1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright (C) 2015 Freescale Semiconductor
6 #ifndef __LS1043A_COMMON_H
7 #define __LS1043A_COMMON_H
10 #ifdef CONFIG_SPL_BUILD
21 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
24 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT_QSPI))
28 #define CONFIG_REMAKE_ELF
31 #include <asm/arch/stream_id_lsch2.h>
32 #include <asm/arch/config.h>
34 /* Link Definitions */
36 #define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
38 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
41 #define CONFIG_SKIP_LOWLEVEL_INIT
43 #define CONFIG_VERY_BIG_RAM
44 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
45 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
46 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
47 #define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL
49 #define CPU_RELEASE_ADDR secondary_boot_func
51 /* Generic Timer Definitions */
52 #define COUNTER_FREQUENCY 25000000 /* 25MHz */
54 /* Size of malloc() pool */
55 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)
58 #define CONFIG_SYS_NS16550_SERIAL
59 #define CONFIG_SYS_NS16550_REG_SIZE 1
60 #define CONFIG_SYS_NS16550_CLK (get_serial_clock())
62 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
67 #define CONFIG_SPL_TEXT_BASE 0x10000000
68 #define CONFIG_SPL_MAX_SIZE 0x17000
69 #define CONFIG_SPL_STACK 0x1001e000
70 #define CONFIG_SPL_PAD_TO 0x1d000
72 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
73 CONFIG_SPL_BSS_MAX_SIZE)
74 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
75 #define CONFIG_SPL_BSS_START_ADDR 0x8f000000
76 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000
78 #ifdef CONFIG_SECURE_BOOT
79 #define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
81 * HDR would be appended at end of image and copied to DDR along
82 * with U-Boot image. Here u-boot max. size is 512K. So if binary
83 * size increases then increase this size in case of secure boot as
84 * it uses raw u-boot image instead of fit image.
86 #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
88 #define CONFIG_SYS_MONITOR_LEN 0x100000
89 #endif /* ifdef CONFIG_SECURE_BOOT */
93 #ifdef CONFIG_NAND_BOOT
94 #define CONFIG_SPL_PBL_PAD
95 #define CONFIG_SPL_TEXT_BASE 0x10000000
96 #define CONFIG_SPL_MAX_SIZE 0x1a000
97 #define CONFIG_SPL_STACK 0x1001d000
98 #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
99 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
100 #define CONFIG_SYS_SPL_MALLOC_START 0x80200000
101 #define CONFIG_SPL_BSS_START_ADDR 0x80100000
102 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
103 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000
105 #ifdef CONFIG_SECURE_BOOT
106 #define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
107 #endif /* ifdef CONFIG_SECURE_BOOT */
109 #ifdef CONFIG_U_BOOT_HDR_SIZE
111 * HDR would be appended at end of image and copied to DDR along
112 * with U-Boot image. Here u-boot max. size is 512K. So if binary
113 * size increases then increase this size in case of secure boot as
114 * it uses raw u-boot image instead of fit image.
116 #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
118 #define CONFIG_SYS_MONITOR_LEN 0x100000
119 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
125 #if defined(CONFIG_TFABOOT) || \
126 (!defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI))
127 #define CONFIG_FSL_IFC
129 * CONFIG_SYS_FLASH_BASE has the final address (core view)
130 * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
131 * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
132 * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
134 #define CONFIG_SYS_FLASH_BASE 0x60000000
135 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
136 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
138 #ifdef CONFIG_MTD_NOR_FLASH
139 #define CONFIG_SYS_FLASH_QUIET_TEST
140 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
146 #define CONFIG_SYS_I2C
150 #define CONFIG_PCIE1 /* PCIE controller 1 */
151 #define CONFIG_PCIE2 /* PCIE controller 2 */
152 #define CONFIG_PCIE3 /* PCIE controller 3 */
155 #define CONFIG_PCI_SCAN_SHOW
159 /* Command line configuration */
164 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
170 #define CONFIG_FSL_DSPI
171 #ifdef CONFIG_FSL_DSPI
172 #define CONFIG_DM_SPI_FLASH
173 #define CONFIG_SPI_FLASH_STMICRO /* cs0 */
174 #define CONFIG_SPI_FLASH_SST /* cs1 */
175 #define CONFIG_SPI_FLASH_EON /* cs2 */
181 #define CONFIG_SYS_DPAA_FMAN
182 #ifdef CONFIG_SYS_DPAA_FMAN
183 #define CONFIG_SYS_FM_MURAM_SIZE 0x60000
185 #ifdef CONFIG_TFABOOT
186 #define CONFIG_SYS_FMAN_FW_ADDR 0x900000
187 #define CONFIG_SYS_QE_FW_ADDR 0x940000
189 #define CONFIG_ENV_SPI_BUS 0
190 #define CONFIG_ENV_SPI_CS 0
191 #define CONFIG_ENV_SPI_MAX_HZ 1000000
192 #define CONFIG_ENV_SPI_MODE 0x03
195 #ifdef CONFIG_NAND_BOOT
196 /* Store Fman ucode at offeset 0x900000(72 blocks). */
197 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
198 #define CONFIG_SYS_FMAN_FW_ADDR (72 * CONFIG_SYS_NAND_BLOCK_SIZE)
199 #elif defined(CONFIG_SD_BOOT)
201 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
202 * about 1MB (2040 blocks), Env is stored after the image, and the env size is
203 * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800).
