 #define CONFIG_PHY_VITESSE
64 #define CONFIG_PHY_REALTEK
65 #define CONFIG_PHYLIB_10G
66 #define RGMII_PHY1_ADDR         0x1
67 #define RGMII_PHY2_ADDR         0x2
68 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
69 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
70 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
71 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
72 /* PHY address on QSGMII riser card on slot 2 */
73 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
74 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
75 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
76 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
77 #endif
78
79 #ifdef CONFIG_RAMBOOT_PBL
80 #define CONFIG_SYS_FSL_PBL_PBI \
81         board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
82 #endif
83
84 #ifdef CONFIG_NAND_BOOT
85 #define CONFIG_SYS_FSL_PBL_RCW \
86         board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
87 #endif
88
89 #ifdef CONFIG_SD_BOOT
90 #ifdef CONFIG_SD_BOOT_QSPI
91 #define CONFIG_SYS_FSL_PBL_RCW \
92         board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
93 #else
94 #define CONFIG_SYS_FSL_PBL_RCW \
95         board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
96 #endif
97 #endif
98
99 /* IFC */
100 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
101 #define CONFIG_FSL_IFC
102 /*
103  * CONFIG_SYS_FLASH_BASE has the final address (core view)
104  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
105  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
106  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
107  */
108 #define CONFIG_SYS_FLASH_BASE                   0x60000000
109 #define CONFIG_SYS_FLASH_BASE_PHYS              CONFIG_SYS_FLASH_BASE
110 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY        0x00000000
111
112 #ifdef CONFIG_MTD_NOR_FLASH
113 #define CONFIG_FLASH_CFI_DRIVER
114 #define CONFIG_SYS_FLASH_CFI
115 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
116 #define CONFIG_SYS_FLASH_QUIET_TEST
117 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
118 #endif
119 #endif
120
121 /* LPUART */
122 #ifdef CONFIG_LPUART
123 #define CONFIG_LPUART_32B_REG
124 #define CFG_UART_MUX_MASK       0x6
125 #define CFG_UART_MUX_SHIFT      1
126 #define CFG_LPUART_EN           0x2
127 #endif
128
129 /* EEPROM */
130 #define CONFIG_ID_EEPROM
131 #define CONFIG_SYS_I2C_EEPROM_NXID
132 #define CONFIG_SYS_EEPROM_BUS_NUM               0
133 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x57
134 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
135 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       3
136 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   5
137
138 /*
139  * IFC Definitions
140  */
141 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
142 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
143 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
144                                 CSPR_PORT_SIZE_16 | \
145                                 CSPR_MSEL_NOR | \
146                                 CSPR_V)
147 #define CONFIG_SYS_NOR1_CSPR_EXT        (0x0)
148 #define CONFIG_SYS_NOR1_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
149                                 + 0x8000000) | \
150                                 CSPR_PORT_SIZE_16 | \
151                                 CSPR_MSEL_NOR | \
152                                 CSPR_V)
153 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128 * 1024 * 1024)
154
155 #define CONFIG_SYS_NOR_CSOR             (CSOR_NOR_ADM_SHIFT(4) | \
156                                         CSOR_NOR_TRHZ_80)
157 #define CONFIG_SYS_NOR_FTIM0            (FTIM0_NOR_TACSE(0x4) | \
158                                         FTIM0_NOR_TEADC(0x5) | \
159                                         FTIM0_NOR_TAVDS(0x6) | \
160                                         FTIM0_NOR_TEAHC(0x5))
161 #define CONFIG_SYS_NOR_FTIM1            (FTIM1_NOR_TACO(0x35) | \
162                                         FTIM1_NOR_TRAD_NOR(0x1a) | \
163                                         FTIM1_NOR_TSEQRAD_NOR(0x13))
164 #define CONFIG_SYS_NOR_FTIM2            (FTIM2_NOR_TCS(0x8) | \
165                                         FTIM2_NOR_TCH(0x8) | \
166                                         FTIM2_NOR_TWPH(0xe) | \
167                                         FTIM2_NOR_TWP(0x1c))
168 #define CONFIG_SYS_NOR_FTIM3            0
169
170 #define CONFIG_SYS_MAX_FLASH_BANKS      2       /* number of banks */
171 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
172 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
173 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
174
175 #define CONFIG_SYS_FLASH_EMPTY_INFO
176 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS, \
177                                         CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
178
179 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
180 #define CONFIG_SYS_WRITE_SWAPPED_DATA
181
182 /*
183  * NAND Flash Definitions
184  */
185 #define CONFIG_NAND_FSL_IFC
186
187 #define CONFIG_SYS_NAND_BASE            0x7e800000
188 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
189
190 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
191
192 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
193                                 | CSPR_PORT_SIZE_8      \
194                                 | CSPR_MSEL_NAND        \
195                                 | CSPR_V)
196 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