205 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
206 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800)
207 #define CONFIG_SYS_QE_FW_ADDR (512 * 0x4A00)
208 #elif defined(CONFIG_QSPI_BOOT)
209 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
210 #define CONFIG_SYS_FMAN_FW_ADDR 0x40900000
211 #define CONFIG_ENV_SPI_BUS 0
212 #define CONFIG_ENV_SPI_CS 0
213 #define CONFIG_ENV_SPI_MAX_HZ 1000000
214 #define CONFIG_ENV_SPI_MODE 0x03
216 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
217 /* FMan fireware Pre-load address */
218 #define CONFIG_SYS_FMAN_FW_ADDR 0x60900000
219 #define CONFIG_SYS_QE_FW_ADDR 0x60940000
222 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
223 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
227 /* Miscellaneous configurable options */
228 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
230 #define CONFIG_HWCONFIG
231 #define HWCONFIG_BUFFER_SIZE 128
234 #ifndef CONFIG_SPL_BUILD
235 #define BOOT_TARGET_DEVICES(func) \
239 #include <config_distro_bootcmd.h>
242 /* Initial environment variables */
243 #define CONFIG_EXTRA_ENV_SETTINGS \
244 "hwconfig=fsl_ddr:bank_intlv=auto\0" \
245 "fdt_high=0xffffffffffffffff\0" \
246 "initrd_high=0xffffffffffffffff\0" \
247 "fdt_addr=0x64f00000\0" \
248 "kernel_addr=0x61000000\0" \
249 "scriptaddr=0x80000000\0" \
250 "scripthdraddr=0x80080000\0" \
251 "fdtheader_addr_r=0x80100000\0" \
252 "kernelheader_addr_r=0x80200000\0" \
253 "kernel_addr_r=0x81000000\0" \
254 "kernel_start=0x1000000\0" \
255 "kernelheader_start=0x800000\0" \
256 "fdt_addr_r=0x90000000\0" \
257 "load_addr=0xa0000000\0" \
258 "kernelheader_addr=0x60800000\0" \
259 "kernel_size=0x2800000\0" \
260 "kernelheader_size=0x40000\0" \
261 "kernel_addr_sd=0x8000\0" \
262 "kernel_size_sd=0x14000\0" \
263 "kernelhdr_addr_sd=0x4000\0" \
264 "kernelhdr_size_sd=0x10\0" \
265 "console=ttyS0,115200\0" \
267 "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
269 "boot_scripts=ls1043ardb_boot.scr\0" \
270 "boot_script_hdr=hdr_ls1043ardb_bs.out\0" \
271 "scan_dev_for_boot_part=" \
272 "part list ${devtype} ${devnum} devplist; " \
273 "env exists devplist || setenv devplist 1; " \
274 "for distro_bootpart in ${devplist}; do " \
275 "if fstype ${devtype} " \
276 "${devnum}:${distro_bootpart} " \
277 "bootfstype; then " \
278 "run scan_dev_for_boot; " \
282 "load ${devtype} ${devnum}:${distro_bootpart} " \
283 "${scriptaddr} ${prefix}${script}; " \
284 "env exists secureboot && load ${devtype} " \
285 "${devnum}:${distro_bootpart} " \
286 "${scripthdraddr} ${prefix}${boot_script_hdr} " \
287 "&& esbc_validate ${scripthdraddr};" \
288 "source ${scriptaddr}\0" \
289 "qspi_bootcmd=echo Trying load from qspi..;" \
290 "sf probe && sf read $load_addr " \
291 "$kernel_addr $kernel_size; env exists secureboot " \
292 "&& sf read $kernelheader_addr_r $kernelheader_addr " \
293 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
294 "bootm $load_addr#$board\0" \
295 "nor_bootcmd=echo Trying load from nor..;" \
296 "cp.b $kernel_addr $load_addr " \
297 "$kernel_size; env exists secureboot " \
298 "&& cp.b $kernelheader_addr $kernelheader_addr_r " \
299 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
300 "bootm $load_addr#$board\0" \
301 "nand_bootcmd=echo Trying load from NAND..;" \
302 "nand info; nand read $load_addr " \
303 "$kernel_start $kernel_size; env exists secureboot " \
304 "&& nand read $kernelheader_addr_r $kernelheader_start " \
305 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
306 "bootm $load_addr#$board\0" \
307 "sd_bootcmd=echo Trying load from SD ..;" \
308 "mmcinfo; mmc read $load_addr " \
309 "$kernel_addr_sd $kernel_size_sd && " \
310 "env exists secureboot && mmc read $kernelheader_addr_r " \
311 "$kernelhdr_addr_sd $kernelhdr_size_sd " \
312 " && esbc_validate ${kernelheader_addr_r};" \
313 "bootm $load_addr#$board\0"
316 #undef CONFIG_BOOTCOMMAND
317 #ifdef CONFIG_TFABOOT
318 #define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
319 "env exists secureboot && esbc_halt;"
320 #define SD_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; " \
321 "env exists secureboot && esbc_halt;"
322 #define IFC_NOR_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd; " \
323 "env exists secureboot && esbc_halt;"
324 #define IFC_NAND_BOOTCOMMAND "run distro_bootcmd; run nand_bootcmd; " \
325 "env exists secureboot && esbc_halt;"
327 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
328 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
329 "env exists secureboot && esbc_halt;"
330 #elif defined(CONFIG_SD_BOOT)
331 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; " \
332 "env exists secureboot && esbc_halt;"
334 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd; " \
335 "env exists secureboot && esbc_halt;"
340 /* Monitor Command Prompt */
341 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
343 #define CONFIG_SYS_MAXARGS 64 /* max command args */
345 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
347 #include <asm/arch/soc.h>
349 #endif /* __LS1043A_COMMON_H */