197 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
198                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
199                                 | CSOR_NAND_ECC_MODE_8  /* 8-bit ECC */ \
200                                 | CSOR_NAND_RAL_3       /* RAL = 3 Bytes */ \
201                                 | CSOR_NAND_PGS_4K      /* Page Size = 4K */ \
202                                 | CSOR_NAND_SPRZ_224    /* Spare size = 224 */ \
203                                 | CSOR_NAND_PB(64))     /* 64 Pages Per Block */
204
205 #define CONFIG_SYS_NAND_ONFI_DETECTION
206
207 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x7) | \
208                                         FTIM0_NAND_TWP(0x18)   | \
209                                         FTIM0_NAND_TWCHT(0x7) | \
210                                         FTIM0_NAND_TWH(0xa))
211 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
212                                         FTIM1_NAND_TWBE(0x39)  | \
213                                         FTIM1_NAND_TRR(0xe)   | \
214                                         FTIM1_NAND_TRP(0x18))
215 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0xf) | \
216                                         FTIM2_NAND_TREH(0xa) | \
217                                         FTIM2_NAND_TWHRE(0x1e))
218 #define CONFIG_SYS_NAND_FTIM3           0x0
219
220 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
221 #define CONFIG_SYS_MAX_NAND_DEVICE      1
222 #define CONFIG_MTD_NAND_VERIFY_WRITE
223
224 #define CONFIG_SYS_NAND_BLOCK_SIZE      (256 * 1024)
225 #endif
226
227 #ifdef CONFIG_NAND_BOOT
228 #define CONFIG_SPL_PAD_TO               0x40000         /* block aligned */
229 #define CONFIG_SYS_NAND_U_BOOT_OFFS     CONFIG_SPL_PAD_TO
230 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
231 #endif
232
233 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
234 #define CONFIG_QIXIS_I2C_ACCESS
235 #define CONFIG_SYS_I2C_EARLY_INIT
236 #endif
237
238 /*
239  * QIXIS Definitions
240  */
241 #define CONFIG_FSL_QIXIS
242
243 #ifdef CONFIG_FSL_QIXIS
244 #define QIXIS_BASE                      0x7fb00000
245 #define QIXIS_BASE_PHYS                 QIXIS_BASE
246 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
247 #define QIXIS_LBMAP_SWITCH              6
248 #define QIXIS_LBMAP_MASK                0x0f
249 #define QIXIS_LBMAP_SHIFT               0
250 #define QIXIS_LBMAP_DFLTBANK            0x00
251 #define QIXIS_LBMAP_ALTBANK             0x04
252 #define QIXIS_LBMAP_NAND                0x09
253 #define QIXIS_LBMAP_SD                  0x00
254 #define QIXIS_LBMAP_SD_QSPI             0xff
255 #define QIXIS_LBMAP_QSPI                0xff
256 #define QIXIS_RCW_SRC_NAND              0x110
257 #define QIXIS_RCW_SRC_SD                0x040
258 #define QIXIS_RCW_SRC_QSPI              0x045
259 #define QIXIS_RST_CTL_RESET             0x41
260 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
261 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
262 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
263
264 #define CONFIG_SYS_FPGA_CSPR_EXT        (0x0)
265 #define CONFIG_SYS_FPGA_CSPR            (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
266                                         CSPR_PORT_SIZE_8 | \
267                                         CSPR_MSEL_GPCM | \
268                                         CSPR_V)
269 #define CONFIG_SYS_FPGA_AMASK           IFC_AMASK(64 * 1024)
270 #define CONFIG_SYS_FPGA_CSOR            (CSOR_NOR_ADM_SHIFT(4) | \
271                                         CSOR_NOR_NOR_MODE_AVD_NOR | \
272                                         CSOR_NOR_TRHZ_80)
273
274 /*
275  * QIXIS Timing parameters for IFC GPCM
276  */
277 #define CONFIG_SYS_FPGA_FTIM0           (FTIM0_GPCM_TACSE(0xc) | \
278                                         FTIM0_GPCM_TEADC(0x20) | \
279                                         FTIM0_GPCM_TEAHC(0x10))
280 #define CONFIG_SYS_FPGA_FTIM1           (FTIM1_GPCM_TACO(0x50) | \
281                                         FTIM1_GPCM_TRAD(0x1f))
282 #define CONFIG_SYS_FPGA_FTIM2           (FTIM2_GPCM_TCS(0x8) | \
283                                         FTIM2_GPCM_TCH(0x8) | \
284                                         FTIM2_GPCM_TWP(0xf0))
285 #define CONFIG_SYS_FPGA_FTIM3           0x0
286 #endif
287
288 #ifdef CONFIG_NAND_BOOT
289 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
290 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
291 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
292 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
293 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
294 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
295 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
296 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
297 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
298 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
299 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
300 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
301 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
302 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
303 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
304 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
305 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR1_CSPR_EXT
306 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR1_CSPR
307 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
308 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
309 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
310 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
311 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
312 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
313 #define CONFIG_SYS_CSPR3_EXT            CONFIG_SYS_FPGA_CSPR_EXT
314 #define CONFIG_SYS_CSPR3                CONFIG_SYS_FPGA_CSPR
315 #define CONFIG_SYS_AMASK3               CONFIG_SYS_FPGA_AMASK
316 #define CONFIG_SYS_CSOR3                CONFIG_SYS_FPGA_CSOR
317 #define CONFIG_SYS_CS3_FTIM0            CONFIG_SYS_FPGA_FTIM0
318 #define CONFIG_SYS_CS3_FTIM1            CONFIG_SYS_FPGA_FTIM1
319 #define CONFIG_SYS_CS3_FTIM2            CONFIG_SYS_FPGA_FTIM2
320 #define CONFIG_SYS_CS3_FTIM3            CONFIG_SYS_FPGA_FTIM3
321 #else
322 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
323 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
324 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
325 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
326 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
327 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
328 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
329 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
330 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR1_CSPR_EXT
331 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR1_CSPR
332 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
333 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
334 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
335 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
336 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
337 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
338 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
339 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
340 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
341 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
342 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
343 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
344 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
345 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
346 #define CONFIG_SYS_CSPR3_EXT            CONFIG_SYS_FPGA_CSPR_EXT
347 #define CONFIG_SYS_CSPR3                CONFIG_SYS_FPGA_CSPR
348 #define CONFIG_SYS_AMASK3               CONFIG_SYS_FPGA_AMASK
349 #define CONFIG_SYS_CSOR3                CONFIG_SYS_FPGA_CSOR
350 #define CONFIG_SYS_CS3_FTIM0            CONFIG_SYS_FPGA_FTIM0
351 #define CONFIG_SYS_CS3_FTIM1            CONFIG_SYS_FPGA_FTIM1
352 #define CONFIG_SYS_CS3_FTIM2            CONFIG_SYS_FPGA_FTIM2
353 #define CONFIG_SYS_CS3_FTIM3            CONFIG_SYS_FPGA_FTIM3
354 #endif
355
356 /*
357  * I2C bus multiplexer
358  */
359 #define I2C_MUX_PCA_ADDR_PRI            0x77
360 #define I2C_MUX_PCA_ADDR_SEC            0x76 /* Secondary multiplexer */
361 #define I2C_RETIMER_ADDR                0x18
362 #define I2C_MUX_CH_DEFAULT              0x8
363 #define I2C_MUX_CH_CH7301               0xC
364 #define I2C_MUX_CH5                     0xD
365 #define I2C_MUX_CH6                     0xE
366 #define I2C_MUX_CH7                     0xF
367
368 #define I2C_MUX_CH_VOL_MONITOR 0xa
369
370 /* Voltage monitor on channel 2*/
371 #define I2C_VOL_MONITOR_ADDR           0x40
372 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
373 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
374 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
375
376 #define CONFIG_VID_FLS_ENV              "ls1046aqds_vdd_mv"
377 #ifndef CONFIG_SPL_BUILD
378 #define CONFIG_VID
379 #endif
380 #define CONFIG_VOL_MONITOR_IR36021_SET
381 #define CONFIG_VOL_MONITOR_INA220
382 /* The lowest and highest voltage allowed for LS1046AQDS */
383 #define VDD_MV_MIN                      819
384 #define VDD_MV_MAX                      1212
385
386 /*
387  * Miscellaneous configurable options
388  */
389
390 #define CONFIG_SYS_MEMTEST_START        0x80000000
391 #define CONFIG_SYS_MEMTEST_END          0x9fffffff
392
393 #define CONFIG_SYS_HZ                   1000
394
395 #define CONFIG_SYS_INIT_SP_OFFSET \
396         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
397
398 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
399
400 /*
401  * Environment
402  */
403 #define CONFIG_ENV_OVERWRITE
404
405 #ifdef CONFIG_NAND_BOOT
406 #define CONFIG_ENV_SIZE                 0x2000
407 #define CONFIG_ENV_OFFSET               (12 * CONFIG_SYS_NAND_BLOCK_SIZE)
408 #elif defined(CONFIG_SD_BOOT)
409 #define CONFIG_ENV_OFFSET               (3 * 1024 * 1024)
410 #define CONFIG_SYS_MMC_ENV_DEV          0
411 #define CONFIG_ENV_SIZE                 0x2000
412 #elif defined(CONFIG_QSPI_BOOT)
413 #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
414 #define CONFIG_ENV_OFFSET               0x300000        /* 3MB */
415 #define CONFIG_ENV_SECT_SIZE            0x10000
416 #else
417 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x300000)
418 #define CONFIG_ENV_SECT_SIZE            0x20000
419 #define CONFIG_ENV_SIZE                 0x20000
420 #endif
421
422 #define CONFIG_CMDLINE_TAG
423
424 #undef CONFIG_BOOTCOMMAND
425 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
426 #define CONFIG_BOOTCOMMAND              "sf probe && sf read $kernel_load "    \
427                                         "e0000 f00000 && bootm $kernel_load"
428 #else
429 #define CONFIG_BOOTCOMMAND              "cp.b $kernel_start $kernel_load "     \
430                                         "$kernel_size && bootm $kernel_load"
431 #endif
432
433 #include <asm/fsl_secure_boot.h>
434
435 #endif /* __LS1046AQDS_H__ */